Training and optimization of an artificial neural network controlling a hybrid power filter

A hybrid power compensator (HPC) consisting of a static VAr compensator and a dynamic compensator needs to be optimally controlled during the compensation of nonlinear loads. The HPC must be controlled to meet minimum requirements in terms of power factor and harmonic distortion, while at the same time minimizing its total cost. An artificial neural network (ANN) is used to control the HPC amidst a very dynamic power system environment. The performance of a reference ANN is evaluated while controlling an HPC connected to a typical nonlinear industrial load. The training and performance of the ANN is then optimized in terms of training set size, training set packing and ANN topology and the performance compared to the reference ANN. This paper highlights the importance of optimising the mentioned ANN parameters to achieve optimum ANN training and modeling accuracy. The results obtained reveals that the application of an ANN in controlling an HPC is feasible given that the ANN parameters are chosen appropriately.     

A VQ-based blind image restoration algorithm

Learning-based algorithms for image restoration and blind image restoration are proposed. Such algorithms deviate from the traditional approaches in this area, by utilizing priors that are learned from similar images. Original images and their degraded versions by the known degradation operator (restoration problem) are utilized for designing the VQ codebooks. The codevectors are designed using the blurred images. For each such vector, the high frequency information obtained from the original images is also available. During restoration, the high frequency information of a given degraded image is estimated from its low frequency information based on the codebooks. For the blind restoration problem, a number of codebooks are designed corresponding to various versions of the blurring function. Given a noisy and blurred image, one of the codebooks is chosen based on a similarity measure, therefore providing the identification of the blur. To make the restoration process computationally efficient, the principal component analysis (PCA) and VQ-nearest neighbor approaches are utilized. Simulation results are presented to demonstrate the effectiveness of the proposed algorithms.     

High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

Start-up and steady-state results of a full-scale UASB reactor treating malting wastewater.

An Imhoff tank was reconstructed into a 250 m3 UASB reactor in order to treat a malting plant wastewater. The UASB was inoculated with sludge from an anaerobic lagoon used for slaughterhouse wastewater treatment. After two months of operation the reactor achieved full load with an HRT of 17 h, a COD removal higher than 80% and a biogas production of 300 m3/day (77% average methane content), with an organic loading rate of 3.6 kgCOD/m3.d (0.24 kgCOD/kgVSS.d). A yield coefficient of 0.09 gVSS/gCODrem was found from a mass balance. The fat present in the inoculated sludge (48 mg/gSSV) did not affect the start up performance. Sludge from the inoculum with high content of fat (270 mg/gSSV), was separated by flotation in the first week of operation. The COD removal efficiency was scarcely influenced by the reactor operation temperature (17-25 degrees C).     

Bio-layer management in anaerobic membrane bioreactors for wastewater treatment.

Membrane separation technology represents an alternative way to achieve biomass retention in anaerobic bioreactors for wastewater treatment. Due to high biomass concentrations of anaerobic reactors, cake formation is likely to represent a major cause of flux decline. In the presented research, experiments are performed on the effect of biomass concentration and level of gas sparging on the hydraulic capacity of a submerged anaerobic membrane bioreactor. Both parameters significantly affected the hydraulic capacity, with biomass exerting the most pronounced effect. After 50 days of continuous operation the critical flux remained virtually unchanged, despite an increase in membrane resistance, suggesting that biomass characteristics and hydraulic conditions determine the bio-layer formation rather than the membrane's fouling level. The concept of bio-layer management is introduced to describe the programmed combination of actions performed in order to control the formation of biomass layer over membranes.     

Segmented polymer networks containing amino‐dendrimers

Polymer networks in which poly(propylene imine) dendrimers (Astramol?) are connected to each other by linear polytetrahydrofuran (polyTHF) segments, were prepared by two methods. The first method was a one‐step procedure in which bifunctionally living polyTHF, obtained by initiation of the THF polymerization with trifluoromethane sulfonic anhydride (triflic anhydride), was reacted with an amino‐dendrimer. This reaction was very fast but did not allow formation of the end products. The second method was a two‐step procedure. In a first step, living polyTHF, prepared with acryloyloxybutyl triflate as initiator, was grafted on an amino‐dendrimer, to form a star‐like, acrylate‐terminated polyTHF multi‐macromonomer with the dendrimer as core. In a second step, networks were obtained by Michael addition between the acrylate end‐groups and unreacted amino‐groups of the dendrimer. This cross‐linking reaction occurred spontaneously upon heating of the solution of the multi‐macromonomer with gelation times varying from a few minutes to a few hours, depending on the temperature and the composition of the prepolymers. With this method it was possible to prepare networks in the form of coatings or films. © 2003 Society of Chemical Industry     

Wavelength-tunable 40-GHz picosecond harmonically mode-locked fiber laser source

We demonstrate a novel 40-GHz mode-locked fiber laser that utilizes a single active device to provide both gain and mode-locking. The laser produces pulses as short as 2.2 ps, is tunable over a 27-nm band centered at 1553 nm, and exhibits long-term stability without cavity-length feedback control. The pulse train at 1556 nm was used in a 40-Gb/s transmission experiment over 45 km with a low 0.4-dB power penalty.