The effect of plastic deformation on Al2CuLi (T 1) precipitation

The enhancement ofT ₁ precipitation in Al-Li-Cu alloys by plastic deformation prior to aging (that is, cold work) and the subsequent increase in alloy strength is investigated. The increased understanding of the role of matrix dislocations in the nucleation and growth ofT ₁ plates, discussed in the previous paper,^[1] permits a detailed study of the phenomenon. In this paper, the effect of different levels of plastic strain on theT ₁ particle distributions as a function of aging time at 190 °C is quantified, and the subsequent influence on tensile properties is thereby described. The effect of plastic deformation is shown to decrease theT ₁ plate length and thickness, increase the number density by almost two orders of magnitude, increase the yield strength by 100 MPa, while simultaneously reaching peak strength in 20 pct of the time required without plastic deformation. Formerly Graduate Student, Department of Materials Science, University of Virginia,     

Sensory analysis of polystyrene packaging material taint in cocoa powder for drinks and chocolate flakes

Polystyrene packaging material taint was sensorily evaluated in cocoa powder for drinks and chocolate flakes using short-cut signal detection measures on differences between control and test samples and on recognition of styrene. No differences were observed in cocoa powder for drinks and plain chocolate flakes treated with 0.5 dm2 polystyrene of 1 mm thickness. However, differences were detected in milk chocolate flakes and plain chocolate flakes, which were in contact with a larger area or thicker polystyrene packaging material. The latter results were confirmed by the styrene recognition test, so polystyrene is a potential source of off-flavour for chocolate products. The amount of residual styrene in the polystyrene used was about 320 ppm, while the amounts of styrene ranged from 7 to 132 ppb in cocoa drinks and from 414 to 1447 ppb in chocolate flakes.     

Electrochemical Faceting of polycrystalline platinum in HF solutions

The electrochemical faceting of polycrystalline (pc) platinum yielding a (100)-preferred oriented electrode surface was accomplished in HF solutions by applying to the pc platinum electrode a square wave potential perturbation at 1 kHz in the 0.2 to 1.3 V range (vs rhe). SEM patterns of the resulting surfaces were also obtained. For HF concentrations up to 2 M no appreciable influence of the electrolyte concentration on the electrochemical faceting was noticed. Otherwise, the voltammetric response of the (100)-type preferred oriented platinum surface in the H-adatom potential range when compared to previously reported data resulted remarkably sensitive to the electrolyte composition. The discussion of results was based on the non-equilibrium adsorption conditions for anions under the periodic perturbation.     

Current and future water issues in the Oldman River Basin of Alberta, Canada.

Long-term trends in alpine and prairie snow pack accumulation and melt are affecting streamflow within the Oldman River Basin in southern Alberta, Canada. Unchecked rural and urban development also has contributed to changes in water quality, including enhanced microbial populations and increased waterborne pathogen occurrence. In this study we look at changing environment within the Oldman River Basin and its impact on water quality and quantity. The cumulative effects include a decline in net water supplies, and declining quality resulting in increased risk of disease. Our data indicates that decreases in the rate of flow of water can result in sedimentation of bacterial contaminants within the water column. Water for ecosystems, urban consumption, recreation and distribution through irrigation is often drawn from waterholding facilities such as dams and weirs, and concern must be expressed over the potential for contaminate build-up and disproportionate potential of these structures to pose a risk to human and animal health. With disruption of natural flow rates for water resulting from environmental change such as global warming and/or human intervention, increased attention needs to be paid to use of best management practices to protect source water supplies.     

Effects of compressive and tensile stress on the growth mode of epitaxial oxide films

Oxide films were deposited on different substrates by laser molecular beam epitaxy. Reflection high-energy electron diffraction was performed to in situ investigate the change of growth mode and the lattice relaxation during the growth. An asymmetrical phenomenon was found in the two kinds of strain states, compressive stress and tensile stress of heterostructures with different lattice mismatch. In the case of BaTiO₃/SrTiO₃ (2.2%), 2D layer-by-layer growth mode without lattice relaxation can be maintained for a longer period for BTO films on STO with compressive stress, comparing to STO films on BTO with tensile stress. When MgO films were deposited on SrTiO₃ with a large mismatch of 7.8%, compressive stress leads to rapid lattice relaxation with a very thin wet layer, and 3D strained island were observed. As a comparison, SrTiO₃ films on MgO with tensile stress were configured. No RHEED patterns can be observed duo to a large tensile stress.     

Integration of prior knowledge of measurement noise in kernel density classification

Samples can be measured with different precisions and reliabilities in different experiments, or even within the same experiment. These varying levels of measurement noise may deteriorate the performance of a pattern recognition system, if not treated with care. Here we seek to investigate the benefit of incorporating prior knowledge about measurement noise into system construction. We propose a kernel density classifier which integrates such prior knowledge. Instead of using an identical kernel for each sample, we transform the prior knowledge into a distinct kernel for each sample. The integration procedure is straightforward and easy to interpret. In addition, we show how to estimate the diverse measurement noise levels in a real world dataset. Compared to the basic methods, the new kernel density classifier can give a significantly better classification performance. As expected, this improvement is more obvious for small sample size datasets and large number of features.     

Predeployed secure key distribution mechanisms in sensor networks: current state-of-the-art and a new approach using time information

In this article we survey a number of predeployed secure key distribution (PSKD) schemes proposed in the technical literature. We also propose a new time-based PSKD (TPSKD), which operates under the assumption of loose time synchronization, and discuss the performance of the scheme. Since the TPSKD scheme uses time information, which would typically already be available in sensor nodes, the cost of the scheme?s implementation is low.     

Noise–Power Optimization of Incremental Data Converters

Incremental data converters (IDCs) are useful in instrumentation and measurement applications, where low-frequency analog signals need to be converted into digital form with high accuracy and low power dissipation. They are particularly well suited for applications where a single analog-digital converter is multiplexed between many channels. This paper proposes an exact design methodology for IDCs, which optimizes the signal-to-noise ratio of the converter under practical design constraints. The process also allows the designer to apportion the noise budget in an arbitrary manner between thermal and quantization noise. The design process is illustrated by an example which describes the optimization of a third-order multiplexed IDC.     

A Novel Ordered Nanopore Array Diode Laser

In this work, we have created a new type of structure, the nanopore active layer, for achieving quantization of carrier states in a semiconductor. The nanopore structure consists of a periodic two-dimensional array of localized energy barriers perturbing an otherwise conventional quantum well. This perturbation leads to the formation of intraband forbidden energy gaps which are observed experimentally.     

Photo-Fenton removal of water-soluble polymers

This paper presents the results of experiments carried out in a laboratory-scale photochemical reactor on the photodegradation of different polymers in aqueous solutions by the photo-Fenton process. Solutions of three polymers, polyethyleneglicol (PEG), polyacrylamide (PAM), and polyvinylpyrrolidone (PVP), were tested under different conditions. The reaction progress was evaluated by sampling and analyzing the total organic carbon concentration in solution (TOC) along the reaction time. The behavior of the different polymers is discussed, based on the evolution of the TOC–time curves. Under specific reaction conditions, the formation and coalescence of solid particles was visually observed. Solids formation occurred simultaneously to a sharp decrease in the TOC of the liquid phase. This may be favorable for the treatment of industrial wastewater containing polymers, since the photodegradation process can be coupled with solid separation systems, which may reduce the treatment cost.