Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

1H T2‐NMR monitoring of crosslinked polyolefin aging

This work examines the correlation between the ¹H‐NMR T₂ relaxation constant and the mechanical properties of aged crosslinked polyolefin cable insulation. T₂ experiments on unswollen samples could not differentiate between unaged and highly aged materials; all exhibited ¹H T₂ constants of approximately 0.5 ms. To accentuate the effects of aging, samples were swollen in various solvents. Unaged samples had T₂ values of approximately 15 ms in good solvents. With thermal aging, T₂ values decreased as the ultimate tensile elongation decreased. However, the correlation between T₂ and elongation differed for samples irradiated with high‐energy radiation and for materials aged above versus below the crystalline melting temperature. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2578–2582, 2003     

Effect of anisotropy of tin on thermomechanical behavior of solder joints

Properties of body centered tetragonal tin are highly anisotropic. As a consequence large stresses can develop at the tin grain boundaries due to coefficient of thermal expansion mismatch during temperature excursions. A modeling approach to evaluate the 3D stress states that develop at grain boundaries during thermomechanical fatigue in tin-based solder is presented. Development of significant amounts of stresses in the plane of the grain boundary can cause grain-boundary sliding and surface-relief effects, while those normal to the grain boundary can cause grain-boundary decohesion and cracking.     

The effects of nonlocal impact ionization on the speed of avalanche photodiodes

The nonlocal enhancement in the velocities of charge carriers to ionization is shown to outweigh the opposing effects of dead space, increasing the avalanche speed of short avalanche photodiodes (APDs) over the predictions of a conventional local model which ignores both of these effects. The trends in the measured gain-bandwidth product of two short InAlAs APDs reported in the literature support this result. Relatively large speed benefits are predicted to result from further small reductions in the lengths of short multiplication regions.     

Inside Front Cover: The Elastic Properties and Plastic Behavior of Two‐Dimensional Polymer Structures Fabricated by Laser Interference Lithography (Adv. Funct. Mater. 10/2006)

The probing of the micromechanical properties within a two‐dimensional polymer structure with sixfold symmetry fabricated via interference lithography reveals a nonuniform spatial distribution in the elastic modulus “imprinted” with an interference pattern in work reported by Tsukruk, Thomas, and co‐workers on p. 1324. The image prepared by M. Lemieux and T. Gorishnyy shows how the interference pattern is formed by three laser beams and is transferred to the solid polymer structure. The elastic and plastic properties within a two‐dimensional polymer (SU8) structure with sixfold symmetry fabricated via interference lithography are presented. There is a nonuniform spatial distribution in the elastic modulus, with a higher elastic modulus obtained for nodes (brightest regions in the laser interference pattern) and a lower elastic modulus for beams (darkest regions in the laser interference pattern) of the photopatterned films. We suggest that such a nonuniformity and unusual plastic behavior are related to the variable material properties “imprinted” by the interference pattern.     

The influence of oxygen partial pressure on growth of the (Hg,Re)-1223 intergrain junction

Hg/sub 0.82/Re/sub 0.18/Ba/sub 2/Ca/sub 2/Cu/sub 3/O/sub 8+/spl delta// polycrystalline samples were successfully obtained by using different oxygen partial pressure in the annealing treatment of the precursor ceramic. The doping state was confirmed by X-ray powder diffraction pattern analysis and by observing distinct thermopower values at room temperature. Also, the intergrain regions have shown an improvement in the critical current density when using the precursor preparation with 10% O/sub 2/ and 90% Ar (optimal doped). The optimal doped sample has presented the highest /spl alpha/ exponent of the J/sub c//spl prop/[1-(T/T/sub c/)/sup 2/]/sup /spl alpha// dependence. For the case of (Hg,Re)-1223 polycrystalline superconductor applications, the /spl alpha/ exponent can be used as a junction quality parameter.     

Evaluation of Atmospheric and Vacuum Residues Using Molecular Distillation and Optimization

The term atmospheric residue describes the material at the bottom of the atmospheric distillation tower having a lower boiling point limit of about 340°C; the term vacuum residue (heavy petroleum fractions) refers to the bottom of the vacuum distillation, which has an atmospheric equivalent boiling point (AEBP) above 540°C. In this work, the objective is to evaluate the behavior of different kinds of Brazilian atmospheric and vacuum residues using molecular distillation. The Falling Film Molecular Distillator was used. For the results obtained through this process, a significant range of temperature can be explored avoiding the thermal decomposition of the material. So these results are very important to the refinery decisions and improvements. The Experimental Factorial Design results showed that the temperature has more influence on the process than the feed flow rate, when a higher percentage of distillate is required.     

Mobile Device Security Using Transient Authentication

Mobile devices are vulnerable to theft and loss due to their small size and the characteristics of their common usage environment. Since they allow users to work while away from their desk, they are most useful in public locations and while traveling. Unfortunately, this is also where they are most at risk. Existing schemes for securing data either do not protect the device after it is stolen or require bothersome reauthentication. Transient Authentication lifts the burden of authentication from the user by use of a wearable token that constantly attests to the user's presence. When the user departs, the token and device lose contact and the device secures itself. We show how to leverage this authentication framework to secure all the memory and storage locations on a device into which secrets may creep. Our evaluation shows this is done without inconveniencing the user, while imposing a minimal performance overhead     

A closed loop exponential feeding law: Invariance and global stability analysis

This article addresses the computation of invariant control laws [A. Fradkov, I. Miroshnik, V. Nikiforov, Nonlinear and Adaptive Control of Complex Systems, Kluwer, 1999] for fed-batch fermenters represented by two standard models. It will be shown how to derive partial state feedbacks that, assuming ideal conditions and perfect model, keep the specific growth rate μ constant provided the initial conditions are adequate. The invariant control law is the closed loop version of the exponential feeding already suggested in several references as shown later. The paper presents an analysis of invariance and a study of global stability within the framework of partial stability. That is, stability with respect to some of the state variables. This enables us to treat the case with Haldane-like or non-monotonous kinetics.