Interval based MINLP superstructure synthesis of mass exchange networks

A new simultaneous synthesis approach for mass exchange networks (MENs) is presented. The technique is adapted from the interval based mixed integer non-linear program (MINLP) superstructure (IBMS) synthesis of heat exchanger networks (HENs). The superstructure interval boundary compositions are defined by the supply and target compositions of either the rich or lean set of streams. Each rich and lean stream in the superstructure has the potential of exchanging mass with streams of opposite kind in each interval based on mass transfer feasibility. The model harnesses the strengths of the stagewise superstructure and the pinch technology methods for mass exchange network synthesis (MENS). The IBMS approach simultaneously trades-off the capital and operating costs for MENs. The superstructure composition interval defining approach introduced in this paper enforces the mixing of split streams at equal compositions, hence there is no need to include mixing equations in the model. Fixing the interval boundaries helps to eliminate the complexities involved in initialisations, thus the region of search for the optimum solution is reduced. The IBMS model is applied to MENS problems involving continuous contact and staged columns. It is also extended to problems involving multiple mass separating agents (MSAs) and regeneration. The results obtained compare well with those in the literature.     

Determining Frequency and Impulse Response Using Asymmetrical Pulses

A method is presented and analyzed for determining the impulse response and frequency response of a system using an asymmetrical stimulus signal. The considered signal is a pulse with a rapid first transition, followed by a nearly constant region, and then followed by a second transition that is much slower than the first. The advantage of such a signal is that unlike a symmetric pulse, its Fourier transform has no zeros. This allows one to divide by the Fourier transform in the data analysis. It is shown that such a pulse retains the advantages of using an impulse or steplike stimulus. Error estimates similar to those previously published for impulse and steplike stimuli are given for the asymmetric stimulus     

Eigenspannungen als Messgröße zur Qualitätssicherung

Residual stress as measured quantity in quality assurance The x‐ray method is used in the Volkswagen Automotive Group at different world‐wide locations as a standard procedure to determine residual stress. As an important measured quantity in the quality assurance residual stresses are specified in drawings of different components (e.g. gears, coil springs). Measurements are carried out during quality assurance, production, damage analyse, technical development department and design control of components from suppliers. An optimum efficiency can be achieved, if it exists a unique correlation between residual stress values and loading capacity of components, and if the processes to introduce residual stress can be optimized using residual stress measurements during the production.     

Conditionals and conditional probability.

The authors report 3 experiments in which participants were invited to judge the probability of statements of the form if p then q given frequency information about the cases pq, p?q, ?pq, and ?p?q (where ? = not). Three hypotheses were compared: (a) that people equate the probability with that of the material conditional, 1 - P(p?q); (b) that people assign the conditional probability, P(q/p); and (c) that people assign the conjunctive probability P(pq). The experimental evidence allowed rejection of the 1st hypothesis but provided some support for the 2nd and 3rd hypotheses. Individual difference analyses showed that half of the participants used conditional probability and that most of the remaining participants used conjunctive probability as the basis of their judgments. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Iron–cobalt catalysts synthesized by a reverse micelle impregnation method for controlled growth of carbon nanotubes

Fe–Co bimetallic metals supported on CaCO₃ support have been prepared using three different methods for the preparation of the catalysts; wet impregnation (IMP), deposition–precipitation (DP) and reverse micelle impregnation (RM). By careful choice and optimization of CVD reaction conditions and catalyst preparation procedures, we have tailored the nanofabrication of CNTs using 5 wt.% Fe–Co/CaCO₃. High yields of ‘clean’ MWNTs with near 100% selectivity and excellent reproducibility were obtained (1215% and 835% yields for the IMP and DP methods respectively). The RM technique enabled more precise control over the size of the CNTs and a narrower diameter distribution (3–5 nm i.d. and 10–15 nm o.d.) was obtained.     

Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

Techno-economic study of different alternatives for biodiesel production

Biodiesel has become an attractive diesel fuel substitute due to its environmental benefits since it can be made from renewable resource. However, the high costs surrounding biodiesel production remains the main problem in making it competitive in the fuel market either as a blend or as a neat fuel. More than 80% of the production cost is associated with the feedstock itself and consequently, efforts are focused on developing technologies capable of using lower-cost feedstocks, such as recycled cooking oils and wastes from animal or vegetable oil processing operations.     

High yield formation of carbon nanotubes using a rotating cathode in open air

Carbon nanotubes (CNTs) have been synthesized using the arc discharge method with a rotating graphite disc as the cathode. Arcing was carried out in open air and without the use of catalysts. The current density was maintained constant through out the experiment, while, the rate of rotation of the cathode and atmosphere under which arcing was carried out were changed during experimentation. Characterization of the samples produced indicates that rotation of the cathode has a significant impact on the quality and yield of the process. It is proposed that rotation of the cathode drags plasma formed between two electrodes away from high temperature region. This results in a sudden quenching of the reactive plasma. The time available for nucleation and growth phenomena is significantly reduced and thus leads to the formation of highly graphitic multi walled CNTs (yield 60%) and traces of double walled CNTs.     

A rubber-modified thermoplastic where the morphology produced by phase-separation induced by polymerization disappears at high conversions

An unexpected experimental finding is reported where the primary morphology developed during polymerization-induced phase separation in a rubber-modified thermoplastic practically disappears at high conversions. This process was evidenced by light scattering (LS) and scanning electron microscopy (SEM) for a particular composition of solutions of polyisobutylene oligomers (PIB) in isobornylmethacrylate (IBoMA), during the free-radical polymerization of the monomer. The primary phase separation produced a dispersion of domains rich in PIB containing significant amounts of the monomer (IBoMA). Polymerization of the monomer in these domains occurred at high overall conversions producing the filling of dispersed domains with a PIBoMA-PIB blend that could not be distinguished from the matrix. Under these conditions the final material had the appearance of a homogeneous blend.     

Exit effect on hydrodynamics of the internal circulating fluidized bed riser

This is the first time an extensive investigation has been carried out regarding the effects of riser exit geometry on pressure drop and solid behaviour inside the Internal Circulating Fluidized Bed (ICFB) riser, using different riser exit geometries at several operating conditions.The Radioactive Particle-Tracking (RPT) technique was used for solid concentration measurements and solid residence time distribution at the exit zone. Experiments were conducted using Geldart B particles, in the gas superficial velocity range of 4 to 10 m/s. Axial solid hold-up, solid residence time distribution in the exit zone, and the reflux ratio factor k_m, (defined earlier by [E.H. Van der Meer, R.B. Thorpe, J.F. Davidson, Flow patterns in the square cross-section riser of a circulating fluidized bed and the effect of riser exit design, Chem. Eng. Sc. 55 (19) (2000) 4079-4099]), were the main criteria used to investigate the impact of gas-solid separator devices implemented at the ICFB riser exit.Solid residence time distribution results and axial solid hold-up profiles provided clear evidence that the separator device at the riser exit strongly influences the hydrodynamic structure of the ICFB riser. The V-shaped riser exit geometry was found to be the optimum of all the configurations studied.