Stoichiometric dye-binding procedure for the determination of the reactive lysine content of soya bean protein

A new analytical method has been developed for the determination of the reactive lysine content of soya bean protein. The method is based on the reaction of the free basic groups of the protein with 1-phenylazo-2 naphthol-6,8 disulphonic acid. With regard to the stoichiometry of the procedure, it has been proved, contrary to earlier reports, that the basic amino acids, histidine, arginine and lysine, each combine with one mole of the dye. After acylation with propionic anhydride lysine alone loses its dye reactivity. The usefulness of the proposed method has been demonstrated by the determination of the reactive lysine content of several untreated, heat-treated and acid-treated soya bean samples. The results show that heat damage of about 5% in reactive lysine content can be measured in 1·5 h with good reproducibility.     

Multitemporal passive microwave mapping in MACHYDRO'90

MACHYDR0'90 was an experiment conducted in Pennsylvania in 1990 to study the synergistic use of remote sensors in multitemporal hydrologic studies. As part of this mission the pushbroom microwave radiometer was flown and used to produce brightness temperature maps. Verification studies and vegetation algorithms for mixed land cover areas are described     

Survival of Yersinia enterocolitica and Escherichia coli in spring water

Survival of pure and mixed cultures of Yersinia enterocolitica and Escherichia coli in sterile spring water stored at 4 degrees C was evaluated. Y. enterocolitica increased two or three logs during the first 3 weeks of incubation, and at the end of 64 weeks viable cells in numbers corresponding to the initial inoculum level were still detectable. However, after 1 week of incubation, the number of E. coli in water started to decrease and in 13 weeks time no E. coli was detected. More rapid decrease of E. coli was observed in mixed cultures.     

Highly integrated direct conversion receiver for GSM/GPRS/EDGE with on-chip 84-dB dynamic range continuous-time /spl Sigma//spl Delta/ ADC

This paper describes a highly digitized direct conversion receiver of a single-chip quadruple-band RF transceiver that meets GSM/GPRS and EDGE requirements. The chip uses an advanced 0.25-/spl mu/m BiCMOS technology. The I and Q on-chip fifth-order single-bit continuous-time sigma-delta (/spl Sigma//spl Delta/) ADC has 84-dB dynamic range over a total bandwidth of /spl plusmn/135 kHz for an active area of 0.4 mm/sup 2/. Hence, most of the channel filtering is realized in a CMOS IC where digital processing is achieved at a lower cost. The systematic analysis of dc offset at each stage of the design enables to perform the dc offset cancellation loop in the digital domain as well. The receiver operates at 2.7 V with a current consumption of 75 mA. A first-order substrate coupling analysis enables to optimize the floor plan strategy. As a result, the receiver has an area of 1.8 mm/sup 2/.     

Application of Romero García method to the degradation process of DGEBA/ETDA filled with ultra fine metallic copper

Summary The thermal properties of an epoxy resin (diglycidyl ether Bisphenol A, DGEBA) cured with a primary amine (ethylenediamine, ETDA) and filled with 10, 20 and 30 wt. % of ultra fine copper particles were analyzed. The thermal results were evaluated by means of the Romero-Garcia method, which allowed to obtain the resin degradation kinetic parameters, as well as the possible decomposition mechanism. From the obtained results is possible to infer that higger copper content strongly affects the degradation process of the epoxy resin, which causes a drop off on the composites thermal stability. This behavior could be attributed to water presence, being this effect less pronounced for the resin with 10 wt. % copper and unfilled resin. Regarding to decomposition mechanism, three way transport showed the best correlation for all samples.     

A new pneumatic bearing dynamometer for power input measurement in stirred tanks

A turntable dynamometer has been constructed for the accurate measurement of power input and mixing applications in bench stirred tank reactors. The main feature of this device is a pneumatic bearing with complementary conical parts. The conical pneumatic bearing permitted to apply eccentric loads without affecting its stability. The static friction torque in the pneumatic bearing was very small, 4 × 10^?4 Nm, and can be neglected in the experimental ranges of measured torques, i.e. from 5 × 10^?3 to 2.21 Nm. In accordance with the instrumentation used, the deviations obtained with the apparatus are less than 10% at low torque readings. At moderate torques, deviations lower than 1% are routinely obtained. Several power input measurements show that the obtained data scatter is lower than 2.5%. The power input response in the turbulent regime is in agreement with dimensional analysis: the power input depends on the cube of the impeller speed. In addition, data obtained with a turbine impeller under ungassed conditions agree with the predictions of a published correlation, which takes into account several geometrical parameters.     

A distributed approach for access and visibility task with a manikin and a robot in a virtual reality environment

This paper presents a new method, based on a multi-agent system and on a digital mock-up technology, to assess an efficient path planner for a manikin or a robot for an access and visibility task taking into account ergonomic constraints or joint and mechanical limits. In order to solve this problem, the human operator is integrated in the process optimization to contribute to a global perception of the environment. This operator cooperates, in real time, with several automatic local elementary agents. The result of this work validates solutions through the digital mock-up; it can be applied to simulate maintainability and mountability tasks.