Spin Dependent Hopping in Ti Doped La0.67 Ca0.33 MnO3

A systematic investigation of the magnetic and transport properties of Ti doped La0.67Ca0.33MnO3 was reported. The Ti substitution for Mn ions results in a reduction in ferromagnetism and conductivity. The metal-insulator transition temperature is close to Curie temperature which decreases from 274 to 82 K as x increases from 0 to 0.17. The most important effect of Ti doping is to introduce spin clusters in the samples due to the distortion of local lattice and the inhomogeneous magnetic structure induced primarily by the random distribution of Mn ions. A maximum magnetoresistance ratio as large as 90% in 1 T at 122 K was obtained for the sample with x =0. 055, which is four times larger than that obtained for LCMO sample at 272 K. There is a remarkable field-history dependent MR in the cooling process for the doped samples while such phenomenon disappears in the warming run. The resistivity follows well the variable range hopping behavior in paramagnetic state. Both the size effect and spin dependent hopping of carriers between the spin clusters should be considered in this system.     

Preirradiation grafting of acrylic and methacrylic acid onto polyethylene films: Preparation and properties

The method of preirradiation grafting of acrylic acid and methacrylic acid onto polyethylene films was studied. The trapped radicals and hydroperoxides or diperoxides appeared to be able to induce graft polymerization. Mohr's salt was added to depress homopolymerization. The influences of crystallinity, dosage, and storage period on the grafting behavior were investigated from the viewpoint of practical application. At elevated temperature, the degree of grafting increased rapidly with reaction time initially, and then leveled off to the value of final percent grafting. Dosage and storage periods had greater extent of influence on the final percent grafting of LDPE than on that of HDPE. Electrical properties, transport properties, and mechanical properties were measured to compare the differences between acrylic-acid-and methacrylic-acid-grafted copolymer films. It was found that the properties of methacrylic-acid-grafted copolymer film was superior to those of acrylic-acid-grafted copolymer film, especially in electrical conductivity. The KOH diffusion test confirmed that grafting occurred not only on the surface but also in the interior of the polymer matrix, and the grafting is believed to proceed from the surface to the interior of the matrix.     

Traveling-wave piezoelectric linear motor Part I: the stator design.

A new type of piezoelectric linear motor incorporating a traveling wave has been developed. The linear motor is comprised of a stator and a carriage. The stator design, which consists of a meander-line structure and gear teeth mounted on the meander-line structure, is the focus of this article. The meander-line structure is constructed with bimorph actuators arranged in a line. These actuators are driven by two phased sets of alternating current (ac) in order to generate a traveling wave. The traveling wave is transferred to the gear teeth, by which the carriage is driven. Modeling of the stator is derived by use of a strain energy method. The performance of various materials is evaluated by analytical and experimental methods. The analytical and the experimental results are quite approximate. Modal analysis is investigated using ANSYS. Appropriate modes associated with ultrasonic levels of resonant frequency are selected to obtain desired motion and to enhance the output performance. Surface speed for various applied input voltage are studied and indicate a nearly linear relationship. The stator in combination with the carriage makes up the linear motor.     

Optimum power-saving method for power MOSFET width of DC/DC converters

An optimum power metal-oxide-semiconductor field effect transistor (MOSFET) width technique is proposed for enhancing the efficiency characteristics of switching DC-DC converters. By implementing a one-cycle buck DC-DC converter, it is demonstrated that the dynamic power MOSFET width controlling technique has a much improved power reduction whether the load current is light or heavy. The maximum efficiency of the buck converter is ~92% with a 3% efficiency improvement for the heavy load condition. The efficiency is further improved by ~16% for the light load condition as a result of the power reduction from the large power MOSFET transistors. Also proposed is a new error-correction loop circuit to enable a better load regulation than that of previous designs. Compared with the adaptive gate driver voltage technique, the optimum power MOSFET width can achieve a significant improvement in power saving. It is also superior to the low-voltage-swing MOSFET gate drive technique for switching DC-DC converters     

Enhancement of islanding-detection of distributed generation systems via wavelet transform-based approaches

In this paper, a wavelet transform-based approach is proposed to detect the occurrence of islanding events in distributed generation systems. Thanks to time–frequency localization capabilities exhibited by wavelet transform, the approach embedded with this transform technique has grasped the appearance of the islanding event in a highly effective manner. Moreover, for those regions which are in need of a better visualization, the proposed approach would serve as an efficient aid such that the mains power disconnection can be better distinguished. To validate the feasibility of this approach, the method has been validated through several scenarios. Test results supported the effectiveness of the method for the application considered.     

Plastic deformation and fracture of binary TiAl-base alloys

The mechanical behavior of binary TiAl alloys containing 46 to 60 at. pct Al has been studied in bulk materials preparedvia rapid solidification processing. Bending and tensile tests were carried out at room temperature as a function of Al concentration. A few alloys were also tested from liquid nitrogen temperature to ∼ 1000°C. Deformation substructures were studied by analytical transmission electron microscopy and fracture modes by scanning electron microscopy (SEM). It was found that both microstructure and composition strongly affect the mechanical behavior of TiAl-base alloys. A duplex structure, which contains both primary y grains and transformedγ/α ₂ lamellar grains, is more deformable than a single-phase or a fully transformed structure. The highest plasticities are observed in duplex alloys containing 48–50 at. pct Al after heat treatment in the center of theγ + α phase field. The deformation of these duplex alloys is facilitated by 1/2[110] slip and {111} twinning, but very limited superdislocation slip occurs. The twin deformation is suggested to result from a lowered stacking fault energy due to oxygen depletion or an intrinsic change in chemical bonding. Other factors, such as grain size and grain boundary chemistry and structure, are important from a fracture point of view. The results on the deformation and fracture modes as a function of test temperature are also discussed.     

Peripheral nerve injury as a complication from orthopedic operation

We report a case of pulmonary carcinosarcoma. Surgery is required for this rare mixed type, biphasic tumor. It is generally considered to be a malignant formation issuing from a single cell line but with a two-way differentiation into epithelial and conjunctive components. There is a differentiation continuum between spindle-cell carcinomas (also called monophasic sarcomatoid carcinoma) and carcinosarcoma (or biphasic sarcomatoid carcinoma) leading to debate concerning the immunohistochemical and ultrastructural features.     

Fungal carriage in lizards

The occurrence of fungi was investigated in the gut of 200 common garden lizards (Agama agama). The most important pathogenic fungus isolated was Basidiobolus haptosporus, an aetiological agent of subcutaneous zygomycosis. It was recovered from the intestinal contents of 112 (56%) lizards. Other important fungi isolated included Aspergillus spp. in 24 (12%) lizards, Candida spp. in 12 (6%), Penicillium spp. in 12 (6%) and Fusarium spp. in 12 (6%). Mucor spp. were isolated from eight (4%) male lizards only. Agamid lizards are plentiful in rural and urban areas of Nigeria. As they live in close vicinity to man, they are likely to play an important role in the spread of disease that may be caused by these fungi and its transmission to man. None of the animals investigated that yielded fungal cultures revealed any external fungal infection.     

实炉底节能连续式加热炉

轧钢生产使用实炉底连续式加热炉加热钢坯，炉内双纵滑管用耐热耐高温材料，无水冷，起到节约水、电的作用，达到节能增效的目的。     

PMMA／PBA乳胶IPN阻尼材料的研究

用乳液聚合方法合成了一系列的互穿聚合物网络，其中包括：ＰＭＭＡ／ＰＢＡ和Ｐ（ＭＭＡ－ｃｏ－ＰＭＡ）／ＰＢＡ乳胶互穿聚合物网络（ＬＩＰＮ），ＰＭＭＡ／ＰＢＡ乳胶双向互穿聚合物网络（ＬＢＩＰＮ）以及ＰＭＭＡ／ＰＢＡ界面交联互穿聚合物网络（ＩＣＬＩＰＮ）。动态力学谱和拉伸试验结果表明：（１）ＰＭＭＡ／ＰＢＡ互穿聚合物网络的两组分相容性和阻尼性能可通过ＭＭＡ和ＰＭＡ共聚来改善；（２）双向互穿技术是一种行之