Residual stress and plastic strain analysis in the brazed joint of bonded compliant seal design in planar solid oxide fuel cell

This paper uses finite element method (FEM) to predict the residual stress and plastic strain in the brazed joint of sealing foil-to-window frame in bonded compliant seal (BCS) design in a planar solid oxide fuel cell (PSOFC). The effects of window frame material type, sealing foil thickness, filler metal thickness and window frame thickness on residual stress and plastic strain are discussed. Large residual stress is generated in the joint, and the stress and strain are concentrated around the fillet. It is proved that the BCS design can mitigate and trap some residual stress by plastic deformation within the sealing foil. The residual stress and the ability of trapping stress of sealing foil are affected by window frame material and structure thickness. Based on the comprehensive considerations of the impact of residual stress and plastic strain, Alloy 625 as a window frame material is found to be better than Haynes 214, Hastelloy X and SUS 316L. The optimum thickness of sealing foil and filler metal BNi2 are found to be 150 μm and 75 μm, respectively. The residual stress and plastic strain are increased with the increase of window frame thickness.     

Recycle effect on heat transfer enhancement in double-pass parallel-plate heat exchangers under asymmetric wall fluxes

A new design of conjugated heat transfer in double-pass parallel-plate laminar countercurrent operations subjected to asymmetric wall heat fluxes has been investigated theoretically, and the analytical results obtained with superposition model which introduces the an eigenfunction expansion in terms of power series for the homogeneous part and an asymptotic solution for the inhomogeneous part. The influences of the design parameters, the impermeable-sheet position (Δ), and the operating parameters, the mass-transfer Graetz number (Gz), wall heat flux ratio (Q_r) and recycle ratio (R), are examined. The results are represented graphically and compared with those in a single-pass parallel-plate heat exchanger (without inserting an impermeable sheet). Considerable improvement in heat transfer is obtainable by employing such a recyclic double-pass device, instead of using the single-pass one. A technical feasibility of the new double-pass device was investigated in terms of the Nusselt number and device performance improvement under the effect of variable ratio of heat fluxes on both sides. It concluded that a substantial heat-transfer efficiency improvement is achieved by employing such a recyclic device with suitable elections of impermeable-sheet position and recycle ratio.     

Impact of dilute acid pretreatment on the structure of bagasse for bioethanol production

Dilute acid pretreatment is a commonly used pretreatment method in the course of producing bioethanol from lignocellulosics and the structure variation of the lignocellulosics is highly related to the pretreatment process. To understand the impact of dilute acid pretreatment on the structure of bagasse, four different pretreatment conditions by varying heating time are considered where the bagasse and the pretreated materials are examined using a variety of analysis methods. The obtained results indicate that the thermogravimetric analysis (TGA) is able to provide a useful insight into the recognition of lignocellulosic structure. Specifically, the peak of the TGA of the pretreated materials moves toward the low temperature region, revealing that the lignocellulosic structure is loosened. However, the characteristic of crystal structure of cellulose remains in the pretreated materials. Increasing heating time enhances the pretreatment procedure; as a result, the average particle size of the investigated materials increases with heating time. This swelling behavior may be attributed to the enlarged holes inside the particles in that the surface area decreases with increasing heating time. In addition, when the heating time is increased to a certain extent (e.g. 15 min), some fragments are found at the surface and they tend to peel off from the surface. It follows that the dilute acid pretreatments have a significant effect on the bagasse structure. Copyright © 2009 John Wiley & Sons, Ltd.     

九江长江干流江岸赤心堤段高压喷射灌浆施工

介绍了江西省九江长江干流江岸赤心堤段高压喷射灌浆设计与施工,并对高喷灌浆效果进行了评价,分析资料表明高喷灌浆达到了预期的良好效果,所采用的施工工艺合适可行。     

接触氧化-强化混凝法处理低温城镇污水

试验主要研究了低温条件下,接触氧化-强化混凝联合工艺对城镇污水的处理效果.结果表明;当进水平均温度低于12 ℃,CODCr 130～320 mg/L,氨氮20～45 mg/L,TP 2～4.5 mg/L时,其去除率分别可达到88%、70%、95%,出水可达到《城镇污水处理厂污染物排放标准》(GB18918-2002)一级B标准.强化混凝工艺能有效改善低温对接触氧化工艺造成的影响.     

Differential roles of T cell receptor alpha and beta chains in ligand binding among H-2Kd-restricted cytolytic T lymphocyte clones specific for a photoreactive Plasmodium berghei circumsporozoite peptide derivative

To study the interaction of T cell receptor with its ligand, a complex of a major histocompatibility complex molecule and a peptide, we derived H-2Kd-restricted cytolytic T lymphocyte clones from mice immunized with a Plasmodium berghei circumsporozoite peptide (PbCS) 252-260 (SYIPSAEKI) derivative containing photoreactive Nepsilon-[4-azidobenzoyl] lysine in place of Pro-255. This residue and Lys-259 were essential parts of the epitope recognized by these clones. Most of the clones expressed BV1S1A1 encoded beta chains along with specific complementary determining region (CDR) 3beta regions but diverse alpha chain sequences. Surprisingly, all T cell receptors were preferentially photoaffinity labeled on the alpha chain. For a representative T cell receptor, the photoaffinity labeled site was located in the Valpha C-strand. Computer modeling suggested the presence of a hydrophobic pocket, which is formed by parts of the Valpha/Jalpha C-, F-, and G-strands and adjacent CDR3alpha residues and structured to be able to avidly bind the photoreactive ligand side chain. We previously found that a T cell receptor specific for a PbCS peptide derivative containing this photoreactive side chain in position 259 similarly used a hydrophobic pocket located between the junctional CDR3 loops. We propose that this nonpolar domain in these locations allow T cell receptors to avidly and specifically bind epitopes containing non-peptidic side chains.     

The Global Exponential Stability of a Dynamical System for Solving Variational Inequalities

Networks and Spatial Economics - We revisit a dynamical system for solving variational inequalities. Under strongly pseudomonotone and Lipschitz continuous assumptions of the considered operator,...     

ZnO·2.7Al2O3 nanocomposite with high optical transparency

Here we report a transparent dual-phase ZnO·2.7Al₂O₃ ceramic. The composite is pore-free and consists of thin nanosheets with a spinel phase and a hexagonal phase, while the two phases match closely in both lattice and refractive index. Such features result in excellent optical transmittance (maximum value >80% in the visible spectrum) at comparable phase volume. This work may provide a new thought for the rational structural design of optical nanocomposites.     

Anthocyanin-fortified konjac glucomannan/sodium alginate composite edible boba: characteristics of texture,microstructure, in vitro release behaviour and antioxidant capacity

Konjac glucomannan/sodium alginate composite edible boba (KGM/SA-boba) with good taste is very popular in China, and it is an outstanding carrier for health potential ingredients. In this work, KGM/SA-boba were fortified with 0.25, 0.50, 0.75 and 1.00% purple sweet potato anthocyanin (PSPA), then characterised by the water distribution, texture, microstructure, in vitro release property of PSPA and antioxidant capacity. LF-NMR analysis demonstrated that the free water of KGM/SA-boba could transfer to tightly bound water with the addition of PSPA that made it with better water-binding ability, higher springiness and lower hardness. And the results of SEM and rheology showed that PSPA could stabilise the microstructure of KGM/SA-boba by forming more amorphous regions and hydrogen bonds proved by the results of DSC and FT-IR. Furthermore, 50% of PSPA in PSPA-fortified KGM/SA-boba can be released at the first hour in a simulated gastrointestinal environment. And the scavenging capacity of DPPH and ABTS of the PSPA-fortified KGM/SA-boba after digestion was higher than that of PSPA alone. Generally, PSPA could improve the texture while KGM/SA-boba in turn would make PSPA more stable in the gastrointestinal digestive system.