Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

Effect of anisotropy of tin on thermomechanical behavior of solder joints

Properties of body centered tetragonal tin are highly anisotropic. As a consequence large stresses can develop at the tin grain boundaries due to coefficient of thermal expansion mismatch during temperature excursions. A modeling approach to evaluate the 3D stress states that develop at grain boundaries during thermomechanical fatigue in tin-based solder is presented. Development of significant amounts of stresses in the plane of the grain boundary can cause grain-boundary sliding and surface-relief effects, while those normal to the grain boundary can cause grain-boundary decohesion and cracking.     

理想九点五态控制器原理的叙述

用计算的方式叙述理想九点五态控制器的控制原理。为便于人们理解二阶对象的运动中控制的变化过程,将抽象的对象转换为人们熟知的L-R-C电路,通过调节输入电压(即控制作用)的大小和方向来实现对对象性能的调节,并使系统达到理想的性能指标。最后用仿真来验证计算结果的正确性。     

An intelligent web-page classifier with fair feature-subset selection

The explosion of on-line information has given rise to many manually constructed topic hierarchies (such as Yahoo!!). But with the current growth rate in the amount of information, manual classification in topic hierarchies results in an immense information bottleneck. Therefore, developing an automatic classifier is an urgent need. However, classifiers suffer from enormous dimensionality, since the dimensionality is determined by the number of distinct keywords in a document corpus. More seriously, most classifiers are either working slowly or they are constructed subjectively without any learning ability. In this paper, we address these problems with a fair feature-subset selection (FFSS) algorithm and an adaptive fuzzy learning network (AFLN) for classification. The FFSS algorithm is used to reduce the enormous dimensionality. It not only gives fair treatment to each category but also has ability to identify useful features, including both positive and negative features. On the other hand, the AFLN provides extremely fast learning ability to model the uncertain behavior for classification so as to correct the fuzzy matrix automatically. Experimental results show that both FFSS algorithm and the AFLN lead to a significant improvement in document classification, compared to alternative approaches.     

Influence of iron oxide pigments on the properties of concrete interlocking blocks

Concrete interlocking blocks (CIBs) are utilized in a variety of commercial, municipal, and industrial applications. Superior engineering properties, low maintenance, ease of placement and removal, reuse of original blocks, aesthetic appeal, and immediate availability are the primary reasons for choosing concrete block pavement over other paving surfaces. It is a common practice to pigment building materials, such as mortar, concrete pavers, concrete roof tiles, and prefabricated concrete products; CIBs are colored using iron oxide pigments. This article presents experimental results detailing the properties of CIBs dyed with pigments. The results of these experiments are as follows: Because the particles of iron oxide pigments are finer than those of brown iron oxide, interlocking blocks mixed with the former acquired higher color strength than with the latter. Additional analysis determined a definite relationship between the flexural strength and the absorption ratio of pigment-dyed blocks; the correlation coefficient (R²) of interlocking blocks at 91 days was .90. It is suggested that if iron oxide pigments are to be used to color CIBs, the pigment-to-cement ratio should be below 4%.     

Transmission performance of 10-Gb/s 1550-nm transmitters using semiconductor optical amplifiers as booster amplifiers

We have demonstrated the transmission performance of 10-Gb/s transmitters based on LiNbO/sub 3/ modulator using semiconductor optical amplifiers (SOAs) as booster amplifiers. Utilizing the negative chirp converted in SOAs and self-phase modulation induced by high optical power, we can successfully transmit 10-Gb/s optical signals over 80 km through the standard single-mode fiber with the transmitter using SOAs as booster amplifiers. SOAs can be used for booster amplifiers with a careful adjustment of the operating conditions. In order to further understand an SOA's characteristics as a booster amplifier, we model SOAs and other subsystems to verify the experimental results. Based on the good agreement between the experimental and simulation results, we can find the appropriate parameters of input signals for SOAs, such as extinction ratio, rising/falling time, and chirp parameter to maximize output dynamic range and available maximum output power (P/sub o,max/).     

Formation of a geometric pattern with a mobile wireless sensor network

Mobile wireless sensor networks (MWSNs) will enable information systems to gather detailed information about the environment on an unprecedented scale. These self‐organizing, distributed networks of sensors, processors, and actuators that are capable of movement have a broad range of potential applications, including military reconnaissance, surveillance, planetary exploration, and geophysical mapping. In many of the foreseen applications, the MWSN will need to form a geometric pattern without assistance from the user. In military reconnaissance, for example, the nodes will be dropped onto the battlefield from a plane and land at random positions. The nodes will be expected to arrange themselves into a predetermined formation in order to perform a specific task. Thus, we present algorithms for forming a line, circle, and regular polygon from a given set of random positions. The algorithms are distributed and use no communication between the nodes to minimize energy consumption. Unlike past studies of geometric problems where algorithms are either tested in simulations where each node has global knowledge of all the other nodes or implemented on a small number of robots, the robustness of our algorithms has been studied with simulations that model the sensor system in detail. The simulations demonstrate that the algorithms are robust against random errors in the sensors and actuators. © 2004 Wiley Periodicals, Inc.     

镍层耐硝酸腐蚀性测试——一种简单的预先探测ENIG镍层“黑盘”现象的测试方法

随着更加精细的SMT、BGA等表面贴装技术的运用,化学沉镍金(ENIG)作为线路板最终表面处理得到了越来越广泛的应用,同时可怕的“黑盘”现象也随之更广泛地“流行”起来,直接导致贴装后元器件焊接点不规则接触不良。为了贯彻执行最好的流程控制和采取有效的预防措施,了解这种焊接失败的产生机理是非常重要的,及早的观测到可能发生“黑盘”现象的迹象变得同样关键。本文介绍了一种简单的预先探测ENIG镍层“黑盘”现象的测试方法-镍层耐硝酸腐蚀性测试,这种测试可以用于作为一种常规的测试方法监测一般化学沉镍溶液在有效使用寿命范围内新鲜沉积的镍层的质量。利用Weibull概率统计分析在不同的金属置换周期(MTO)下镍层的可靠性能表现。结合试验结果得出了一个镍层耐硝酸腐蚀性的判定标准。     

Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003