Modified determination of 2-thiobarbituric acid value in fats and oils

Several methods for the determination of TBA-value were compared with a new direct modification (omitting the previous distillation), using 1-butanol as the sole solvent. The absorbance is measured at 530 nm after heating to 95 degrees C for 120 min, and cooling. The effect of variables was tested by the Youdens ruggedness test (reaction time, temperature, cooling, concentration of sample, thiobarbituric acid, water, heavy metals, antioxidants, chelating agents, bubbling with oxygen or nitrogen). The Lambert-Beers law is valid in the absorbance range between 0.05 and 0.8. The repeatability is better than that of the Dzikowskis procedure and comparable with those of more complicated distillation methods. The standard deviation is in a linear relation with the absorbance (range 0.1-1.0). The method was found satisfactory for evaluating lard, cooking fat, soybean, sunflower, and rapeseed oils in the stage of beginning rancidity.     

Mechanical improvement of hydroxyapatite by TiO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> nanoparticles deposition

Deposition of Ti was carried out by laser ablation onto hydroxyapatite porous discs in an Ar atmosphere. Ti nanoparticles were deposited onto HAp surface in order to modify its roughness and morphology as it is observed by scanning electron microscopy (SEM) and scanning probe microscopy (SPM). A homogeneous distribution of Ti over the disc surface was corroborated by elemental mapping. A comparison of the hydroxyapatite hardness before and after deposition was performed using SPM nanoindentation. Transmission Electron Microscopy (TEM) showed that the Ti nanoparticles obtained were covered by an oxygen shell. It is shown that surface modifications of the covered HAp by Ti result in better mechanical properties, reducing the possible damage to the HAp ceramic by friction or impacts as it often happens in meniscus, bone junctions and the inclusion of prosthesis for human treatments.     

Low temperature and strain rate dependence of fracture stress and fracture toughness on thin Fe40Ni40B20 amorphous ribbon

The fracture stress and the critical stress intensity factor of the Fe₄₀Ni₄₀B₂₀ amorphous metallic ribbons 20 μm thick were measured in the temperature range 4.2–300 K and at deformation rates from 3.3×10⁻⁶ to 1.25×10⁻³ m⁻¹ with the aim to obtain more information on the condition for the onset and development of the inhomogeneous plastic deformation and fracture.     

Efficient and accurate approach for powder compaction problems

 In this paper, a new approach for powder cold compaction simulations is presented. A density-dependent plastic model within the framework of finite strain multiplicative hyperelastoplasticity is used to describe the highly nonlinear material behaviour; the Coulomb dry friction model is used to capture friction effects at die-powder contact; and an Arbitrary Lagrangian–Eulerian (ALE) formulation is used to avoid the (usual) excessive distortion of Lagrangian meshes caused by large mass fluxes. Several representative examples, involving structured and unstructured meshes are simulated. The results obtained agree with the experimental data and other numerical results reported in the literature. It is shown that, contrary to other Lagrangian and adaptive h-remeshing approaches recently reported for this type of problems, the present approach verifies the mass conservation principle with very low relative errors (less than 1% in all ALE examples and exactly in the pure Lagrangian examples). Moreover, thanks to the use of an ALE formulation and in contrast with other simulations, the presented density distributions do not present spurious oscillations. Received: 20 March 2002 / Accepted: 15 October 2002 The partial financial support of the Ministerio de Ciencia y Tecnología (grant number DPI 2001-2204) is gratefully acknowledged.     

Microstructural and textural characterization of a hot-rolled IF steel

The present paper reports the experimental results on the microstructural and textural characterization of a hot-rolled IF steel. The IF steel was hot-rolled in multiple passes in the austenitic field (1,070 °C) followed by air-cooling. SEM, TEM, and LOM were used to image the microstructure of the material. The global texture was determined by X-ray diffraction (XRD) technique. The mesotexture of selected regions was investigated by electron backscatter diffraction (EBSD). Results show the presence of a diffuse (nearly random) and weak texture in the hot-band that consists of recrystallized polygonal grains and subgrains. The fraction of boundaries with misorientations comprised in the interval 2° ≤ ψ < 15° was found to be lower than 5%. It can be concluded that these low angle boundaries and the presence of subgrains can be associated to the existence of a few areas softened by recovery during or after hot rolling in austenitic field.     

Synthesis and characterization of poly(N-propionyl)iminoethylene

Summary The cationic polymerization of 2-ethyl-2-oxazoline using CH₃I as initiator at different monomer/initiator ratios, temperatures, solvents and times of polymerization was carried out. The effect of these variables on the polymerization yield and viscosity of the polymers was studied. The poly(N-propionyl)iminoethylene was hydrolyzed in acid medium obtaining a linear poly(ethyleneimine) (PEI). All the polymers were characterized by elemental analysis, IR,¹H NMR, and¹³C NMR spectroscopy.     

The opening speech by Dr. Carlos Dotres Martínez. International Course on Dengue and Hemorrhagic Dengue in the Americas, Instituto de Medicina Tropical "Pedro Kourí", 14 August 1995

The authors report one case of multiple bilateral hydatid cyst of kidney associated to brain and spleen localizations, after intra cardiac rupture. They point out the rarity of the bilateral kidney localization of hydatidosis, explain the dissemination mode, and stress the role of computed tomography for the pre-operative diagnosis. The treatment is above all surgical and adapted to each case. The post-operative results are satisfying. Complementary medical treatment could be useful.