Impedance, attenuation and power-handling characteristics of doubleL-septa waveguides

Rectangular waveguides with two L-shaped septa attached to the broad walls in antipodal configuration have been shown theoretically by the authors (see ibid. vol.40, no.4, p.777-781, 1992) to be an improved variant of the double T-septa guide having larger cut-off wavelength and broader bandwidth of the dominant TE mode. Numerical data on the attenuation, impedance, and power handling capability of this new type of broadband guide are presented as additional design information     

An asymmetric line-axis compound parabolic concentrating single basin solar still

An asymmetric line-axis compound parabolic concentrating single basin solar still of concentration 1.15, exit aperture 0.24 metres and length 0.48 metres, 30° inclination and 60° half acceptance angle has been designed fabricated and tested.     

Design and performance of large low-cost solar water heating systems

An analysis is presented for the monthly performance evaluation of a simple design low cost solar water heating systems. A sample of typical results is presented which confirms their suitability as solar heating systems for summer peacking or as solar preheaters for year around loads.     

Crystallization of glass in fireclay refractories; part III: Detailed study on the mullite crystal size in the ‘synthetic’ glass

Poor-grade fireclay products contain substantial amount of glass. A glass of similar composition was synthesized, nucleated and heat-treated for crystallization of mullite. The size and size-distribution of mullite crystals, the rate of change of size and the aspect ratio of the crystals were investigated in relation to the nucleating agents and temperature.     

Transition metal joints for steam generators—An overview

The transition metal joint (TMJ) between an austenitic stainless steel and a chromium-molybdenum (Cr-Mo) ferritic steel used widely in steam generators of power plants has for a long time presented problems relating to premature failures in service. The direct (bimetallic) TMJ presently in use is designed for a service life of about 200,000 h; but such TMJs with iron-base weld metals have been failing in service within about one-third of their design lifetime, while their counterparts with nickel-base weld metals fail within about one-half of their design lifetime. The causes for such premature service failures of these TMJs are discussed in detail, leading to the development of improved TMJs. One of the improved TMJs with a trimetallic configuration of austenitic stainless steel/Alloy 800/Cr-Mo ferritic steel is discussed in detail, covering its development, characterisation and evaluation. Accelerated performance tests in the laboratory have indicated a four-fold improvement in the service life of the TMJ with this trimetallic configuration compared to the bimetallic configuration. The metallurgical details of these studies are also discussed in this paper.     

Minimal inhibition concentrations of selected antibiotics for strains of Staphylococcus aureus

Minimal inhibition concentrations (MIC) of gentamycin (Ge), neomycin (Neo), rifampicin (Rif), ampicillin (Amp), lincomycin (Lin), erythromycin (Ery), and streptomycin (STM) were determined by the agar dilution technique using 46, 130, 131, 125, 140, 139 and 142 strains of Staphylococcus aureus, respectively. The strains, selected from the collection of the authors' laboratory, were isolated from mammary gland secretions of cows affected with clinical or subclinical mastitis. The following ranges of MIC (micrograms/ml) were assessed for the antibiotics under study: Ge 0.125-0.50, Neo 0.06-0.50, Rif 0.0039-0.030, Amp 0.015-1.00, Lin 0.25-1.00, Ery 0.06-0.25, STM 0.50-64.0. Modal MIC (micrograms/ml) were as follows; Ery 0.125 (86%), Lin 0.5 (71.4%), Rif 0.007 (68.7%), Ge 0.25 (56.5%), STM 1.00 (54.2%), Neo 0.25 (53.8%), Amp 0.06 (41.6%). The order of efficiency expressed in MIC 90 (micrograms/ml) was as follows: Rif (0.015), Ery (0.125), Ge (0.25), Neo (0.25), Amp (0.5), STM (4.0).     

Analysis of aperture blockage in reflector antennas by usingobstacle-located blockage currents

An improved method is presented to account for blockage effects in the analysis of reflector antennas. Commonly this is done by introducing shadows on the reflector surface according to the location of the obstacles when performing the physical optics integration. By using physical optics blockage currents located at the blocking obstacle instead of at the main reflector surface, the effect of the different locations in the axial direction is accurately accounted for. This can easily be included by a single phase factor in existing computer programs based on physical optics integration     

New wire interface for graded 3-D TLM

A new 3-D graded TLM model for thin radiating wires is presented. The model differs from previous TLM models because the wire is modelled at the interfaces between cells, rather than through the centre of the node. The connection between the TLM symmetrical condensed-node link lines and the line forms a 'wire interface'. The scattering algorithm for the interface and simulation results are given.<>     

Organized media for fluorescence analysis of complex samples: comparison of bile salt and conventional detergent micelles in coal liquids.

Accurate quantitative determinations are often difficult to obtain from fluorescence analysis of complex samples due to sample matrix effects and intermolecular interactions between solutes. Organized media can be used to minimize these unwanted processes without physical separation or extraction of the analytes from the sample matrix by isolating the analyte molecules in a uniform microenvironment within the sample. The advantages of bile salt micellar media over conventional detergent micelles are demonstrated for analysis of coal liquids. The bile salt media is shown to increase the sensitivity and dynamic range of fluorescence measurements relative to simple ethanolic solutions, without promoting gound-state and excited-state interactions that occur in the detergent micellar media.