Mlcrolasers based on silica microspheres

Light can be confined efficiently in the high-Q, small-volume whispering-gallery-modes observed in silica microspheres. By coupling these microspheres to eroded optical fibers and fiber tips, direct mapping of the whispering-gallery modes has been achieved and the mode numbers have been assessed. The properties of these modes have allowed us to obtain laser action with very low thresholds in Nd-doped silica microspheres. Further projects in the field of non-linear optics and cavity quantum electrodynamics are described.     

On the Relation between Morphology and FET Mobility of Poly(3‐alkylthiophene)s at the Polymer/SiO2 and Polymer/Air Interface

The influence of the interface of the dielectric SiO₂ on the performance of bottom‐contact, bottom‐gate poly(3‐alkylthiophene) (P3AT) field‐effect transistors (FETs) is investigated. In particular, the operation of transistors where the active polythiophene layer is directly spin‐coated from chlorobenzene (CB) onto the bare SiO₂ dielectric is compared to those where the active layer is first spin‐coated then laminated via a wet transfer process such that the film/air interface of this film contacts the SiO₂ surface. While an apparent alkyl side‐chain length dependent mobility is observed for films directly spin‐coated onto the SiO₂ dielectric (with mobilities of ≈10^?3 cm² V^?1 s^?1 or less) for laminated films mobilities of 0.14 ± 0.03 cm² V^?1 s^?1 independent of alkyl chain length are recorded. Surface‐sensitive near edge X‐ray absorption fine structure (NEXAFS) spectroscopy measurements indicate a strong out‐of‐plane orientation of the polymer backbone at the original air/film interface while much lower average tilt angles of the polymer backbone are observed at the SiO₂/film interface. A comparison with NEXAFS on crystalline P3AT nanofibers, as well as molecular mechanics and electronic structure calculations on ideal P3AT crystals suggest a close to crystalline polymer organization at the P3AT/air interface of films from CB. These results emphasize the negative influence of wrongly oriented polymer on charge carrier mobility and highlight the potential of the polymer/air interface in achieving excellent “out‐of‐plane” orientation and high FET mobilities.     

Trust for Ubiquitous,Transparent Collaboration

In this paper, trust-based recommendations control the exchange of personal information between handheld computers. Combined with explicit risk analysis, this enables unobtrusive information exchange, while limiting access to confidential information. The same model can be applied to a wide range of mobile computing tasks, such as managing personal address books and electronic diaries, to automatically provide an appropriate level of security. Recommendations add structure to the information, by associating categories with data and with each other, with degrees of trust belief and disbelief. Since categories also in turn confer privileges and restrict actions, they are analogous to rôles in a Rôle-Based Access Control system, while principals represent their trust policies in recommendations. Participants first compute their trust in information, by combining their own trust assumptions with others' policies. Recommendations are thus linked together to compute a considered, local trust assessment. Actions are then moderated by a risk assessment, which weighs up costs and benefits, including the cost of the user's time, before deciding whether to allow or forbid the information exchange, or ask for help. By unifying trust assessments and access control, participants can take calculated risks to automatically yet safely share their personal information.     

Detection of Carbon Dioxide in Air Using Difference-Frequency Generation Based Infrared Spectrometer

Spectroscopic detection of carbon dioxide (CO₂) in ambient air was performed using a continuous-wave mid-infrared spectrometer based on difference-frequency generation in an AgGaS₂ crystal. Significant improvement in nonlinear optical frequency conversion efficiency was achieved by Gaussian beam optical design consideration. CO₂ concentration was determined from direct-absorption spectral measurement.     

14C labelling of lignins of normal and bm3 maizes for fermentation studies

[U-¹⁴C] phenylalanine (phe*) and [O¹⁴CH₃] sinapic acid (sin*) were infused into the cut ends of normal and bm3 maizes (anthesis stage) under or above the last node or at mid-internode, with or without the leaf, in light or in darkness. Radioactivity was measured in the organs, and in phenolic constituents of the cell wall and saponified residues of the bases and tops of the apical inter-node. In both maize genotype labelled under the node the radioactivity was distributed more evenly in the organs with sin* than with phe*. Infusion above the node and at mid-internode greatly increased radioactivity in the bases and tops, respectively. Removal of the leaf only slightly increased the radioactivity, mainly in the bases, and no clear-cut effect of darkness was observed. Phe* labelled the phenolic acids and the three lignin units, but the syringyl units of bm3 maize were only slightly labelled. Sin* specifically labelled the syringyl units, which represented the least condensed fraction of lignins. Both the native and labelled lignins were highly alkali soluble. There were differences in lignin biogenesis between the bases and tops, and between normal and bm3 maizes. The newly formed lignins were slightly different from the native lignins but had similar types of heterogeneity, with variations in the internode and between genotypes similar to those in native lignins. Provided due allowance is made for the distinguishing characteristics of newly formed lignins, the [¹⁴C-lignin] cell walls, which are strongly labelled on complementary structures, seem suitable model substrates for fermentation studies.     

Ligand‐Free Synthesis of Aluminum‐Doped Zinc Oxide Nanocrystals and their Use as Optical Spacers in Color‐Tuned Highly Efficient Organic Solar Cells

The color of polymer solar cells using an opaque electrode is given by the reflected light, which depends on the composition and thickness of each layer of the device. Metal‐oxide‐based optical spacers are intensively studied in polymer solar cells aiming to optimize the light absorption. However, the low conductivity of materials such as ZnO and TiO₂ limits the thickness of such optical spacers to tenths of nanometers. A novel synthesis route of cluster‐free Al‐doped ZnO (AZO) nanocrystals (NCs) is presented for solution processing of highly conductive layers without the need of temperature annealing, including thick optical spacers on top of polymer blends. The processing of 80 nm thick optical spacers based on AZO nanocrystal solutions on top of 200 nm thick polymer blend layer is demonstrated leading to improved photocurrent density of 17% compared to solar cells using standard active layers of 90 nm in combination with thin ZnO‐based optical spacers. These AZO NCs also open new opportunities for the processing of high‐efficiency color tuned solar cells. For the first time, it is shown that applying solution‐processed thick optical spacer with polymer blends of different thicknesses can process solar cells of similar efficiency over 7% but of different colors.     

Détermination des perturbations induites aux extrémités d’une ligne blindée soumise à une excitation ponctuelle de courant

This article allows the determination of the induced perturbations at the ends of the coaxial line in wide frequency band enough. The perturbation source is a current direct point injection into the cable screen in any position. For this, we have applied the theory of the state variables, with foundation of the quasi-TEM approximation, in order to simulate the coaxial line above a ground level that has a finished conductivity. This allows us to supply the current and voltage expressions at the ends of the line as their analytic forms for any conditions of charge. Next, the elaborate objective is to verify experimentally on concrete applications if the test obtained results confirm the theoretical expectations supplied by calculation code finalizing.     

Accurate surface potential determination in Schottky diodes by use of correlated current and capacitance voltage measurements. Application to n–InP

Based on current voltage (I-V_g) and capacitance voltage (C-V_g) measurements, a reliable procedure is proposed to determine the effective surface potential V_d.V_g/ in Schottky diodes. In the framework of thermionic emission, our analysis includes both the effect of the series resistance and the ideality factor, even voltage dependent. This technique is applied to n-type indium phosphide (n-InP) Schottky diodes with and without an interfacial layer and allows us to provide an interpretation of the observed peak on the C-V_g measurements. The study clearly shows that the depletion width and the flat band barrier height deduced from C-V_g, which are important parameters directly related to the surface potential in the semiconductor, should be estimated within our approach to obtain more reliable information.