Efficient performance analysis of asynchronous cellular CDMA overRayleigh-fading channels

The bit error rate (BER) analysis of a direct-sequence code-division multiple-access (DS-CDMA) cellular system over a Rayleigh-fading channel often results in complicated expressions even though the Gaussian approximation is applied. A combined probability density function (pdf) approach for the forward link and a mean-method technique for the reverse link are proposed to significantly reduce the computational complexity. The simplified BER expressions are derived and yield accurate results     

Effects of ternary additions on the thermoelastic martensitic transformation of NiAl

Nickel-rich β-NiAl alloys, which are potential materials for high-temperature shape-memory alloys, show a thermoelastic martensitic transformation, which produces their shape memory effect. However, the transformation to Ni₅Al₃ phase during heating of NiAl martensite can interrupt the reversible martensitic transformation; consequently, the shape memory effect in NiAl martensite might not appear after heating. The phase transformation process in binary Ni-(34 to 37)Al martensite was investigated by differential thermal analysis (DTA) method, and we found that the condition of reversible martensitic transformation was not the β → Ni₅Al₃ transformation, but rather the M → Ni₅Al₃ transformation occurring at 250 °C to 300 °C. Therefore, the transformation temperature of M → Ni₅Al₃ determined the highest operating temperature for the shape memory effect. For verifying the critical temperature, the phase transformation process was investigated for eight ternary Ni-33Al-X alloys (X=Cu, Co, Fe, Mn, Cr, Ti, Si, and Nb). Only Ti, Si, and Nb additions were found to be effective in dropping the M _s temperature, and they facilitated the shape memory effect in Ni-33Al-X alloys. In particular, the addition of Si and Nb raised the transformation temperature of M → Ni₅Al₃, a potentially beneficial effect for shape memory at higher temperatures. This article is based on a presentation made in the symposium entitled “Fundamentals of Structural Intermetallics,” presented at the 2002 TMS Annual Meeting, February 21–27, 2002, in Seattle, Washington, under the auspices of the ASM and TMS Joint Committee on Mechanical Behavior of Materials.     

Synthesis of ultrafine LiCoO2 powders by the sol-gel method

Ultrafine high-temperature (HT) LiCoO₂ powders were synthesized by the sol-gel method using polyacrylic acid (PAA) as a chelating agent. The decomposition process of the gel precursor was examined to determine the crystallization temperature and the dependence of the physicochemical properties of HT-LiCoO₂ powders on the PAA quantity was extensively investigated. Polycrystalline HT-LiCoO₂ powders, composed of very uniformly sized ultrafine particulates with an average particle size of 30–50 nm and a specific surface area of 2.3–17 m²g^–1, could be obtained at the lower calcination temperature of 550 °C and the shorter calcination time of 1 h compared to the solid-state reaction.     

共面转换液晶显示器中获得对比度高于1:600的新技术

薄膜晶体管液晶电视(TFT-LCD TV)因为具有薄、轻、紧凑和可随意放置的特点，已经占据了大部分电视机市场。除了这些物理特性以外，最重要的特性是已具有了良好像质的对比度。为了将对比度提高到1：600以上，对偏振片膜、背光源板、滤色片树脂、电极锥角和摩擦条件等都进行了研究。优化的背光板组合，光滑的电极锥角和摩擦方法的控制是提高对比度的主要控制因素。应用新开发的滤色片树脂，对获得高对比度最为有效。     

Nanoporous activated carbon cloth for capacitive deionization of aqueous solution

Activated nanostructured-carbon cloths with a high ratio of surface area to volume are used as electrode for capacitive deionization. The electrochemical properties on capacitive deionization for NaCl solution have been investigated to improve efficiency of capacitive deionization properties from aqueous solution, employing chemical surface-modification by etching in alkaline and acidic solution. The removal efficiency of inorganic salts of activated carbon cloths by chemical modification significantly increased. Specially the carbon cloth surface modified in HNO₃ showed an effect of improvement in the CDI efficiency due to not only ion adsorption by an electric double layer, but also electron transfer by Faradaic reaction.     

Study on Contamination Control for Yield Enhancement in the Manufacturing Line of Cellular Phone Modules

Practical studies on the method of contamination control for yield enhancement in the cellular phone modules production line were carried out. A contamination control method was proposed, consisting of data collection, data analysis, improvement action, verification, and implementation of control. The partition check method and the composition analysis for data collection and data analysis were respectively used in the cellular phone modules manufacturing process, and these methods were evaluated by the variation of yield loss before and after implementing the actions for improvement. In the partition check method, the critical process step was selected, and yield loss reduction through improvement actions was observed, whereas in the composition analysis, critical sources were selected, and yield loss reduction through improvement actions was investigated. From the results, it is concluded that the partition check and the composition analysis are effective solutions for contamination control in cleanroom production lines.     

Zero-valent iron treatment of RDX-containing and perchlorate-containing wastewaters from an ammunition-manufacturing plant at elevated temperatures.

The use of zero-valent iron for treating wastewaters containing RDX and perchlorate from an army ammunition plant (AAP) in the USA at elevated temperatures and moderately elevated temperature with chemical addition was evaluated through batch and column experiments. RDX in the wastewater was completely removed in an iron column after 6.4 minutes. Increasing the temperature to 75 degrees C decreased the required retention time to 2.1 minutes for complete RDX removal. Perchlorate in the wastewater was completely removed by iron at an elevated temperature of 150 degrees C in batch reactors in 6 hours without pH control. Significant reduction of perchlorate by zero-valent iron was also achieved at a more moderate temperature (75 degrees C) through use of a 0.2 M acetate buffer. Based on the evaluation results, we propose two innovative processes for treating RDX-containing and perchlorate-containing wastewaters: a temperature and pressure-controlled batch iron reactor and subsequent oxidation by existing industrial wastewater treatment plant; and reduction by consecutive iron columns with heating and acid addition capabilities and subsequent oxidation.     

Friction and wear of Inconel 690 and Inconel 600 for steam generator tube in room temperature water

In the steam generators of nuclear power plants, the flow of cooling water can cause the tubes to vibrate, resulting in fretting wear damage due to contacts between these tubes and their supports. The tubes are made of Inconel 690 and Inconel 600 and the supports are made of STS 304. In this paper, fretting wear tests in water were performed using the materials Inconel 690 and Inconel 600 in contact with STS 304. Fretting tests using a cross-cylinder type set up were conducted under various vibrating amplitudes and applied normal loads in order to measure friction forces and wear volumes. Also, conventional sliding tests using a pin-on-disk type set up were carried out to compare these test results.In the fretting tests, friction force was found to be strongly dependent on normal load and vibrating amplitude. Coefficients of friction decreased with an increase in the normal load and a decrease in the vibrating amplitude applied. Also, the wear of Inconel 600 and Inconel 690 was predicted using a work rate model. Depending on the normal load and vibrating amplitude applied, distinctively different wear mechanisms and often drastically different wear rates occurred. It was found that the fretting wear coefficients for Inconel 600 and Inconel 690 were 9.3×10⁻¹⁵ and 16.2×10⁻¹⁵ Pa⁻¹, respectively. This study shows that Inconel 690 can result in lesser friction forces and exhibits less wear resistance than Inconel 600 in room temperature water.     

Improved strained HEMT characteristics using double-heterojunctionIn0.65Ga0.35As/In0.52Al0.48As design

The DC and microwave properties of strained In_0.65Ga _0.35As/In₀₅₂Al_0.48As HEMTs (high electron-mobility transistors) with double-heterojunction design are presented. The high sheet carrier density and good carrier confinement give rise to excellent device performance with very low output conductance. For 1×150-μm² long-gate HEMTs, the measured cutoff frequency f_T and maximum frequency of oscillation f_max are as high as 37 and 66 GHz, respectively     

Simulation of polarization converter formed by poling-inducedpolymer waveguides

A polarization converter using electrooptic (EO) polymer waveguides is proposed and it is simulated by a full vectorial beam propagation method (VBPM) for anisotropic medium. First, an efficient structure of poling electrodes is proposed for the fabrication of TE-mode poling-induced waveguides in EO polymer. For given electrode structures of both TE-mode and TM-mode waveguides, poling-induced dielectric tensors are calculated by the finite-element method to provide refractive index distribution, data for VBPM simulation. It is shown numerically that the poled TE and TM mode waveguides work efficiently as the corresponding polarization filters. Then, new poling electrodes are suggested to fabricate a waveguide device formed by connecting the TE and TM mode waveguides adiabatically with a slowly varying structure. This waveguide device has the optic axis slowly rotating as one moves along the propagation direction, so that it will act as polarization converter. VBPM simulation shows that the polarization of the guided mode rotates following the optic axis distribution. Polarization conversion is demonstrated successfully with high conversion efficiency and low excess loss