High Gd Concentration GaGdN Grown at Low Temperatures

GaGdN layers were grown at temperatures below 300°C by radio-frequency plasma-assisted molecular beam epitaxy on sapphire substrates. GaGdN samples with high Gd concentration as high as 12.5% were obtained by lowering the growth temperature. X-ray diffraction results showed no obvious secondary phase, which means that the phase separation can be suppressed by the growth at low temperatures. All samples, including those grown at room temperature, showed ferromagnetic characteristics. Photoluminescence emission was observed, though spectra exhibit broad and sharp luminescence bands related to many kinds of defects. It is suggested that electrons coming from defects, especially, nitrogen vacancy, stabilize ferromagnetism, and that the carrier-induced ferromagnetism occurs in the low-temperature-growth GaGdN.     

Reduction kinetics of Fe<Subscript>2</Subscript>MoO<Subscript>4</Subscript> fine powder by hydrogen in a fluidized bed

Iron molybdate (Fe₂MoO₄) powders with an average particle size of 100 μm were reduced by hydrogen using a fluidized-bed batch reactor in the temperature range of 923 to 1173 K. The extent of the reaction was followed as a function of time by gas chromatography. The fluidizing-gas velocity was set at about 1.5 times the minimum fluidization velocity. The ratio of the height of the static bed to its diameter is about 1. Under the prevailing experimental conditions, it was found that the chemical reaction was the rate-controlling factor. The activation energy for this process was 158±17 kJ/mol. The crystal size of the Fe₂Mo powder produced at lower temperatures was in the nanometer range, indicating the possibility of mass production of alloys and intermetallics in the nanorange, using a fluidized bed.     

Calciothermic reduction of titanium oxide in molten CaCl<Subscript>2</Subscript>

Titanium oxides were reduced to metallic titanium using the liquid calcium floating on the molten CaCl₂. A part of Ca dissolved into CaCl₂ and reacted with TiO₂ settled below CaCl₂. The by-product CaO also dissolved by about 20 mol pct into CaCl₂, which was effective in reducing the oxygen concentration in the obtained Ti particles. The compositional region in the Ca-CaCl₂-CaO system was examined for the less oxygen contamination in Ti and the better handling in leaching. A large amount of the residual calcium oxidized the titanium powder in leaching. The metallic Ti powder less than 1000 mass ppm oxygen could be obtained only for 3.6 ks using 5 to 7 mol pct Ca-CaCl₂ at 1173 K. The powder was slightly sintered like sponge, and contained approximately 1500 ppm Ca. The anatase phae, the intermediate product in the refining process of TiO₂, could be also supplied as raw material as well as rutile.     

The electrochemical behaviour of nitrogen-containing austenitic stainless steel in methanolic solution

The corrosion behaviour of nitrogen-containing austenitic stainless steel in methanol containing different concentrations of H₂SO₄, HCl, LiCl and H₂SO₄ + HCl has been investigated using a potentiostatic polarization method. The cathodic reaction in the H₂SO₄, HCl and H₂SO₄ + HCl solutions was proton reduction whereas in the neutral LiCl solution, oxygen reduction was the predominant cathodic reaction. Active, passive and transpassive behaviours were observed only for higher concentrations of H₂SO₄ (0.01–2.0 M) due to the inherent water content. A cathodic loop, characterized by measured negative current in the anodic region, was also observed in solutions, in which the concentration of H₂SO₄ was 1.0 M or higher. The relative stability of the passive films decreased as the H₂SO₄ concentration increased, and thus the steel suffered from mild pitting corrosion. In the chloride environment, the rate of corrosion increased as the Cl⁻ ion concentration increased. The presence of acid along with Cl⁻ ions enhanced corrosion, and the corrosion rate increased significantly. The steel suffered from mild intergranular corrosion in acidic chloride solutions of methanol. In the H₂SO₄ + HCl solutions, passive films were only formed when the H₂SO₄ to HCl concentration ratio was greater than ∼10:1.     

Nanocrystalline Ni coatings strengthened with ultrafine particles

In this study, nanocrystalline Ni powders and thermally sprayed coatings, containing ultrafine AlN particles, were synthesized and characterized. The results indicated that the presence of AlN particles in the powders drastically decreased the dimension of agglomerates formed by cryomilling and increased the surface roughness of the agglomerates. The AlN phase was broken down into ultrafine particles of approximately 30 nm in size. These particles were dispersed in the Ni matrix and enhanced the development of a nanocrystalline structure in the Ni matrix during cryomilling. Selected-area diffraction patterns, obtained from transmission electron microscopy (TEM) and X-ray mapping with scanning electron microscopy (SEM), confirmed the presence of AlN particles in the coatings. The presence of AlN particles also led to an increase in the amount of NiO phase that was distributed in the coating, in the form of ultrafine, round particles. AlN particles increased the microhardness of the Ni coating by approximately 60 pct. Indentation-fracture results also indicated that the fine, dispersed AlN particles raised the apparent toughness of the Ni coating. The synthesized Ni coatings containing ultrafine AlN particles were characterized as equiaxed nanocrystalline grains with an average size of 24 nm, in which twins were observed. The increase in microhardness resulted from both grain refinement and the presence of ultrafine particles. The latter played the primary role in strengthening.     

Microstructure and fatigue characteristics of direct chill cast and electromagnetic cast 2024 Al alloy ingots

The distinct advantages of the electromagnetic casting (EMC) process consist in the presence of stirring motions in the melt, which lead to significant grain size reduction in solidified ingot. Furthermore, surface and subsurface qualities are improved due to the absence of ingot mold. However, it is impossible to achieve the aforementioned advantages in conventional direct chill casting (DCC). In order to contrast the before and after heat treatments of the microstructural and mechanical characteristics of EMC and DCC 2024 aluminium alloys, optical microscopy, scanning electron microscopy, transmission electron microscopy (TEM), X-ray diffractions (XRD), differential scanning calorimetry (DSC), etc. were carried out. Compared with the DCC ingot, the EMC ingot has better mechanical properties not only in the ascast condition but also in the as-aged condition. The DSC curves show that the EMC specimens have high enthalpy, i.e., the thermal kinetic energy to form precipitates during the aging treatment process. Despite heat treatments applied to the DCC ingot, it fails to attain the same mechanical properties as the EMC ingot. Moreover, considering the expernsive scalping operation for DCC ingots, the EMC technique, which offers a lower manufacturing cost, is one of the best manufacturing methods used in obtaining the ingots of wrought aluminum alloys.