Hydrodynamic characteristics of a FCC regenerator

The hydrodynamic and gas mixing characteristics have been determined in a FCC regenerator (0.48 m I.D.x3.4 m high) with FCC particles. Solids holdup in the dense bed decreases with increasing gas velocity, but it increases in the freeboard region. The bubble/void fraction increases with an increase along the bed height at a given gas velocity and increases with increasing gas velocity at a constant bed height. Backmixed tracer gas at the wall region is higher than that at the center region of the bed. The gas backmixing coefficient decreases with increasing gas velocity.     

Universal yield stress function for biocompatible chitosan based-electrorheological fluid: Effect of particle concentration

Electrorheological (ER) response of biocompatible particles suspended in an insulating silicone oil, was investigated under several different applied external electric field strengths. Chitosan, a biodegradable polysaccharide, was used as anhydrous ER materials. The effect of particle volume concentration on their ER response was examined by focusing on the measurement for rheological and electrical properties. The yield stress of chitosan suspended in silicone oil system as a function of applied electric field strength showed different value of slopes for different particle concentrations, however, all data points collapse onto a universal scaling function.     

A visual study on flame behavior in tone-excited non-premixed jet flames

A visualization study on the effect of forcing amplitude in tone-excited jet diffusion flames has been conducted. Visualization techniques are employed using optical schemes, which are a light scattering photography. Flame stability curve is attained according to Reynolds number and forcing amplitude at a fuel tube resonant frequency. Flame behavior is globally grouped into two from attached flame to blown-out flame according to forcing amplitude; one sticks the tradition flame behavior which has been observed in general jet diffusion flames and the other shows a variety of flame modes such as the flame of a feeble forcing amplitude where traditionally well-organized vortex motion evolves, a fat flame, an elongated flame, and an in-burning flame. Particular attention is focused on an elongation flame, which is associated with a turnabout phenomenon of vortex motion, and on a reversal of the direction of vortex roll-up. It is found that the flame length with forcing amplitude is the direct outcome of the evolution process of the formed inner flow structure. Especially the negative part of the acoustic cycle under the influence of a strong positive pressure gradient causes the shapes of the fuel stem and fuel branch part and even the direction of vortex roll-up to dramatically change.     

Effect of Antimony Addition on Electrical and Optical Properties of Tin Oxide Film

Antimony-doped tin oxide films were prepared on Corning glass substrate by chemical vapor deposition from a gas mixture of SnCl₄–SbCl₅–H₂O. The electrical conductivity and optical transmission of tin oxide films were studied with antimony doping. The film conductivity increased largely without losing optical transparency with a small addition of antimony. The increase of the conductivity was attributed mainly to more electrons donated by pentavalent Sb ions in the SnO₂ lattice. Large additions of antimony, however, diminished the conductivity, optical transparency, and crystallinity of the film. The diminution was found to be caused by fine Sb₂O₅ phases codeposited with SnO₂.     

Diffusional interference in liquid phase counter-adsorptions

A surface diffusion mocel with diffusional interference has been presented for the analysis of multicomponent adsorption of phenols by activated carbon. Surface diffusion coefficients for multicomponent adsorptions were estimated from the relationship between. the surface diffusion coefficient of each species and the surface coverage. The diffusional interference coefficients, W_ij, was determined from experimental counter-adsorption data. The numerical values of W_ij were in the range of 0.4–0.9, which show that the introduction of diffusional interference is necessary to analyze multicomponent counter-adsorptions properly. The proposed model successfully simulates the behaviour of phenols-activated carbon system in a batch adsorber.     

Highly Efficient Overall Water Splitting Through Optimization of Preparation and Operation Conditions of Layered Perovskite Photocatalysts

The layered perovskite materials were found to give the high photocatalytic activity in water splitting reaction under UV irradiation, where the electronic structure of perovskite slab constructing the layered structure (the total cation valency) was the most crucial factor to the high photocatalytic activity. Both the excessive cation valency and the layered structure were required for active photocatalysts, while the slab thickness of layered perovskites had an insignificant effect on water-splitting activity. In order to identify key variables that affected photocatalytic activity and to optimize the performance of (110) layered perovskite, La₂Ti₂O₇ was modified by various methods. The optimum amount of loaded nickel had a great effect and the amount depended on the surface area of the perovskite phase. When an alkaline-earth element such as Ba, Sr, and Ca was doped on La₂Ti₂O₇, the photocatalytic activity was enhanced markedly. Introduction of an alkaline hydroxide into the reaction system as an external additive enhanced the activity further showing extremely high quantum yields close to 50%.     

Defect detection using feature point matching for non-repetitive patterned images

Defect detection is an important technology for the quality control in the production process of wafer, TFT-LCD and PCB. Inspection is performed using the finished product’s image. The images are classified into two different groups—images with a repetitive pattern on a regular cycle and images without a repetitive pattern. A standard object for comparison is required, because manual defect detection is not possible for areas without repetitive patterns. In such areas, defect detection occurs through contrasting a reference pattern to the pattern being inspected. Methods of inspection using reference image have been researched but have limitations due to their requirement of precise alignment of the images. This paper proposes a method of defect detection to overcome such limitation using feature point matching. Feature points are extracted using a corner detector and detects defect by finding a correspondence between two feature point sets. Performance of the proposed method is evaluated by using Wafer SEM images and compared with conventional methods. Experiment results demonstrate the proposed method achieves higher detection accuracy than conventional methods and is less sensitive to alignment error and noise.     

Humidity‐sensitive properties of new polyelectrolytes based on the copolymers containing phosphonium salt and phosphine function

A simple strategy was developed based on a new reactive function‐ and a salt‐containing new monomer, 4‐vinylbenzyl dimethyl 2‐(dimethylphosphino)ethyl phosphonium chloride (VDEPC), to obtain stable humidity‐sensitive membranes. The major ingredient of a humid membrane is crosslinked polyelectrolytes obtained from copolymers of VDEPC/2‐ethylhexyl acrylate (2‐EHA) = 1/0, 4/1, and 2/1. Isothermal humidity absorption experiments were performed for the estimation of humidity‐sensing materials. The crosslinked copolymers prepared from the reaction of VDEPC/2‐EHA = 4/1 with 1,4‐dichlorobutane showed an average impedance of 595, 39.1, and 3.9 KΩ at 30, 60, and 90% RH, respectively. Their hysteresis, temperature dependence, frequency dependence, and response time were measured. The reliability including water resistance and a long‐term stability were estimated for the application of the common humidity sensor. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1062–1070, 2003     

Synthesis and properties of acrylonitrile-CR-methyl methacrylate graft copolymer

Graft copolymerization of acrylonitrile (AN) and methyl methacrylate (MMA) onto polychloroprene (CR) was carried out using benzoyl peroxide as initiator. The effects of mole ratio of AN to MMA, reaction temperature, reaction time, solvent, and initiator concentration on the graft copolymerization were examined. It was found that the thermal stability and weatherability of the AN—CR—MMA graft copolymer (ACM) were considerably better than those of CR.