热声制冷机及其改进实验研究

热声制冷作为一种很有前途的制冷方法，在国内外相关领域引起了极大兴趣。热声制冷机由声发生器、共振管、板叠及高、低温换热器等部分组成。对声驱动器的振动膜及其冷却系统、气体弹簧系统、高、低温换热器进行了初步改进，使制冷机冷端温降从原来的12℃提高到27℃左右，这是目前国内报道的最大温降。     

用MATLAB进行三相交-交变频电源的仿真设计

三相交－交变频电源在低频拖动控制中有广泛的应用，通过晶闸管设计的静止式变频电源具有效率高，无噪声的优点，但却存在设计复杂、成本高，高速困难等缺点，而利用MATLAB软件中的Simlink仿真工具来实现三相交－交变频电源的仿真设计和分析，能做到省时，省成本，易于操作，在静止式变频电源设计中有很好的使用价值。采用MATLAB仿真工具完成了一个全数字控制的三相交－交变频电源的设计。     

水力脉动冲击钻井工具初步研究与试验

掘力脉动冲击钻井是将水力脉冲、机械冲击振动结合为一体提高钻井速度的一种方法，介绍了辽河油田研制的脉动冲击钻井工具的结构、工作原理及现场试验情况。在潜山混合花岗岩、砂岩，硬脆性泥岩等不同地层的现场试验表明：水力脉动工具工作平稳，未出现蹩跳钻现象，也没有出现脱、落、断、掉等问题，主体安全性、可靠性较好；在潜山混舍花岗岩、砂岩、硬脆性泥岩地层机械钻速提高幅度较大，但在部分泥岩地层效果不佳。试验中发现密封圈耐温性差、脉冲腔易磨损等问题，并据此提出了水力脉动冲击工具的下一步研究方向。     

Effects of surface roughness of substrates on the c-axis preferred orientation of ZnO films deposited by r.f. magnetron sputtering

The c-axis preferred orientation of ZnO film is the most important factor for its successful application in piezoelectric devices. The effects of surface roughness of the substrate on the c-axis preferred orientation of ZnO thin films, deposited by radio frequency magnetron sputtering, were investigated. During sputtering, the oxygen content in the argon environment used was varied from 0 to 70% at a total sputtering pressure of 10 mTorr. Very smooth Si, smooth evaporated Au/Si, smooth evaporated-Al/Si, and rough sputtered-Al/Si were used as substrates. Their r.m.s. roughnesses, as measured by atomic force microscopy, were 1.27, 17.1, 21.1 and 65-118 Å, respectively. The crystalline structure and the angular spread of the (0 0* 2) plane normal to the ZnO films were determined using X-ray diffraction and X-ray rocking curves, respectively. The crystallinity and the preferred c-axis orientation of the ZnO films were strongly dependent on the surface roughness of the substrates rather than on the oxygen content of the working environment or on the chemical nature of the substrate.     

基于谐振原理的硅微机械加速度计

基于力学振动原理 ,导出敏感梁类谐振振动的微分方程 ,给出了振梁型加速度计的设计原理。指出了加速度计谐振梁频率的相对变化量与梁的厚度无关 ;为避免输出非线性频率信号 ,频率的相对变化率和激励振动的振幅都不宜太大     

A new method to suppress harmonics using /spl lambda//4 bias line combined by defected ground structure in power amplifiers

A new /spl lambda//4 bias line combined by a dumb-bell shaped defected ground structure (DGS) is proposed to suppress harmonics in power amplifiers. The proposed DGS bias line maintains the required high impedance even after DGS is inserted, while the width and length of the /spl lambda//4 bias line are broader and shorter than those of conventional bias lines. When the DGS bias line is used in power amplifiers, the third harmonic components as well as the second harmonic are reduced, because of the increased slow-wave effect over wide harmonic band. It is shown that the reduction of the third harmonic component, the improvement of 1 dB compression point, and power added efficiency are 26.5 dB, 0.45 dB, and 9.1%, respectively.     

向家坝水电站右岸隧道进出口边坡的处理研究

文章主要从实践方面介绍了向家坝水电站右岸地方还建公路北线段隧道洞口施工期边坡缺陷处理措施,并总结了几点经验,这对于以后公路隧道洞口的设计和施工,尤其是洞口边坡塌方的处理具有一定指导意义。     

Transmission performance of 10-Gb/s 1550-nm transmitters using semiconductor optical amplifiers as booster amplifiers

We have demonstrated the transmission performance of 10-Gb/s transmitters based on LiNbO/sub 3/ modulator using semiconductor optical amplifiers (SOAs) as booster amplifiers. Utilizing the negative chirp converted in SOAs and self-phase modulation induced by high optical power, we can successfully transmit 10-Gb/s optical signals over 80 km through the standard single-mode fiber with the transmitter using SOAs as booster amplifiers. SOAs can be used for booster amplifiers with a careful adjustment of the operating conditions. In order to further understand an SOA's characteristics as a booster amplifier, we model SOAs and other subsystems to verify the experimental results. Based on the good agreement between the experimental and simulation results, we can find the appropriate parameters of input signals for SOAs, such as extinction ratio, rising/falling time, and chirp parameter to maximize output dynamic range and available maximum output power (P/sub o,max/).     

合成丁苯嵌段共聚物的影响因素

采用负离子溶液聚合方法制备了丁苯嵌段共聚物，研究了引发剂、活化剂、偶合剂、终止剂对聚合产物性能的影响。     

Theoretical analysis of cladding-mode waveguide dispersion and its effects on the spectra of long-period fiber grating

A new method to control the free spectral range (FSR) of a long-period fiber grating (LPFG) is proposed and theoretically analyzed. As the refractive index decreases radially outward in the silica cladding by graded doping of fluorine, waveguide dispersion in the cladding modes was modified to result in the effective indexes change and subsequently the phase-matching conditions for coupling with the core mode in a LPFG. Enlargement of the FSR in a LPFG was theoretically confirmed.