Modeling of optical low coherence reflectometry recorded Braggreflectograms: evidence to a decisive role of Bragg spectral selectivity

This paper draws attention to the basic principles governing reflections in uniform Bragg reflectors (BR) when measured employing optical low coherence reflectometry (OLCR) technique. Using computations based on transfer matrix method (TMM), we first showed a strong spectral dependence of Bragg reflectograms on an OLCR probe spectrum. Later, this dependence is exploited to evaluate, for the first time, the coupling coefficient κ of a Bragg grating in a distributed Bragg reflector (DBR) laser on InP     

An active charge, passive discharge floor space heating system

This space heating system has a rockbed beneath and in contact with the floor of a dwelling, which is heated by radiation and convection from the floor. The ability of the heating system to maintain comfort conditions with no additional energy input is discussed and it is shown that the system is more suitable for use in mild climates than severe ones. Experimental work on horizontal air flow rockbeds is reported and shows that shallow beds can be designed in the same way as vertical air flow beds. The influence of natural convection on the effective thermal conductivity of the experimental rockbeds is reported.     

Ionoluminescence decay measured with single ions

A new ion beam analysis-based, single ion technique called the time to first photon has been developed to measure the decay of the luminescence signal of phosphors. Such measurements are currently needed to study luminescence decay mechanisms following high-density excitations and to identify strongly luminescent phosphor coatings with short lifetimes for ion photon emission microscopy (IPEM). The samples for this technique consist of thin phosphor layers placed or coated on the surface of PIN diodes. Single ions from an accelerator strike this sample and simultaneously create ion beam induced luminescence (IBIL) from the phosphor that is measured by a single-photon-detector, and an ion beam induced charge collection (IBICC) signal in the PIN diode. In this case, the IBICC signal provides the start pulse and the IBIL signal the stop pulse to a time to amplitude converter. It is straightforward to show that this approach also measures a signal proportional to activity versus time with an accuracy of 5% as long as the number of detected photons per ion is less than 0.1, which usually requires the use of absorbers for the IBIL detector or electronic discrimination for the IBIL signals. Details of the new analysis are given together with examples of luminescence decay measurements of several ceramic phosphors being considered to coat IPEM samples. IPEM is currently being developed at Sandia National Laboratory (SNL), the University of North Texas in Denton, and the Universities and INFN of Padova and Torino.     

In vivo validation of a thermodilution system designed to measure peripheral blood flow

A 5F triple-lumen thermodilution catheter was evaluated in a canine vena cava model to determine whether this catheter and the thermodilution technique provide valid in vivo determinations of blood flow. Our ultimate goal is to develop methods for studying limb blood flow in humans. Seven dogs were studied. Blood flow was provided and regulated by a calibrated roller pump. Flow rate determinations by thermodilution were made over a range of 0.5 to 5.01 1/minute. Excellent correlation (r = 0.98, r2 = 0.96, P less than 0.01) was found between actual flow and flow measured by thermodilution. The mean (+/- SD) coefficient of variation for the thermodilution method was 9.97 +/- 5.72 per cent over the flow range tested. The coefficient of variation tended to be higher at low flow rates. The thermodilution technique with this catheter provides valid in vivo determinations of blood flow through large vessels. This technology can be rationally applied to the study of limb blood flow in humans.     

The revised URGAP model to describe the gap conductance between fuel and cladding

The URGAP gap conductance model has been extended and revised generally. An enlarged data base consisting of approximately 1000 data has been constructed and was used to calibrate the revised URGAP model. With this model the gap conductance for very different conditions such as material pairing, gas and contact pressure, surface roughness of fuel and cladding, gap width, gas temperature and composition are very satisfactorily described. URGAP may be used in any code describing the fuel rod behaviour of any reactor type.     

Efficiency increase of an induction motor by improving coolingperformance

Improving the efficiency of induction motors, which are the most energy consuming electric machines in the world, saves much energy. The efficiency can be increased by improving cooling performance as well as by using better materials or by improving electromagnetic performance with better design. This paper presents the relationship between the efficiency or the losses and the temperature of coils with experiments as well as simulations by changing parameters such as the load and the flow rate of cooling air. The losses and the efficiency are calculated from an equivalent circuit method as well as experiments. Coil temperatures variation affects much on the efficiency. The internal cooling method is better than that of external cooling for the coil temperature reduction. Several cooling methods are compared focusing on the fan efficiency and performance, from which the values of the efficiencies of the motors are expected. The fan efficiency as well as the fan performance should be considered for the optimum fan design to increase the total efficiency of a motor. The simulations are validated by the comparison with the experiments     

A hybrid PC/PLC architecture for manufacturing-system control—theory and implementation

This paper presents a novel and generic PC/PLC-based software/hardware architecture for the control of flexible manufacturing workcells. The proposed implementation methodology is based on the utilization of any one of the available formal discrete-event-system control theories in conjunction with state-of-the-art industrial programmable-logic controllers (PLCs). The methodology has been illustrated to be a viable technique through its actual implementation in our laboratory using a robotic-workcell testbed. The specific control theory used is a combination of Extended Moore Automata and Ramadge-Wonham Automata that has been developed by our research group. The modular control software architecture has been developed for MS-Windows environments (running on one PC interfaced to the PLCs) and allows the use of different formal control theories as well as different commercial PLC hardware. The effective graphical user interface provides a transparent programming environment, where users are not expected to have a full knowledge of the formal control theory used.     

Analysis of the Safety of the Burial Grounds of Decontamination Waste of Chernobyl Origin in the Territory of Belarus

Unsatisfactory conditions of storage of decontamination waste (DW) in the storages formed in the territory of Belarus after the Chernobyl accident require the evaluation of the level of protection of the environment and population. The potential hazard of the decontamination waste burial grounds (DWBGs) has been evaluated based on the use of a generalized multichamber model that was verified by comparing the calculation results and the results obtained by the American (GW SCREEN) model. The characteristics of the 24 largest and most hazardous DWBGs are given and the evaluations of their safety are presented. The zones of influence of these storages, whose size varies from 100 to 330 m, have been determined. The reliability of the prediction evaluation of a possible hazardous radioactive contamination of water near the storages has been verified using the Dudichi DWBG as an example.     

New approach to modelling a flat plate collector: the Fourier transform technique

The efficiency of a flat plate collector is estimated. The transfer of heat energy through its absorber plate considered as its main part of structure is studied by solving the heat diffusion equation using the Fourier transform technique. The temperature of the working fluid is also obtained considering the heat balance equation and a simple suggested model for the considered collector. An expression useful for practical purposes to predict the hourly global solar irradiance on horizontal surface is given. It shows good fitting with corresponding experimental data recorded in Makkah, Jeddah and Hong Kong. The obtained formula is used in the theoretical analysis of the present heating problem. The trial is promising and shows that the dependence of the efficiency on the revealed factors is nonlinear.