Influence of SiC microstructure on its corrosion behavior in molten FLiNaK salt

The influence of the microstructure on the corrosion rate of three monolithic SiC samples in FLiNaK salt at 900 °C for 250 h was studied. The SiC samples, labeled as SiC-1, SiC-2, and SiC-3, had corrosion rates of 0.137, 0.020, and 0.043 mg/cm²h, respectively. Compared with grain size and the presence of special grain boundaries (i.e., Σ3), the content of high-angle grain boundaries (HAGBs) appeared to have the strongest influence on the corrosion rate of SiC in FLiNaK salt, since the corrosion rate increased six times as the concentration of high-angle grain boundaries increased from 19 to 32% for SiC-2 and SiC-1, respectively. These results stress the importance of controlling the content of HAGBs during the production process of SiC.     

Phase formation,structure and properties of light-weight aluminosilicate proppants based on clay-diabase and clay-granite binary mixes

One of the drawbacks of fusible clays is the narrow sintering interval due to a sharp increase in the amount of iron-silicate melt at a temperature of 1000–1100 °C, which hardens in the form of a glass phase upon cooling. This leads to a relatively low mechanical strength of the calcined samples and causes the danger of melting the granular material surface from such clays during the firing process. To increase the strength of samples of fusible clays, the influence of diabase and granitoid rocks was considered. It was found that the strengthening effect of diabase and granitoid rock additives in an amount of 20–50% in a mixture with fusible clay is due to an increase of total content of the crystalline phase (mullite, cristobalite and residual quartz) from 18–20% in clays without additives to 22–28 % - in mixtures with diabase and to 28–34% - with granitoid additives) at a temperature of 1050–1100 °C. This increase is due to the activation of synthesis processes of secondary mullite and crystallization from alkali-rich feldspar melt of amorphous silica, released from the structure of clay minerals. The established influence of the igneous rocks used made it possible to develop compositions and propose process flow sheet for producing aluminosilicate proppants based on fusible clays. The use of granitoid and diabase rocks in an amount of 20–70% with fusible clays produces lightweight aluminosilicate proppants with bulk density of 1.40–1.46 g/cm³ at temperature range of 1050–1100 °C, which can endure destructive pressures up to 34.5–52 MPa.     

Structural Basis for the Function of the C-Terminal Proton Release Pathway in the Calcium Pump

The calcium pump (sarco/endoplasmic reticulum Ca²⁺-ATPase, SERCA) plays a major role in calcium homeostasis in muscle cells by clearing cytosolic Ca²⁺ during muscle relaxation. Active Ca²⁺ transport by SERCA involves the structural transition from a low-Ca²⁺ affinity E2 state toward a high-Ca²⁺ affinity E1 state of the pump. This structural transition is accompanied by the countertransport of protons to stabilize the negative charge and maintain the structural integrity of the transport sites and partially compensate for the positive charges of the two Ca²⁺ ions passing through the membrane. X-ray crystallography studies have suggested that a hydrated pore located at the C-terminal domain of SERCA serves as a conduit for proton countertransport, but the existence and function of this pathway have not yet been fully characterized. We used atomistic simulations to demonstrate that in the protonated E2 state and the absence of initially bound water molecules, the C-terminal pore becomes hydrated in the nanosecond timescale. Hydration of the C-terminal pore is accompanied by the formation of water wires that connect the transport sites with the cytosol. Water wires are known as ubiquitous proton-transport devices in biological systems, thus supporting the notion that the C-terminal domain serves as a conduit for proton release. Additional simulations showed that the release of a single proton from the transport sites induces bending of transmembrane helix M5 and the interaction between residues Arg762 and Ser915. These structural changes create a physical barrier against full hydration of the pore and prevent the formation of hydrogen-bonded water wires once proton transport has occurred through this pore. Together, these findings support the notion that the C-terminal proton release pathway is a functional element of SERCA and also provide a mechanistic model for its operation in the catalytic cycle of the pump.     

Corrosion behavior of T24, T92, VM12, and AISI 304 steels exposed to KCl–NaCl–K2SO4–Na2SO4 salt mixtures

The corrosion mechanisms of T24, T92, VM12, and AISI 304 steels are studied under the influence of NaCl–KCl, NaCl–Na₂SO₄, and KCl–K₂SO₄ salt mixtures in a dry air atmosphere at 650°C for 15 days. NaCl–KCl was the most aggressive deposit and AISI 304 stainless steel exhibited the highest corrosion resistance. There was no relation between the Cr content of the ferritic steels and their corrosion resistance in NaCl–KCl. In contrast, the resistance of high-Cr steels was better when exposed to NaCl–Na₂SO₄ and KCl–K₂SO₄. The high-Cr and the low-Cr steels were more susceptible to NaCl–Na₂SO₄ and to KCl–K₂SO₄, respectively.     

An index structure supporting rule activation in pervasive applications

World Wide Web - Rule mechanism has been widely used in many areas, such as databases, artificial intelligent and pervasive computing. In a rule mechanism, rule activation decides which rules are...     

Uncertainties in the determination of pyrrolizidine alkaloid levels in naturally contaminated honeys and comparison of results obtained by different analytical approaches

The contamination of honey with hepatotoxic pyrrolizidine alkaloids (PAs) is a well-known hazard for food safety. While management strategies and controls of the honey industry aim to reduce the PA levels, uncertainties remain with regard to the safety of regionally produced and marketed honey. In addition, a previous study showed large differences of results obtained after various periods of storage and apparent differences between the analytical results of different laboratories. Therefore, this study aimed at examining these uncertainties by monitoring the impact of storage on the PA and PA N-oxide (PANO) content of two freshly harvested honeys and on possible demixing effects caused by pollen settling. Additionally, three analytical approaches – target analysis with matrix-matched calibration or standard addition and a sum parameter method – were applied for a comparative analysis of 20 honeys harvested in summer 2016. All samples originated from Schleswig-Holstein in Northern Germany where the PA plant Jacobaea vulgaris is currently observed on a massive scale. The results of the time series analyses showed that PANO levels markedly decreased within a few weeks and practically reached the LOD 16 weeks after harvest. Tertiary PAs, by contrast, remained stable and did not increase as a consequence of PANO decrease. The experiments on a putative demixing, which may result in a heterogeneous distribution of PAs/PANOs, revealed that there was no such effect during storage of up to 12 weeks. A comparison of the PA/PANO levels obtained by different analytical approaches showed that in some cases the sum parameter method yielded much higher levels than the target approaches, whereas in other cases, the target analysis with standard addition found higher levels than the other two methods. In summary, the results of this study highlight uncertainties regarding the validity and comparability of analytical results and consequently regarding health risk assessment.     

Effect of temperature on raw whole milk density and its potential impact on milk payment in the dairy industry

The objective of this study was to determine the effect of temperature on whole milk density measured at four different temperatures: 5, 10, 15, and 20 °C. A total of ninety-three individual milk samples were collected from morning milking of thirty-two Holstein Friesian dairy cows, of national average genetic merit, once every two weeks over a period of 4 weeks and were assessed by Fourier transform infrared spectroscopy for milk composition analysis. Density of the milk was evaluated using two different analytical methods: a portable density meter DMA35 and a standard desktop model DMA4500M (Anton Paar GmbH, UK). Milk density was analysed with a linear mixed model with the fixed effects of sampling period, temperature and analysis method; triple interaction of sampling period x analysis method x temperature; and the random effect of cow to account for repeated measures. The effect of temperature on milk density (ρ) was also evaluated including temperature (t) as covariate with linear and quadratic effects within each analytic method. The regression equation describing the curvature and density–temperature relationship for the DMA35 instrument was ρ = 1.0338−0.00017T−0.0000122T² (R² = 0.64), while it was ρ = 1.0334 + 0.000057T−0.00001T² (R² = 0.61) for DMA4500 instrument. The mean density determined with DMA4500 at 5 °C was 1.0334 g cm⁻³, with corresponding figures of 1.0330, 1.0320 and 1.0305 g cm⁻³ at 10, 15 and 20 °C, respectively. The milk density values obtained in this study at specific temperatures will help to address any bias in weight–volume calculations and thus may also improve the financial and operational control for the dairy processors in Ireland and internationally.     

Development of a new ion-imprinted polymer (IIP) with Cd2+ ions based on divinylbenzene copolymers containing amidoxime groups

Polymer Bulletin - In this study, we synthesized a new ion-imprinted polymer (IIP) based on introduction of amidoxime groups in acrylonitrile, complexation with Cd2+ ions and polymerization with...