Tape casting of polysiloxane-derived ceramic with controlled porosity and surface properties

Tape casting has been applied to produce porous hybrid and SiOC ceramic tapes using ceramic precursors and commercially available polysiloxanes as polymeric binders. SiC particles of two different mean sizes (4.5 or 6.5?μm) were used as inert fillers to prevent shrinkage and increase mechanical stability. Macroporosity was adjusted by varying the azodicarbonamide (ADA) content from 0 to 30?wt.%. Decomposition of the polysiloxanes at 600?°C resulted in the generation of micropores with high specific surface area (187–267 m²?g^?1) and a predominant hydrophobic behavior. At 1000?°C mainly meso/macroporosity were observed (SSA: 32–162 m²?g^?1) accompanied by increased hydrophilicity. The influence of ADA content, SiC size, and pyrolysis temperature on open porosity (2.5–37%), average pore size (<0.01–1.76?μm), surface characteristics, and flexural strength (10.5–121?MPa) were investigated. The porous tapes with different surface characteristics and controlled structure are highly promising for applications involving membrane processes, particularly microfiltration systems (0.1–10?μm).     

EFFECT OF HEATING MODES ON INTERNAL STRAIN-STRESS FORMATION DURING DRYING OF MOLDED CERAMICS

Parametric analyses in drying processes of molded ceramics are performed to investigate the influence of heating modes on the formation of drying-induced strain-stress as well as the drying characteristic. The transient three-dimensional problem of strain-stress and heat and moisture transfer in a slab is solved simultaneously by the finite element method. Three modes of hot air, intermittent and internal heating are compared by modeling in the normalized parameters. The tensile and compressive stresses fluctuate, and fall remarkably during the low Biot number period when the slab is heated intermittently. In the internal heating mode, the drying rate is the fastest but stress formation is maintained at the lowest level among the three modes. This effectiveness of the internal heating is investigated experimentally by employing the microwave heating as well.     

STD‐NMR‐Based Protein Engineering of the Unique Arylpropionate‐Racemase AMDase G74C

Structure‐guided protein engineering achieved a variant of the unique racemase AMDase G74C, with 40‐fold increased activity in the racemisation of several arylaliphatic carboxylic acids. Substrate binding during catalysis was investigated by saturation‐transfer‐difference NMR (STD‐NMR) spectroscopy. All atoms of the substrate showed interactions with the enzyme. STD‐NMR measurements revealed distinct nuclear Overhauser effects in experiments with and without molecular conversion. The spectroscopic analysis led to the identification of several amino acid residues whose substitutions increased the activity of G74C. Single amino acid exchanges increased the activity moderately; structure‐guided saturation mutagenesis yielded a quadruple mutant with a 40 times higher reaction rate. This study presents STD‐NMR as versatile tool for the analysis of enzyme–substrate interactions in catalytically competent systems and for the guidance of protein engineering.     

Emission of Particulate Matter 2.5 (PM2.5) from Sewage Sludge Incinerators in Japan

Because fine particulate matter ≤2.5 µm in diameter (PM2.5) causes health problems, PM2.5 emissions are of concern. However, little research on stationary sources has been conducted. To determine the concentration and filtration behavior of PM2.5, dust was collected from five fluid-bed sewage sludge incinerators (SSIs) sorted by particle size using cascade impactors. The average PM2.5 concentration was 0.00014–4.8 mg/Nm³. The total estimated amount of PM2.5 emissions from the SSIs for all plants in Japan was 0.96–8.9 tons/year. Since the SSIs with dry Electrostatic Precipitators (EP) contributed 75–99% of the total emissions, replacing dry EPs with bag filters would significantly reduce the PM2.5 emissions from SSI.     

Effect of a low-fat diet enriched with oleic acid on postprandial lipemia in patients with type 2 diabetes mellitus

The aim of the present study was to compare the effects of a low-fat diet enriched with oleic acid to those of a low-fat diet enriched with linoleic acid on fasting lipids, postprandial lipemia, and oxidative susceptibility of low-density lipoprotein (LDL) in patients with type 2 diabetes mellitus (DM). In a 3-wk randomized crossover study, eight patients with type 2 DM were given an experimental low-fat diet enriched with either oleic acid or linoleic acid. The oleic-acid-enriched diet contained 5, 15, and 5% energy from saturated, monounsaturated, and polyunsaturated fatty acids, and the linoleic-acid-enriched diet contained 5, 5, and 15% energy from saturated, monounsaturated, and polyunsaturated fatty acids, respectively. In addition to evaluating the fasting lipids and oxidative susceptibility of LDL, we evaluated postprandial lipemia using an oral fat load at the end of each 3-wk dietary phase. There were no significant differences in fasting lipid profile or lag time of LDL oxidation between the two experimental dietary phases. The average and maximal increments of remnant-like particle (RLP) cholesterol levels during oral fat load were significantly higher after the oleic-acid-enriched dietary phase than after the linoleic-acid-enriched dietary phase. The area under the curve of RLP cholesterol was also significantly larger after the oleicacid-enriched dietary phase than after the linoleic-acid-enriched dietary phase. These results suggest that the oleic-acidenriched diet was associated with increased formation of postprandial chylomicron remnants compared with the linoleicacid-enriched diet.     

Effect of the Magnetostrictive Layer on Magnetoelectric Properties in Lead Zirconate Titanate/Terfenol-D Laminate Composites

Magnetoelectric laminate composites of piezoelectric/magnetostrictive materials were prepared by stacking and bonding together a PZT disk and two layers of Terfenol-D disks with different directions of magnetostriction. These composites were studied to investigate (i) dependence on the magnetostriction direction of the Terfenol-D disk and (ii) dependence on the direction of the applied ac magnetic field. Three different types of assemblies were prepared by using two types of disks: one with magnetostriction along the radial direction, the other with magnetostriction along the thickness direction. The maximum magnetoelectric voltage coefficient (d E /d H ) of 5.90 V/cm·Oe was obtained for a design where the composite was made by two Terfenol-D layers with a radial magnetostriction direction.     

Effect of Additives on the Electromechanical Properties of Pb(Zr,Ti)O3–Pb(Y2/3W1/3)O3 Ceramics

Dielectric and piezoelectric properties of 0.02Pb(Y_2/3W_1/3)O₃ 0.98Pb(Zr0.52Ti0.48)O3 ceramics doped with additives (Nb₂O₅, La₂O₃, MnO₂, and Fe₂O₃) were investigated. The grain sizes of these ceramics decreased with increasing amounts of additives. For additions of MnO₂ and Fe₂O₃, dielectric losses decreased, while for Nb₂O₅ and La₂O₃, these values increased. The maximum values of the mechanical quality factor Q_m were found to be 956 and 975 for additions of 0.9 wt% Fe₂O₃ and 0.7 wt% MnO₂, respectively, but donor dopants (Nb₂O₅ and La₂O₃) did not change the values of Q_m . On the other hand, the piezoelectric constant d₃₃ and the electromechanical coupling factor k_p decreased with additions of MnO₂ and Fe₂O₃, but improved with additions of Nb₂O₅ and La₂O₃.     

Fabrication and Mechanical Properties of Continuously Graded MoSi2–ZrO2(2Y) Materials Using Wet-Molding

Continuously graded MoSi₂-ZrO₂(2Y) materials with high density (97.5% of theoretical) have been fabricated by uniaxial wet-molding, followed by hot pressing (1000°C/1 h/30 MPa) and hot isostatic pressing (1400°C/2 h/196 MPa). Their composition profiles are greatly influenced by the viscosity of mixed solutions of glycerin and ethanol used as a dispersion medium; a linear compositional gradient from MoSi₂/ZrO₂(2Y) 70/30 to 20/80 mol% is obtained from the solution (50/50 vol%) with a viscosity of 20 mPa s. Vickers hardness (Hv) and fracture toughness (KIC) increase from 9.7 to 12.4 GPa and from 5.1 to 12.5 MPa m1/2, respectively, with increasing ZrO₂(2Y) composition.     

Incorporation of benzothiadiazole moiety at junction of polyfluorene–polytriarylamime block copolymer for effective color tuning in organic light emitting diode

Block copolymer consisting of polyfluorene and polytriarylamine with benzothiadiazole moiety at the junction is prepared in order to obtain an orange emitting polymer via Suzuki‐Miyaura followed by Buchwald‐Hartwig coupling reactions. Electroluminescent device fabricated with resulting block copolymer exhibit only orange emission, although slight blue emission is observed in the fluorescent spectrum for the thin film, indicating that benzothiadiazole part plays a role of an effective trap site. Devices based on polyfluorene homopolymer doped with block copolymer (10 wt %) or an orange emitting model compound at the corresponding content of benzotiadiazole unit are also fabricated. The device with the model compound exhibits orange emission with Commission Internationale de l'Éclairage (CIE) coordinate of (0.58, 0.42), whereas that with block copolymer pale orange with the coordinate of (0.44, 0.38). This fact is probably due to the preferential distribution of block copolymer at the vicinity of anode via hydrophilic interaction of trioxyethylene side chains with poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate). © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45393.     

Characterization of piezoelectric ceramics using the burst/transient method with resonance and antiresonance analysis

In this paper, a comprehensive methodology for characterizing the high power resonance behavior of bulk piezoelectric ceramics using the burst method is described. In the burst method, the sample is electrically driven at its resonance frequency, and then either a short circuit or an open circuit condition is imposed, after which the vibration decays at the resonance or antiresonance frequency, respectively. This decay can be used to measure the quality factor in either of these conditions. The resulting current in the short circuit vibration condition is related to the vibration velocity through the “force factor.” The generated voltage in the open circuit vibration condition corresponds to the displacement by the “voltage factor.” The force factor and the voltage factor are related to material properties and physical dimensions of the sample. Using this method, the high power behavior of the permittivity, compliance, effective piezoelectric charge constant, electromechanical coupling factor, and material losses can be determined directly by measuring the resonance (short circuit) and antiresonance (open circuit) frequencies, their corresponding quality factors, the force factor A, and the voltage factor B. The experimental procedure to apply this method is described and demonstrated on commercially available hard and semi‐hard PZT materials of geometry.