Preparation of Aluminum Nitride–Silicon Carbide Nanocomposite Powder by the Nitridation of Aluminum Silicon Carbide

Aluminum nitride (AlN)–silicon carbide (SiC) nanocomposite powders were prepared by the nitridation of aluminum-silicon carbide (Al₄SiC₄) with the specific surface area of 15.5 m²·g⁻¹. The powders nitrided at and above 1400°C for 3 h contained the 2H-phases which consisted of AlN-rich and SiC-rich phases. The formation of homogeneous solid solution proceeded with increasing nitridation temperature from 1400° up to 1500°C. The specific surface area of the AlN–SiC powder nitrided at 1500°C for 3 h was 19.5 m²·g⁻¹, whereas the primary particle size (assuming spherical particles) was estimated to be ∼100 nm.     

Enantioselective addition Of diketene to aldehydes promoted by chiral schiff base—titanium alkoxide complex. Application to asymmetric synthesis of potential inhibitors of HMG coenzyme reductase

Highly enantioselective addition of diketene to aldehydes was achieved by using novel Schiff base—titanium alkoxide complexes. Up to 92% ee of 5-hydroxy-3-oxoesters was obtained. This procedure provides an efficient method for the asymmetric synthesis of potential inhibitors of HMG coenzyme reductase.     

Capillary rise properties of porous mullite ceramics prepared by an extrusion method with various diameters of fiber pore formers

Porous mullite ceramics with unidirectionally oriented pores were prepared by an extrusion method using rayon fibers as the pore formers. Rayon fibers of 8.1, 9.6, 16.8, and 37.6 μm in diameter were used as the pore formers and were kneaded with alumina powder, kaolin clay, China earthen clay, and water to form pastes. These pastes were extruded into cylindrical tubes, dried, and fired at 1500 °C for 4 h. The apparent porosities ranged from 45.7 to 48.2 %. The pore size distributions showed a sharp peak at 9.4, 10.0, 15.6, and 30 μm with increasing fiber diameters. The height of the capillary rise was 1780, 1670, 1320, and 950 mm with increasing fiber diameter. The maximum capillary rise is much higher than previously reported. The contact angle and effective pore radius that determine the capillary rise ability were calculated by fitting the capillary rise curves using the Fries and Dreyer’s equation.     

Super‐reflective color LCD with PDLC technology

Abstract— A novel reflective color LCD without polarizers has been developed using a PDLC film and a retro‐reflector. Bright color images including moving images are achievable with ambient light. This novel LCD will enable the new application area of electronic paper.     

Starting method of a superconducting generator in a combined‐cycle power plant

In the combined‐cycle power plant generators are started by using the igniting arrangement up to the ignition rotational speed of the gas turbine. On the other hand, in the case of using the superconducting generator, it is difficult to apply the igniting arrangement used to generate electricity on the combined cycle for the structure as is. We examined the induction motor starting method for the superconducting generator by using the 70‐MW‐class quick‐response excitation superconducting model generator and the VVVF power supply. From the examination, we confirmed the ability to raise the rotational speed from 6 to 360 rpm. Moreover, it was found to be able to start 200‐MW‐class superconducting generators by the induction motor starting method with the analysis. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 160(2): 30– 38, 2007; Published online in Wiley InterScience ( www.interscience. wiley.com ). DOI 10.1002/eej.20283     

Study on sustainable redevelopment of a densely built-up area in Tokyo by introducing a distributed local energy supply system

“Distributed local energy systems” had been expected to rationalize the supply of energy to built-up areas, but until now very little research has been performed to estimate the effect of their application to actual cities. In this research, therefore, a future vision for the year 2030 in the Sancha Area (SANCHA VISION 2030), a typical densely built-up area in Tokyo, has been elaborated including a simulation to estimate benefits from the application of distributed energy systems in terms of reduced energy consumption and CO₂ emissions as well as mitigation of the heat-island phenomenon. As a result, it was demonstrated that a “distributed local energy system”, which provides a district with both electrical power and heat through an integrated distribution system, may contribute to a considerable improvement in energy efficiency for those areas. In addition, it may also provide other benefits, including enhancement of living amenity and urban security in times of emergency.     

The fabrication and thermomechanical behavior of Al and Ti SMA composites

Two kinds of composites—Ti-Ni shape-memory alloy (SMA) fiber-reinforced 6061 aluminum matrix composite and Ti-Pd(Ni) SMA-reinforced titanium-matrix composite—were fabricated by various processing methods and their microstructure and thermomechanical behavior were investigated. In both sets of composites, an increase in yield stress at high temperature was mainly caused by residual compressive stress created in the matrix in association with shape-memory effects of the embedded SMAs. For more information, contact Kiyoshi Mizuuchi, Osaka Municipal Technical Research Institute, Osaka 536-8553, Japan; e-mail: mizuuchi@omtri.city.osaka.jp.     

Sinterability of various high-purity magnesium oxide powders

The sinterability of high-purity MgO powders with different production histories was investigated to make clear the relationship between the powder characterization, the densification processes, and the changes in microstructure both with increasing temperature at a rate of 10° C min^–1 and at a fixed temperature of 1450° C for 5 h. The densification behaviour and the changes in microstructure of these compressed bodies were affected chiefly by their original surface activity and degree of agglomeration, depending on the production histories: (i) the ultra-fine and well-dispersed powder prepared by the vapour-phase oxidation process showed that densification proceeded with an appreciable grain growth with few closed pores remaining; (ii) powder derived from the sea-water magnesia process showed that the densification behaviour was affected by the species of magnesium salt, i.e. basic magnesium carbonate or magnesium hydroxide, used as a precursor; however, whichever magnesium salt was used, its sintered compact showed similar closed porosities and grain-size distributions; (iii) powder derived from the spark-discharge process contained skeletons of the original Mg(OH)₂ particles; however, the densification proceeded gradually with slow grain growth, reflecting the fact that the powder has a moderate surface area (36 m² g^–1). The sintered compact from (iii) had a small closed porosity and the smallest grain-size distribution among the compacts used in this investigation.     

A New Silicon Sensor for Hot Metal Measurements

In the present study, an electrochemical sensor has been designed for the direct measurement of silicon content in hot metal. The sensor represents a galvanic silicon concentration cell of the type Ni_sat—Si(1) II silicate electrolyte (1) II Fe—C—Si(1) The tubular silica-glass sensor can be immediately immersed into the metal bath at a response time of 30 to 60 s. A reproducible EMF vs. wt.% Si relationship was obtained for measurements in carbon-saturated Fe—C—Si melts at 1400°C and Si contents from 0.05 to 1.8 wt.%. This relationship is nearly identical with the cell function calculated from thermodynamic data.