Hydrogen bonding,miscibility, crystallization,and thermal stability in blends of biodegradable polyhydroxyalkanoates and polar small molecules of 4‐tert‐butylphenol

The hydrogen bonding, miscibility, crystallization, and thermal stability of poly(3‐hydroxybutyrate) (PHB)/4‐tert‐butylphenol (BOH) blends and poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) [P(3HB‐3HHx)]/BOH blends were investigated by Fourier transform infrared (FTIR) spectroscopy, solid‐state¹³C‐NMR, differential scanning calorimetry, wide‐angle X‐ray diffraction (WAXD), and thermogravimetric analysis. The results of FTIR spectroscopy and solid‐state¹³C‐NMR show that intermolecular hydrogen bonds existed between the two components in the blends and that the interaction was caused by the carbonyl groups in the amorphous phase of both polyesters and the hydroxyl groups of BOH. With increasing BOH content, the chain mobility of both the PHB and P(3HB‐3HHx) components was improved. After the samples were quenched, the detected single glass‐transition temperatures decreased with composition, indicating that both PHB/BOH and P(3HB‐3HHx)/BOH were miscible blends in the melt. Moreover, as BOH content increased, the melting temperatures of PHB and P(3HB‐3HHx) clearly decreased, which implied that their crystallization was suppressed by the addition of BOH. Although the crystallinity of PHB and P(3HB‐3HHx) components decreased with increasing BOH content in the blends, their crystal structures were hardly affected after they were blended with BOH, which was further proven by WAXD results. In addition, the thermal stability of PHB was improved by a smaller amount of BOH.     

A study of cell nucleation in the extrusion of polypropylene foams

An investigation has been performed of the cell nucleation and initial growth behaviors in the foam processing of polypropylene (PP) in both the linear and branched forms. These materials were foamed in extrusion with the two blowing agents, CO₂ and isopentane. The cell density generally increased with an increased content of the blowing agent, for both CO₂ and isopentane. The effect of processing pressure on the cell density was distinct when CO₂ was used, whereas no pressure effect was observed in the foam processing with isopentane. The cell morphologies for the two PPs were found to be significantly different. A slightly lower nuclei density was observed in the branched PP foams than in the linear PP foams. However, the phenomenon of cell coalescence was observed much less in the branched PP foams. Most cells in the branched PP foams were closed, whereas in the linear PP foams they were connected to each other. The experimental results indicated that the branched structure played an important role in determining the cell morphologies through its effects on the melt strength and/or melt elasticity.     

TESTS FOR FRACTIONAL INTEGRATION:A MONTE CARLO INVESTIGATION

Abstract. The performance of the Geweke-Porter-Hudak (GPH) test, the modified rescaled range (MRR) test and two Lagrange multiplier (LM) type tests for fractional integration in small samples is examined using Monte Carlo methods. Both the GPH and MRR tests are found to be robust to moderate autoregressive moving-average components, autoregressive conditional heteroskedasticity effects and shifts in the variance. However, these two tests are sensitive to large autoregressive moving-average components and shifts in the mean. It is also found that the LM tests are sensitive to deviations from the null hypothesis. As an illustration, the GPH test is applied to two economic data series.     

Polysulphone and poly(phenylene sulphide) blends: 1. Thermal characterization and phase morphology

The phase behaviour and morphology of injection moulded specimens of polysulphone (PSF) and poly(phenylene sulphide) (PPS) blends were studied by differential scanning calorimetry (d.s.c.), dynamical mechanical thermal analysis (d.m.t.a.) and transmission electron microscopy (TEM). The blends are phase separated regardless of the blend composition as revealed by d.s.c., d.m.t.a. and TEM. Upon annealing at 160°C for 2 h, d.m.t.a. results indicate that the PPS phase remains in the amorphous state at compositions <10%. At compositions between 20 and 35%, the PPS appears to be dispersed in a mixed mode of amorphous and crystalline domains. Above 35% the PPS phase appears to become fully crystallized upon annealing of the blends. At 10% PPS, TEM results showed 35–200 nm size dispersion both in the as-moulded and in the annealed specimens. At 20% the PPS phase varied widely in size, from 35 nm to tens of micrometres but remained as an included phase. TEM also revealed a compound morphology of the included phase at a composition of 50 wt% of each component.     

Fundamental Optical Absorption Edge of Sputter-Deposited Zirconia and Yttria

Zirconia and yttria films were sputter deposited onto unheated fused silica substrates using a metal target and rare gas-oxygen discharges. Double-beam spectrophotometry was used to measure the transmission and reflection as a function of incident photon energy, E , from which the absorption coefficient, α( E ), was calculated. An indirect interband transition at E _i= 4.70 eV and two direct interband transitions at E _g1= 5.17 eV and E _g2= 5.93 eV occur in monoclinic zirconia. Two direct interband transitions at E _g1= 5.07 eV and E _g2= 5.73 eV occur in cubic yttria. The absorption edge structure is modified when unusual phases, such as tetragonal zirconia, and zirconia and yttria with no longrange crystallographic order, are present.     

The kinetics of polyarylate hydrolytic embrittlement

The hydrolysis of polyarylate in water between 55 and 98°C was found to be a zero-order process with an activation energy of 19.2 kcal/mol, determined by changes in molecular weight. The equation for the effect of temperature on the rate of hydrolysis is ln k = 34.1 ? 10⁴/T, where k is in day^?1. The decrease in molecular weight is accompanied by a loss in ductility. The transition from a ductile to brittle failure in tension occurs at M?_w of about 35,000 and M?_n of 12,700. At 27°C (80°F) and high humidity environment this would occur after 21 years. But during injection molding, the material, if not properly dried, would embrittle in a matter of seconds.     

Preparation and cell-materials interactions of plasma sprayed strontium-containing hydroxyapatite coating

The use of strontium-containing hydroxyapatite (Sr-HA) as a biomaterial has been reported recently. In vitro and in vivo studies have shown that Sr-HA promotes osteoblast response and stimulates new bone formation. In order to extend its usage to major load-bearing applications, such as artificial hip replacement, it has been proposed that the material could be used in the form of a coating on implant surfaces. This paper reports a preliminary study of biocompatibility of plasma sprayed Sr-HA coatings on a metallic substrate. Coatings of Sr-HA containing 10 mol% Sr²⁺ was produced on titanium alloy substrates. The coating exhibited good bonding with the substrate. The bioactivity of Sr-HA coating was evaluated in vitro by immersion in simulated body fluid (SBF). After immersion in SBF, Sr-HA coating exhibited great ability to induce apatite precipitation on its surface. The possible effects of cell-materials interactions of Sr-HA coating were examined by culturing osteoprecursor cells (OPC1) on coating surfaces. The effect of Sr-HA was also compared to a hydroxyapatite (HA) coating, which is widely used in orthopedics and dentistry. The results indicated that Sr-HA coating had good biocompatibility with human osteoblasts. OPC1 cells survived and proliferated well on the surface of coating. Sr-HA coating promoted OPC1 cells attachment, and more local contacts were produced on the surface. The presence of Sr stimulated OPC1 cell differentiation and ALP expression. No deleterious effect on ECM formation and mineralization was found with Sr-HA coating. The results indicated that Sr-HA coating had good mechanical properties and bioactivity in vitro.     

Aggregate‐induced emission in light‐emitting liquid crystal display technology

Nowadays, liquid crystal displays (LCDs) with light‐emission are considered as energy‐efficient devices and are promising alternatives to conventional LCDs. To realize such possibility, strong fluorescent materials with a dichroic properties are required. Aggregate‐induced emission (AIE) is an unusual photophysical phenomenon shown by some luminogenic materials that will be highly emissive in their aggregate state. In this work, we studied the AIE effect of a luminescent liquid crystalline molecule TPE‐PPE in our LC system as a luminophore dopant. The result showed the excellent AIE effect that higher concentration of luminogen in the nematic LC host induced stronger luminescent intensity. Through exposure of a photoisomeriable alignment material sulfonic‐dye‐1, the photopatterning of a light‐emitting LC device was achieved with the use of the TPE‐PPE/nematic LC mixture.     

Ferroelectric liquid crystals: Excellent tool for modern displays and photonics

The ferroelectric liquid crystals, because of their fast electro‐optical response, are one of the most important classes of liquid crystals. Here, in this review, we have summarized the different electro‐optical modes for ferroelectric liquid crystals. Clark–Lagerwall effect (surface stabilized ferroelectric liquid crystal), deformed helix ferroelectric (DHF) effect, electrically suppressed helix (ESH) mode, DHF orientational Kerr effect, and ESH diffraction modes have been discussed. All of the crucial features, that is, optics, electro‐optics, dynamics, and their dependence on material parameters, operational regime, and applications, have been reviewed.