Optimization of a photopolymerizable holographic recording material based on polyvinylalcohol using angular responses

Acrylamide-based holographic recording materials have significant advantages and the composition of these materials has been optimized in terms of energetic sensitivity and diffraction efficiency. As a result, diffraction gratings with an efficiency of almost 80% for energetic exposures of 35 mJ/cm² and a spatial frequency of 1000 lines/mm in photosensitive films 65 μm thick have been obtained. In this paper we present the effects of intensity, thickness, and variation in the concentration of each component by studying the angular responses of the diffraction gratings recorded in each composition.     

1.6 Tbit/s (40/spl times/40 Gbit/s) DPSK transmission over 3/spl times/100 km of TeraLight fibre with direct detection

By transmitting 40 channels over 300 km of TeraLight fibre, it is shown that optical differential phase shift keying can be used in 100 GHz-spaced 40 Gbit/s systems, with direct detection and a simple receiving filter. Chromatic dispersion tolerance around 300 ps/nm is also measured, compared to 70 ps/nm for NRZ.     

Programmable group-delay module using binary polarization switching

We demonstrate the first programmable group-delay module based on polarization switching. With a unique binary tuning mechanism, the device can generate any differential group delay value from -45 to +45 ps with a resolution of 1.40 ps, or any true-time-delay value from 0 to 45 ps with a resolution of 0.7 ps. The delay varying speeds for both applications are under 1 ms and can be as fast as 0.1 ms. We evaluate both the dynamic and static performances of the device while paying special attention to its dynamic figures of merit for polarization-mode dispersion emulation and compensation applications. Our experiment shows that the device exhibits a negligible transient-effect induced power penalty (<0.2 dB) in a 10-Gb/s nonreturn-to-zero system.     

Positively Thermo‐Sensitive Monodisperse Core–Shell Microspheres

In this paper, we report on a novel family of monodisperse thermo‐sensitive core–shell hydrogel microspheres that is featured with high monodispersity and positively thermo‐responsive volume phase transition characteristics with tunable swelling kinetics, i.e., the particle swelling is induced by an increase rather than a decrease in temperature. The microspheres were fabricated in a three‐step process. In the first step, monodisperse poly(acrylamide‐co‐styrene) seeds were prepared by emulsifier‐free emulsion polymerization. In the second step, poly(acrylamide) or poly[acrylamide‐co‐(butyl methacrylate)] shells were fabricated on the microsphere seeds by free radical polymerization. In the third step, the core–shell microspheres with poly‐ (acrylamide)/poly(acrylic acid) based interpenetrating polymer network (IPN) shells were finished by a method of sequential IPN synthesis. The proposed monodisperse core–shell microspheres provide a new mode of the phase transition behavior for thermo‐sensitive “smart” or “intelligent” monodisperse micro‐actuators that is highly attractive for targeting drug delivery systems, chemical separations, sensors, and so on.     

Formation of C49-TiSi2 in flash memories: a nucleation controlled phenomenon?

The formation of Ti silicides has been examined in flash memories with 0.25 μm linewidth by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. It has been observed that, after the first rapid thermal process and the selective metal etch, there is no silicide on the source and on a majority of drain contacts while C49-TiSi₂ is found on the gate. A pre-amorphisation implant increases drastically the formation of C49-TiSi₂ in the drain zone while modifications of annealing conditions have little impact. These results indicate that the formation of C49-TiSi₂ is most likely controlled by nucleation and that this nucleation is sensitive to both the width and the length of the reaction zone. The formation of a Ti rich silicide may play an important role in this nucleation by decreasing the driving force for the formation of C49-TiSi₂. Curiously enough, the formation of C49-TiSi₂ appears thus as a major concern for the salicide process in flash memories.     

High‐Performance,Monolithic Polyaniline Electrochemical Actuators

New polyaniline (PANI) asymmetric membranes were fabricated using a phase‐inversion technique with hexane as the coagulation bath. These membranes exhibit a dense structure with macrovoids distributed asymmetrically throughout the cross‐section. A stress–strain study demonstrated that the Young's modulus (1.421 GPa) and strain at break (7.6 %) of the new PANI asymmetric membranes prepared from hexane are approximately 12 and 4 times higher, respectively, than the values reported previously for the PANI integrally skinned asymmetric membranes (ISAMs) (123 MPa Young's modulus and 1.8 % strain at break). Furthermore, monolithic electrochemical actuators based on a single PANI asymmetric membrane were constructed, and a bending movement of up to 20 Hz was experimentally recorded in a hydrochloric acid aqueous solution. A lifetime of over 329 500 cycles was determined for these actuators at a ± 2° angular displacement (5 Hz). The lifetime is limited by a bending fatigue that creates a transversal crack on the PANI membrane at the air–water interface. Control over the actuator movement is also manifested by the linear dependences of the bending angle on the charge and of the angular velocity on the current. These relationships are independent of both the kind of applied electric signal and the frequency used.     

Origin of the threshold voltage instability in SiO/sub 2//HfO/sub 2/ dual layer gate dielectrics

The magnitude of the V/sub T/ instability in conventional MOSFETs and MOS capacitors with SiO/sub 2//HfO/sub 2/ dual-layer gate dielectrics is shown to depend strongly on the details of the measurement sequence used. By applying time-resolved measurements (capacitance-time traces and charge-pumping measurements), it is demonstrated that this behavior is caused by the fast charging and discharging of preexisting defects near the SiO/sub 2//HfO/sub 2/ interface and in the bulk of the HfO/sub 2/ layer. Based on these results, a simple defect model is proposed that can explain the complex behavior of the V/sub T/ instability in terms of structural defects as follows. 1) A defect band in the HfO/sub 2/ layer is located in energy above the Si conduction band edge. 2) The defect band shifts rapidly in energy with respect to the Fermi level in the Si substrate as the gate bias is varied. 3) The rapid energy shifts allows for efficient charging and discharging of the defects near the SiO/sub 2//HfO/sub 2/ interface by tunneling.     

Power combining characteristics of backed-off traveling wave tubes for communications applications

Traveling wave tubes (TWTs) used in multi-tone and digital communications applications are typically operated backed off from saturation in order to improve the amplifier linearity. This reduces the bit error rate (BER), decreases intermodulation distortion and lowers adjacent channel power; all at the expense of reducing the average output power. For emerging telecommunications applications, the average power requirement is increasing to provide higher bit rates and lower BER, and often exceeds the power obtainable from backed-off space or telecommunications TWTs. One solution is to power combine TWTs that are operated 3 to 10 dB backed off from saturation. Efficient power combining requires that the phase and gain of the signal from each TWT be closely matched. To understand the variation in these parameters across a build-set of tubes, the phase and gain versus drive of 35 Boeing S-band 5525H TWTs were measured. The standard deviation in the phase about the mean phase shift measured at saturation was found to be 2.6/spl deg/, with a related standard deviation of the gain compression at saturation of 0.22 dB. These levels result in small power combining losses and small errors in phased-array fed multi-beam antennas in broadband multi-tone applications.     

Thermal aging of plasticized PVC. I. Weight loss kinetics in the PVC—didecylphtalate system

Weight-loss kinetics were studied for 10 industrial extruded samples of poly(vinyl chloride) (PVC) plasticized by 20–30% by weight of didecylphtalate at 85, 95, 105, 110, and 120deg;C. For the most unstable samples, which contained a light coplasticizer, the weight-loss rate obeyed Fick's law. In the other cases, it was constant in the early period of exposure. The apparent Arrhenius parameters (i.e., preexponential factor and activation energy) were intercorrelated and varied strongly from one sample to another. This was explained by the existence of two distinct kinetic regimes corresponding, respectively, to diffusion or evaporation, the whole process being controlled by the slowest step, and a transition between both regimes occurring in the temperature range of exposure. In the proposed model, small changes of the preexponential factor of diffusion from one sample to another are sufficient to take into account the observed behavior.