Evanescently coupled photodiodes integrating a double-stage taper for 40-Gb/s applications-compared performance with side-illuminated photodiodes

The design, fabrication, and performance of double-stage taper photodiodes (DSTPs) are reported. The objective of this work is to develop devices compatible with 40-Gb/s applications. Such devices require high efficiency, ultrawide band, high optical power handling capability, and compatibility with low-cost module fabrication. The integration of mode size converters improves both the coupling efficiency and the responsivity with a large fiber mode diameter. Responsivity of 0.6 A/W and 0.45 A/W are achieved with a 6-/spl mu/m fiber mode diameter and cleaved fiber, respectively, providing relaxed alignment tolerances (/spl plusmn/1.6 /spl mu/m and /spl plusmn/2 /spl mu/m, respectively), compatible with cost-effective packaging techniques. DSTPs also offer a wide bandwidth greater than 40 GHz and transverse-electric/transverse-magnetic polarization dependence lower than 0.2 dB. Furthermore, a DSTP saturation current as high as 11 mA results in optical power handling greater than +10 dBm and a high output voltage of 0.8 V. These capabilities allow the photodiode to drive the decision circuit without the need of a broad-band electrical amplifier. The DSTP devices presented here demonstrate higher responsivities with large fiber mode diameter and better optical power handling capabilities and are compared with classical side-illuminated photodiodes.     

Adaptive antenna system design for multi-element combining with transient interrupted channels

This paper presents an analysis and design procedure for a buoyant cable array antenna used for satellite communications. The towed multi-element array is susceptible to washovers and fluctuations due to the ocean wave interaction with the floating hose where the elements are housed. A model of system performance for coherent multi-element combining is presented based on the dropouts and fades of the individual elements. The array design, including the number and spacing of elements, is shown to be highly dependent on the individual element exposure characteristics and the degree of correlation of the fades between channels. The joint statistics of the array are analyzed using a binary conditional element exposure model and a first-order Markov interelement correlation model. Using this analysis, a family of array designs meeting the communications requirements is produced.     

A 1-V 10.7-MHz switched-opamp bandpass /spl Sigma//spl Delta/ modulator using double-sampling finite-gain-compensation technique

A 1 V switched-capacitor (SC) bandpass sigma-delta (/spl Sigma//spl Delta/) modulator is realized using a high-speed switched-opamp (SO) technique with a sampling frequency of up to 50 MHz, which is improved ten times more than prior 1 V SO designs and comparable to the performance of the state-of-the-art SC circuits that operate at much higher supply voltages. On the system level, a fast-settling double-sampling SC biquadratic filter architecture is proposed to achieve high-speed operation. A low-voltage double-sampling finite-gain-compensation technique is employed to realize a high-resolution /spl Sigma//spl Delta/ modulator using only low-DC-gain opamps to maximize the speed and to reduce power dissipation. On the circuit level, a fast-switching methodology is proposed for the design of the switchable opamps to achieve a switching frequency up to 50 MHz. Implemented in a 0.35-/spl mu/m CMOS process (V/sub TP/=0.82 V and V/sub TN/=0.65 V) and at 1 V supply, the modulator achieves a measured peak signal-to-noise-and-distortion ratio (SNDR) of 42.3 dB at 10.7 MHz with a signal bandwidth of 200 kHz, while dissipating 12 mW and occupying a chip area of 1.3 mm/sup 2/.     

Fuzzy rule-based classification of remotely sensed imagery

The purpose of this paper is to investigate the applicability of fuzzy rule-based modeling to classify a LANDSAT TM scene from 1984 of an area located in the south of Germany. Both a land cover map with four different categories and an image depicting the degree of ambiguity of the classification for each pixel is the expected output. The fuzzy classification algorithm will use a rule system derived from a training set using simulated annealing as an optimization algorithm. The results are then validated and compared with a common classification method in order to judge the effectiveness of the proposed technique. It will also be shown that the proposed method with only nine rules for four different land cover classes performs slightly better than the maximum likelihood classifier (MLC). For error assessment, the traditional error matrix and fuzzy operators have been used     

Microscopic simulation of electronic noise in semiconductormaterials and devices

We present a microscopic interpretation of electronic noise in semiconductor materials and two-terminal devices. The theory is based on Monte Carlo simulations of the carrier motion self-consistently coupled with a Poisson solver. Current and voltage noise operations are applied and their respective representations discussed. As application we consider the cases of homogeneous materials, resistors, n⁺nn ⁺ structures, and Schottky-barrier diodes. Phenomena associated with coupling between fluctuations in carrier velocity and self-consistent electric field are quantitatively investigated for the first time. At increasing applied fields hot-carrier effects are found to be of relevant importance in all the cases considered here. As a general result, noise spectroscopy is found to be a source of valuable information to investigate and characterize transport properties of semiconductor materials and devices     

Current-mode A/D converter

The authors report the design of a new current-mode A/D converter, based on a modified successive-approximations model, in 1.2 μm CMOS technology. The proposed circuit is characterised by good accuracy and fast dynamic performance, low power consumption and small occupation area. SPICE simulations allow the design approach to be validated and the electrical performance of the ADC to be predicted     

Filter matrix estimation in automated DNA sequencing

In four-color fluorescence-based automated DNA sequencing, a 4×4 filter matrix parameterizes the relationship between the dye-intensity signals of interest and the data collected by an optical imaging system. The filter matrix is important because the estimated DNA sequence is based on the dye intensities that can only be recovered via inversion of the matrix. Here, the authors present a calibration method for the estimation of the columns of this matrix, using data generated through a special experiment in which DNA samples are labeled with only one fluorescent dye at a time. Simulations and applications of the method to real data are provided, with promising results     

The pharmacokinetics of pancuronium bromide in infants, children and adults

Laparoscopic retroperitoneal lymph node dissection is a new surgical procedure used to enhance staging in men with clinical stage I nonseminomatous germ cell tumors of the testis. The procedure has been performed in a limited number of patients at several centers with extensive laparoscopic experience. Laparoscopic retroperitoneal lymphadenectomy is a technically demanding procedure which can be successfully completed in the majority of patients. However, the risk of complications is greater than in patients who undergo standard open retroperitoneal lymph node dissection. The primary advantage of a laparoscopic approach is shortened hospitalization and rapid return to normal activity. The role of laparoscopy in the management of patients with testis malignancy has not been defined. The use of this staging procedure may help minimize the need for surveillance studies following surgery and may be best utilized in men with a lower likelihood of nodal metastases. Ultimately, prospective study in large groups of patients will be necessary to determine the role of laparoscopic retroperitoneal lymph node dissection in patients with testis cancer.     

Efficient diode-pumped single-frequency erbium:ytterbium fiberlaser

We report a 7.6-mW single-frequency fiber laser operating at 1545 nm, using for the first time an Er³⁺:Yb³⁺ doped fiber and a fiber grating output coupler. The laser did not exhibit self-pulsation, which is a typical problem in short three-level fiber lasers, and had a relative intensity noise (RIN) level below -145.5 dB/Hz at frequencies above 10 MHz. The linewidth of the laser was limited by the relaxation oscillation sidebands in the optical spectrum and was typically less than 1 MHz