Molecular weight effect on the obtainment of parallel and perpendicular orientation in thermotropic poly(diethylene glycol <Emphasis Type="Italic">p,p′</Emphasis>-bibenzoate)

Summary The effect of molecular weight on the uniaxial orientation process has been analyzed in two samples of thermotropic poly(diethylene glycol p,p′-bibenzoate), evaluating the influence of that parameter on the type of orientation obtained. Several strain rates and deformation temperatures have been tested in order to map out the conditions for obtaining the two different kinds of orientation. The results show that in the lower molecular weight PDEB sample (M_w=31200) it is rather easy to get exclusively perpendicular “anomalous” orientation, with the molecular axes aligned transversely to the stretching direction. However, it is extremely difficult to obtain 100% parallel “normal” orientation. On the contrary, either type of orientation or a mixture of them can be easily developed for the higher molecular weight PDEB sample (M_w=102900).     

Evaluating the mixing performance of a ribbon blender

This paper investigates the effects of processing and equipment parameters of a ribbon blender (i.e. loading method of lubricant, fill level, blade speed and blade design) on magnesium stearate homogeneity. A core sampling technique is used to obtain at least one hundred samples per sampling event, which are extracted throughout the blender and yield a thorough characterization of the entire bed. The results presented here can be used as a guideline to develop appropriate blending processes and characterization protocols for ribbon blenders.     

Luminescence from praseodymium doped AlN thin films deposited by RF magnetron sputtering and the effect of material structure and thermal annealing on the luminescence

Thin films of Praseodymium doped AlN are deposited on silicon (111) substrates at 77 K and 950 K by rf magnetron sputtering method. About 500–1000 nm thick films are grown at 100–200 watts RF power and 5–8 mTorr nitrogen, using a metal target of Al with Pr. X-rays diffraction results show that films deposited at 77 K are amorphous and those deposited at 950 K are crystalline. Cathodoluminescence studies are performed at room temperature and luminescence peaks are observed in a wide range from ultraviolet to infrared region. The most intense peak is obtained in green at 526 nm from amorphous films as a result from ³P₁→³H₅ transition. In crystalline films the intense peak was obtain in red at 648 nm as a result from ³P₀→³F₂ transition. Films are thermally activated at 1300 K for half an hour in a nitrogen atmosphere. Thermal activation enhances the intensity of luminescence. Two peaks at 488 nm and 505 nm merged after thermal activation, giving rise to a single peak at 495 nm.     

Effect of heat treatment in air on the thermal properties of SiC fibre reinforced composite: Part 2 A magnesium aluminium silicate (MAS) matrix glass ceramic composite

The thermal properties of a magnesium aluminium silicate (MAS) glass ceramic matrix composite reinforced by SiC (Nicalon) fibres have been investigated before and after heat treatment in the temperature range 600–1,200 °C. Within this temperature range, during the heat treatment at lower temperatures such as 600 and 700 °C, the oxidation of the carbon layer occurred and mixture of silicon and carbon was formed in the interface. This results in a decrease in thermal diffusivity values. After heat treatment at the temperatures higher than 1,000 °C, the carbon layer was thickened and resulted in the higher thermal diffusivity values.     

Optimizing simultaneously over the numerator and denominator polynomials in the Youla-Kuc/spl caron/era parametrization

Traditionally, when approaching controller design with the Youla-Kuc/spl caron/era parametrization of all stabilizing controllers, the denominator of the rational parameter is fixed to a given stable polynomial, and optimization is carried out over the numerator polynomial. In this note, we revisit this design technique, allowing to optimize simultaneously over the numerator and denominator polynomials. Stability of the denominator polynomial, as well as fixed-order controller design with H/sub /spl infin// performance are ensured via the notion of a central polynomial and linear matrix inequality (LMI) conditions for polynomial positivity.     

Measurement of the density and surface tension of Ni-based superalloys in the liquid and mushy states

The densities of three Ni-based superalloys have been measured in both liquid and mushy states by both a modified sessile drop method (MSDM) and a modified pycnometric method (MPM) for alloys CMSX-4 and CM186LC, and for CMSX-10 alloy by MSDM only. The surface tensions of liquid CMSX-4, CM186LC, and CMSX-10 superalloys were measured using the sessile drop method. All measurements were carried out in a highly purified argon atmosphere with the oxygen partial pressure of less than 10⁻¹⁹ MPa in the gas outlet. The densities of all superalloys in both liquid and mushy states were found to decrease with increasing temperature. The volume thermal expansion of each superalloy in the mushy state was found to be higher than that in the liquid state. The densities determined by different methods have been critically assessed and recommended values in both liquid and mushy states are given as a linear function of temperature for the three Ni-based superalloys. The surface tension of liquid CMSX-4 superalloy was found to decrease with increasing temperature, while that of liquid CMSX-10 superalloy increases with increasing temperature. The wetting behavior of liquid CM186LC on the alumina substrate was found (1) to differ significantly from that of CMSX-4 and CMSX-10 and (2) to vary with time. A HfO₂-rich layer was found in the contact area of CM186LC with the alumina substrate, which could lead to some uncertainty in the value obtained for the surface tension determined for CM186LC.     

3D velocity from 3D Doppler radial velocity

We present local least squares and regularization frameworks for computing 3D velocity (3D optical flow) from 3D radial velocity measured by a Doppler radar. We demonstrate the performance of our algorithms quantitatively on synthetic radial velocity data and qualitatively on real radial velocity data, obtained from the Doppler radar at Kurnell Radar station, Botany Bay, New South Wales, Australia. Radial velocity can be used to predict the future positions of storms in sequences of Doppler radar datasets.© 2005 Wiley Periodicals, Inc. Int J Imaging Syst Technol, 15, 189–198, 2005     

Russian underwater tunnels in the system of international transportation ways

Sustained world economic development trends characteristic with international trade annual growth rate of 7–8% along with considerable dynamics in the interregional goods circulation sphere on one hand and vast territory of Russia combined with a relatively developed railway network on the other hand provide a unique chance for this country to arrange land transportation routes alternative and competitive in comparison with existing marine routes. Construction of rail tunnels seems to be most efficient means for transportation corridors to cross-wide water areas like Nevelsky Strait (10.5 km) between the mainland and the Sakhalin Island in Russia, Bering Strait (92 km) between Chukotka Peninsula (Russia) and Alaska (USA). The tunnels construction conditions, structures and technologies planned to be used are considered in the paper.     

Microstructures formed by spray freezing of food fats

The spray-freezing of two food fats, tripalmitin (PPP) and cocoa butter (CB) and mixtures thereof, has been modeled experimentally using a novel single droplet freezing apparatus configured so that temperature profiles or samples for microstructure analysis can be obtained. For 2 mm diameter droplets suspended in a cold air flow at temperatures around 2–15°C, initial cooling rates were on the order of 10 K s⁻¹ and the temperature profiles could be correlated directly to DSC data collected at 20 K min⁻¹, indicating that minimal supercooling of the materials occurred in the droplet form. Microstructure analysis confirmed that PPP crystallized preferentially in mixtures, and that the surface structure was very sensitive to storage conditions. The bulk structure was much less sensitive, and the internal microstructure of the PPP droplets revealed distinct nucleation sites, which were absent from the CB: These persisted in the mixtures up to 50 wt%. X-ray analysis indicated that the fats crystallized in their more stable forms, namely, β for PPP and Form V/V1 in CB.     

Growth of highly orientated strontium barium niobate thin films on Si substrates through the sol–gel process using a K: SBN template layer

We report the growth of highly C-axis orientation of Sr _x Ba_1−x Nb₂O₆ (SBN) thin films on p-type (100) Si substrates by using a potassium-substituted SBN template layer with the sol–gel method. The crystallization of SBN thin films was found closely related to the potassium ion doping concentration and the postannealing temperature of the K-SBN template layer. Secondary ion mass spectrometry analysis showed that potassium elements were accumulated at the interface of the template layer and silicon substrate. SBN films postannealed at 750 °C with K-SBN template layer has a smaller full width at half maximum of X-ray rocking curve of 2.45° than that of 5.40° for the pure SBN films. By introducing a template layer, the surface morphologies of SBN films fabricated on silicon substrate were greatly improved.