Brake wear from vehicles as an important source of diffuse copper pollution.

In this article we show that brake wear from road traffic vehicles is an important source of atmospheric (particulate) copper concentrations in Europe. Consequently, brake wear also contributes significantly to deposition fluxes of copper to surface waters. We estimated the copper emission due to brake wear to be 2.4 kiloton per year. For comparison, the official database for Europe (without brake wear) totals 2.6 kiloton per year. In Western Europe the brake wear emissions dominate the total emission of copper. Using the spatially resolved emission data, copper distributions over Europe were calculated with the LOTOS-EUROS model. Without brake wear the model underestimates observed copper concentrations by a factor of 3, which is in accordance with other studies. Including the brake wear emissions largely removes the bias. We find that 75% of the atmospheric copper input in the North Sea may be due to brake wear. We estimate that about 25% of the total copper input in the Dutch part of the North Sea stems from brake wear. Although the estimated brake wear copper emission is associated with a large uncertainty, it significantly improves our understanding of the copper cycle in the environment.     

Microprocessor testability

As the level of microprocessor complexity increases to several hundred thousand transistors for a single-chip machine, it is becoming very difficult to test commercially available designs to the level of fault coverage desired by some customers. In order to achieve near 100-percent coverage of single stuck-at faults, future microprocessors must be designed with special testing features (designed for testability). The authors describe the testing problem for microprocessors, including the various methods of generating test sets and their application by the user. A survey of the testability features of some of today's commercially available microprocessors is presented. Suggestions for testability features for future-generation microprocessors are also discussed     

IPv6 delay and loss performance evolution

Although packet delay and loss are two important parameters of the Internet performance, to the best of our knowledge, the evolution of large‐scale IPv6 delay and loss performance has previously not been studied. In this paper, we analyze more than 600 end‐to‐end IPv6 paths between about 26 testboxes of RIPE Network Coordination Centre over two years, and compare the delay and loss performance over time with their IPv4 counterparts. We present and discuss the measurement methodologies and show that IPv6 paths have a higher delay and loss than their IPv4 counterparts. The main reason for the worse performance stems from IPv6‐in‐IPv4 tunnels rather than from native IPv6 paths and such tunnels are still widely used today. Copyright © 2007 John Wiley & Sons, Ltd.     

A Radiation Imaging Detector Made by Postprocessing a Standard CMOS Chip

An unpackaged microchip is used as the sensing element in a miniaturized gaseous proportional chamber. This letter reports on the fabrication and performance of a complete radiation imaging detector based on this principle. Our fabrication schemes are based on wafer-scale and chip-scale postprocessing. Compared to hybrid-assembled gaseous detectors, our microsystem shows superior alignment precision and energy resolution, and offers the capability to unambiguously reconstruct 3D radiation tracks on the spot.     

Influence of Production Process Parameters on Fish Oil Quality in a Pilot Plant

ABSTRACT: A pilot plant used for upgrading herring byproducts into fish oil was analyzed on its operational efficiency and product quality. The temperature of the heat exchanger and the speeds of the pump and the 3-phase decanter were varied according to a 2³ fractional factorial design. The initial amount of oxidation products present in the crude oil, its storage stability, and the yields from the different obtained products were determined. Multivariate data analysis of the advanced screening stage showed that T had neither influence on the quality nor on the yield in contrast to D and MP (P < 0.05). Process optimization results showed that the quality of the oil was influenced by an interaction effect between the speed of the MP and the D. Oils processed with the highest MP speed were the most stable during storage.     

Photonic Demodulator With Sensitivity Control

A current assisted photonic demodulator for use as a pixel in a 3-D time-of-flight imager shows nearly 100% static demodulator contrast and is operable beyond 30 MHz. An integrated tunable sensitivity control is also presented for increasing the distance measurement range and avoiding unwanted saturation during integration periods. This is achieved by application of a voltage on a dedicated drain tap showing a quenching of sensor sensitivity to below 1%     

Thermoelectric Converters of Human Warmth for Self-Powered Wireless Sensor Nodes

Solar cells are the most commonly used devices in customer products to achieve power autonomy. This paper discusses a complementary approach to provide power autonomy to devices on a human body, i.e., thermoelectric conversion of human heat. In indoor applications, thermoelectric converters on the skin can provide more power per square centimeter than solar cells, particularly in adverse illumination conditions. Moreover, they work day and night. The first sensor nodes powered by human heat have been demonstrated and tested on people in 2004-2005. They used the state-of-the-art 100-muW watch-size thermoelectric wrist generators fabricated at IMEC and based on custom-design small-size BiTe thermopiles. The sensor node is completed with a power conditioning module, a microcontroller, and a wireless transceiver mounted on a watchstrap     

Towards Testing Product Line Architectures

A product line architecture is a single specification capturing the overall architecture of a series of closely related products. Its structure consists of a set of mandatory elements and a set of variation points. Whereas mandatory elements are part of the architecture of every product in the product line architecture, variation points precisely define the dimensions along which the architectures of individual products differ from each other.The increased use of product line architectures in today's software development projects poses several challenges for existing testing techniques. In this paper we discuss those challenges and discuss what we believe are opportunities for addressing them.     

Systems that Should Have Failed: Critical Infrastructure Protection in an Institutionally Fragmented Environment

Recent years have witnessed major governmental initiatives regarding critical infrastructure protection (CIP). During that same time, critical infrastructures (CIs) have undergone massive institutional restructuring under the headings of privatization, deregulation and liberalization. Little research has gone into understanding the interactions between these two developments. In this article, we outline the consequences of institutional restructuring for the changing ways in which CIs ensure the reliability and security of their networks and services. Neither Normal Accident Theory nor High‐Reliability Theory can account for reliability under these conditions. We then investigate the implications of these findings for CIP.