Smooth and Vertical Facet Formation for AlGaN-Based Deep-UV Laser Diodes

Using a two-step method of plasma and wet chemical etching, we demonstrate smooth, vertical facets for use in Al _x Ga_1−x N-based deep-ultraviolet laser-diode heterostructures where x = 0 to 0.5. Optimization of plasma-etching conditions included increasing both temperature and radiofrequency (RF) power to achieve a facet angle of 5 deg from vertical. Subsequent etching in AZ400K developer was investigated to reduce the facet surface roughness and improve facet verticality. The resulting combined processes produced improved facet sidewalls with an average angle of 0.7 deg from vertical and less than 2-nm root-mean-square (RMS) roughness, yielding an estimated reflectivity greater than 95% of that of a perfectly smooth and vertical facet.     

Five channel WDM soliton pulse generation using sinusoidally drivenelectroabsorption modulators in 16×1 laser/modulator array

Five wavelength multiplexed pulse streams are generated in an integrated 16×1 laser modulator array by sinusoidally driving five of the potential 16 electroabsorption modulators. At a repetition rate of 2.5 GHz, near transform-limited pulses spaced in wavelength over 7.6 nm are observed. Pseudorandom coding of one channel is achieved by applying an electrical RZ data signal to the modulator     

Indium Gallium Arsenide Quantum Dot Gate Field-Effect Transistor Using II–VI Tunnel Insulators Showing Three-State Behavior

This paper presents an indium gallium arsenide (InGaAs) quantum dot gate field-effect transistor (QDG-FET) that exhibits an intermediate “i” state in addition to the conventional ON and OFF states. The QDG-FET utilized a II–VI gate insulator stack consisting of lattice-matched ZnSe/ZnS/ZnMgS/ZnS/ZnSe for its high-κ and wide-bandgap properties. Germanium oxide (GeO _x )-cladded germanium quantum dots were self-assembled over the gate insulator stack, and they allow for the three-state behavior of the device. Electrical characteristics of the fabricated device are also presented.     

Novel Quantum Dot Gate FETs and Nonvolatile Memories Using Lattice-Matched II–VI Gate Insulators

This paper presents the successful use of ZnS/ZnMgS and other II–VI layers (lattice-matched or pseudomorphic) as high-k gate dielectrics in the fabrication of quantum dot (QD) gate Si field-effect transistors (FETs) and nonvolatile memory structures. Quantum dot gate FETs and nonvolatile memories have been fabricated in two basic configurations: (1) monodispersed cladded Ge nanocrystals (e.g., GeO _x -cladded-Ge quantum dots) site-specifically self-assembled over the lattice-matched ZnMgS gate insulator in the channel region, and (2) ZnTe-ZnMgTe quantum dots formed by self-organization, using metalorganic chemical vapor-phase deposition (MOCVD), on ZnS-ZnMgS gate insulator layers grown epitaxially on Si substrates. Self-assembled GeO _x -cladded Ge QD gate FETs, exhibiting three-state behavior, are also described. Preliminary results on InGaAs-on-InP FETs, using ZnMgSeTe/ZnSe gate insulator layers, are presented.     

Compact Harmonic Filter Design and Fabrication Using IPD Technology

An integrated passive device (IPD) technology has been developed to meet the ever increasing needs of size and cost reduction in radio front-end transceiver module applications. Electromagnetic (EM) simulation was used extensively in the design of the process technology and the optimization of inductor and harmonic filter designs and layouts. Parameters such as inductor shape, inner diameter, metal thickness, metal width, and substrate thickness have been optimized to provide inductors with high quality factors. The technology includes 1) a thick plated gold metal process to reduce resistive loss; 2) MIM capacitors using PECVD SiN dielectric layer; 3) airbridges for inductor underpass and capacitor pick-up; and 4) a 10 mil finished GaAs substrate to improve inductor quality factor. Both lumped element circuit simulations and electromagnetic (EM) simulations have been used in the harmonic filter circuit designs for high accuracy and fast design cycle time. This paper will present the EM simulation calibration and demonstrate the importance of using EM simulation in the filter design in order to achieve first-time success in wafer fabrication. The fabricated IPD devices have insertion loss of 0.5 dB and harmonic rejections of 30dB with die size of 1.42 mm for high band (1710 MHz-1910 MHz) and 1.89 mm for low band (824-915 MHz) harmonic filters.     

Simultaneous chromizing-aluminizing coating of austenitic stainless steels

Chromium and aluminum were simultaneously co-deposited by diffusion into austenitic stainless steel substrates, by a single-step, pack-cementation process. The mechanism for the formation of diffusion-coated products on 304 and 316 stainless steels and on Incoloy 800 is discussed. The morphologies of the phases formed at the surface, i.e., an external beta layer and an underlying multiphase interdiffusion zone, are presented. The formation of the brittle, , outer layer was minimized by variations in the pack composition and activator. The coated 304 and 316 steels exhibited excellent scaling resistance upon oxidation in air at 1000°C.     

A comprehensive approach to the analysis of contrast enhanced cardiac MR images

Current magnetic resonance imaging (MRI) technology allows the determination of patient-individual coronary tree structure, detection of infarctions, and assessment of myocardial perfusion. Joint inspection of these three aspects yields valuable information for therapy planning, e.g., through classification of myocardium into healthy tissue, regions showing a reversible hypoperfusion, and infarction with additional information on the corresponding supplying artery. Standard imaging protocols normally provide image data with different orientations, resolutions and coverages for each of the three aspects, which makes a direct comparison of analysis results difficult. The purpose of this work is to develop methods for the alignment and combined analysis of these images. The proposed approach is applied to 21 datasets of healthy and diseased patients from the clinical routine. The evaluation shows that, despite limitations due to typical MRI artifacts, combined inspection is feasible and can yield clinically useful information.     

Remote Estimation of Crop Chlorophyll Content Using Spectral Indices Derived From Hyperspectral Data

This paper examines the use of simulated and measured canopy reflectance for chlorophyll estimation over crop canopies. Field spectral measurements were collected over corn and wheat canopies in different intensive field campaigns organized during the growing seasons of 2004 and 2005. They were used to test and evaluate several combined indices for chlorophyll determination using hyperspectral imagery (Compact Airborne Spectrographic Imager). Several index combinations were investigated using both PROSPECT-SAILH canopy simulated spectra and field-measured reflectances. The relationships between leaf chlorophyll content and combined optical indices have shown similar trends for both PROSPECT-SAILH simulated data and ground-measured data sets, which indicates that both spectral measurements and radiative transfer models hold comparable potential for the quantitative retrieval of crop foliar pigments. The data set used has shown that crop type had a clear influence on the establishment of predictive equations as well as on their validation. In addition to generating different predictive equations, corn and wheat data yielded contrasting agreement between estimated and measured chlorophyll contents even for the same predictive algorithm. Among the set of indices tested in this paper, index combinations like modified chlorophyll absorption ratio index/optimized soil-adjusted vegetation index (OSAVI), triangular chlorophyll index/OSAVI, moderate resolution imaging spectrometer terrestrial chlorophyll index/improved soil-adjusted vegetation index (MSAVI), and red-edge model/MSAVI seem to be relatively consistent and more stable as estimators of crop chlorophyll content.     

Electric drive subsystem for a low-storage requirement hybridelectric vehicle

Integrating an electric machine drive system into the powertrain of a hybrid electric vehicle (HEV) represents a challenging exercise in packaging complex electromechanical and power electronic subsystems. The Ford combined alternator starter (FCAS) and its attendant power and control electronics are physically partitioned because power electronics has not yet evolved to the stage in which fully packaged drives can be realized. A similar situation exists for the control and sensor subsystems necessary for a fully functional high-performance drive. Hardware partitioning requires that more attention be given to installation issues and to mitigating system interactions. The FCAS system consists of an integrated starter/alternator (S/A), an S/A module (SAM), and a vehicle electrical infrastructure that can support the power and energy levels demanded. Our field experience with the FCAS system is presented along with test results obtained from vehicle operation     

The Multi-angle Imaging SpectroRadiometer science data system, its products, tools, and performance

Ground processing of data from the Multi-angle Imaging SpectroRadiometer (MISR) instrument, part of NASA's Earth Observing System (EOS), exploits new and unique science algorithms not previously used operationally. A range of data products from Level 1 through Level 3 is being produced. Because of MISR's unprecedented design, extensive prototyping was required from a relatively early stage. The data throughput is large, necessitating an innovative software design approach that maximizes performance. The systematic science processing software was developed at the Jet Propulsion Laboratory, with data processing occurring at the NASA Langley Research Center using the EOS Core System, a collaborative arrangement that works well. With the availability of actual mission data following launch on the Terra spacecraft in December 1999, MISR's computational needs have become better known, and many improvements have been made to both the science software and the production system to achieve a successful overall data processing capability. This paper provides information about MISR data for the science user, and describes the nature and scope of implementation and operations activities.