Study on Microstructure and Mechanical Properties of Hot Rolled Low Silicon Containing Phosphorus TRIP Steel

The effects of final air cooling temperature on the microstructure and mechanical properties of hot rolled 0.2C-1.9Mn-0.5Si-0.08P TRIP steel were studied by utilizing OM, SEM, TEM and tensile tests. Experimental results showed that in the multiphase microstructure of the investigated steel when the finish rolling temperature was about 820 ℃ and the final air cooling temperature was in the range of 630-700 ℃, the grain size of most of ferrite was finer (about 4 μm) and which had higher dislocation density, t...     

Study on Thermal Deformation Behavior and Properties of Vacuum Hot-press Sintered W(50)/Cu-Al_2O_3 Composite

In this work, the tungsten particulate reinforced Al2O3 dispersion strengthened copper base composites were successfully fabricated by using a vacuum hot-press sintering method. With the test temperature varying from 650 to 950 ℃ and the strain rate varying from 0.01 to 5 s-1, the W(50)/Cu-Al2O3 composites were isothermally compressed on a Gleeble-1500D thermal simulator. The true stress-strain curves of the W(50)/Cu-Al2O3 under different test conditions were obtained. The dynamic recrystallization of the W...     

Transition Temperature of Bi_2Sr_2CaCu_2O_(8+x) Superconducting Films Prepared from Commercial Precursors

This paper have made a systematic study of the superconducting Bi-2212 phase transition temperature, which has a transition temperature (Tc) around 80-93 K, and depends on precise control of synthesis conditions, mainly including heat treatment parameters, oxygen partial pressure, and annealing temperature. Partial melting of the sample during preparation helps to raise its Tc. To elucidate the origin of this strong effect, the samples were heated with different melting process. The rapid changes in Tc valu...     

Development of High Deformability Pipeline Steel

Based on strain-based design, high deformability X70 high strength pipeline steel with dual-phase microstructure has been developed, which can be laid in the seismic, the cold or the deepwater region. The results illustrated that the developed X70 steel has the stress-strain curve like round house and it shows good anti-transformation characteristic, high uniform deformation(≥10%), enhanced n-value(≥0.10), and the low yield-tensile ratio Y/T(≤0.85). The dual-phase microstructure of ferrite and bainite conta...     

An experimental study on self-output-control characteristics of micro downwind rotor with coning soft blades

In this short paper,we have treated the aerodynamic performance of micro downwind rotor with coning soft blades experimentally.The test wind rotor has the tip diameter of 1.5 m and three two-dimensional NACA0018 blades of 0.15 m chord whose material is light,soft and pliable foam plastic for perfect safety.From the wind tunnel test,it is realized that the performance is manageable by the coning angle of the rotor blade.In the present case,an improvement of the performance in lower wind speeds is achieved by...     

Research on forecasting model of sandstone deformation rate during sine wave loading segment under the lag effect

To reduce data variance caused by individual differences of different samples,a new experimental method is proposed by loading and unloading the axial forces with different frequencies and different waves of a certain load amplitude to the same rock sample without damaging it.Lag time segments are defined and fractionized into segments I and Ⅱ.Criterions for seg-mentation,definitions of relevant parameters and empirical analysis are also offered afterwards.In the course of sinusoidal loading,the serious pea...     

Effect of heat treatment on mechanical properties of heavily cold-rolled Fe-6.5wt%Si alloy sheet

Fe-6.5wt%Si alloy has excellent soft magnetic properties,but it is hard to be cold-rolled due to appearance of ordered phases in this alloy.In this paper we report that ultra thin Fe-6.5wt%Si sheet of 0.05 mm thick was obtained by heavily cold rolling.By means of optical microscope,micro-hardness indenter,instron,SEM and X-ray diffraction,the effect of heat treatment on mechanical properties of this alloy sheet was investigated.The heavily cold-rolled sheet exhibits some extent of ductility.The ultimate ten...     

基于数学形态学的围棋棋群聚类算法

计算机围棋可以模拟人类棋手的棋群聚类能力以提高搜索效率。本研究以数学形态学为工具,在形式化基础上采用带有限制条件的膨胀运算进行棋群的初步聚类,结合其它一些启发式搜索方法完成棋群的最终聚类,并结合实战对局评价了此算法的性能,指出了此算法的应用价值。     

微型减压设施与磨盘柿保鲜效果研究

为使减压贮藏推广与应用,从降低成本出发,对比分析了关键配件的选择,并探讨磨盘柿在微型减压设施下的保鲜效果。结果表明,微型减压设施的配件应选用直径250 mm的硬质PVC波纹耐真空单管,圆形垛,宽3 m、厚0.1 mm软质PVC薄膜,并采用套扣、缠生料带和抹玻璃胶方式连接普通加厚双镀锌铁管、普通加厚黑胶管和内含钢丝的软塑料管形成真空连接系统。这套微型减压设施有利于磨盘柿果实硬度的保持,抑制可溶性固形物、膜相对透性及贮藏后期的丙二醛含量的升高,延缓果实的衰老进程,抑制果实后期褐变的发生。     

工程陶瓷边缘碎裂行为与机理研究进展

边缘碎裂是工程陶瓷磨削加工过程中的常见现象,是影响陶瓷元件加工质量和加工成本的关键因素之一。由于所处几何位置的特殊性,传统陶瓷磨削理论难以直接解释边缘碎裂行为的特有现象及规律,研究陶瓷等脆性材料的边缘碎裂行为与机理成为当今加工界的热点之一。综述了工程陶瓷边缘碎裂行为与机理的最新研究进展,详细阐述了工程陶瓷的边缘碎裂剥落模型、边缘碎裂单晶压头模型和边缘碎裂划痕模型,并对各模型的优缺点作了评价,提出了工程陶瓷边缘碎裂行为与机理研究中尚待解决的问题以及边缘碎裂预防措施。