Design, modeling, and hardware correlation of a 3.2Gb/s/pair memory channel

With the rapid advance of silicon process technology, it is now possible to design input/output (I/O) circuits that operate at multigigabit data rates. As a result, accurate modeling and analysis of high-speed interconnect systems is essential to optimize the performance of the overall system. This paper describes the interconnect design, modeling, simulation, and characterization methodologies that are essential to achieve multigigabit data rates. It focuses on the physical layer verification and hardware correlation of functional systems and silicon to ensure robust system operation over 3.2Gb/s data rate using conventional low-cost packaging and printed circuit board (PCB) technologies. In order to capture conductor and dielectric losses, as well as other high-frequency effects of three-dimensional structures, accurate measurement-based simulation techniques that directly incorporate frequency-domain parameters from measurement or electromagnetic solver parameters into circuit simulation tools using fast Fourier transform (FFT) and bandlimiting windowing techniques are developed. Finally, simulation waveforms are correlated with prototypes at both component and system levels in both time and frequency domains.     

Possible tactics to improve the growth of single-walled carbon nanotubes by chemical vapor deposition

The growth time, growth mode and the method of preparing the supported catalysts play an important role in the growth of single-walled nanotubes (SWNTs). Their effects on the chemical vapor deposition (CVD) growth of SWNTs with MgO-supported catalysts were investigated in this study. It is shown that the growth rate of SWNTs was large during the initial few minutes of growth, however the quality of the tubes was low owing to the formation of many defects. Long term growth may favor the formation of tubes with high quality and high yield, but the introduction of other forms of carbon (impurities) is also unavoidable. There was a balance between the increase in yield and quality and sacrifice of the purity during growth of SWNTs. MgO-supported catalysts prepared by the co-precipitation method were found to be more effective for the synthesis of SWNTs than those prepared by the widely used impregnation method. The size and dispersion state of the catalyst were found to be crucial in enhancing the growth of SWNTs. In addition, growth on the surface of SWNTs over nanosized catalyst films was shown to be more favorable for the synthesis of tube products with higher quality, yield and purity.     

Impedance boundary conditions in a hybrid FEM/MOM formulation

When numerically modeling structures with imperfect conductors or conductors coated with a dielectric material, impedance boundary conditions (IBCs) can substantially reduce the amount of computation required. This paper incorporates the IBC in the finite-element method (FEM) part of a FEM/method of moments (FEM/MoM) modeling code. Properties of the new formulation are investigated and the formulation is used to model three practical electromagnetic problems. Results are compared to either measured data or other numerical results. The effect of the IBC on the condition number of hybrid FEM/MoM matrices is also discussed.     

天康面粉公司制粉车间局部技改介绍

山东巨野国家粮食储备库天康面粉公司制粉车间始建于2000年,设计能力为处理小麦100t/d.主要设备有FMFQ10×2/6×2磨粉机8台,FS-FG6×24C高方筛3台,FQFD50×2×3清粉机2台,磨辊总接触长度12000 mm,平筛总筛理面积138.8 m2,单位磨辊接触长度12 mm/(100kg·d),单位平筛筛理面积0.14 m2/(100kg·d).麦间清理工艺(包括初清)为4筛2打2去石3磁选2着水,粉间工艺为488M1S2T4P3Br.     

小剂量辐照小鼠胸腺细胞膜流动性的变化

报道了以茈为荧光探针,探讨小剂量~(60)Co γ射线照射后小鼠胸腺细胞膜流动性的变化。结果表明,剂量在0.25-1.00Gy范围,胸腺细胞膜流动性降低与剂量之间呈明显线性关系。从0.50Gy起,辐照组荧光强度比值I_1/I_2与I_3/I_2与对照组的比较存有显著差异(P<0.05)。提示淋巴细胞膜流动性的变化可作为小剂量辐照早期效应的敏感指标。     

把中国建设成世界有色金属制造业基地的对策研究

本文首先介绍了我国有色金属工业的现状以及当前世界有色金属工业发展的新格局,并分析了中国成为世界有色金属制造业基地的支撑条件,最后提出了关于建设具有特色的中国有色金属制造业基地的几点看法。     

台达变频器在纺织织带盘带机上的应用

盘带机是纺织织带成品分卷设备，需要使用到收放卷控制。本文基于台达变频器在盘带机上的应用案例，论述盘带机自动化系统设计调试过程以及遇到的问题分析。     

一个基于J2EE Web应用的框架设计与实现

J2EE(Java 2平台企业版)是当前建立和开发各种Web应用的主流平台,MVC(模型-视图-控制)体系结构是当今设计交互式应用的事实标准.文中结合MVC在J2EE Web中的应用,通过电子政务系统开发实践,提出了一个具体的实现方案,描述了应用系统设计,给出了表示层、控制层、代理层、业务逻辑层、数据访问层和数据存储层等层次的明确划分,阐述了各层的功能作用以及层与层之间的关系,并针对具体业务给出了实现的部分具体内容,为在J2EE环境下开发结构良好、易于维护、易于扩展的Web应用提供了可行方案.     

Studies of substrate specificities of lipases from different sources

Although lipases are widely applied in a wide variety of reactions, available information on the factors that are responsible for the substrate specificities of lipases from different sources is scarce. In this paper, nine lipase‐producing microorganism strains were isolated from oil‐containing samples. The properties of these enzymes, including pH optima, temperature optima, thermal stability, and pH stability, vary significantly with the different sources from which these lipases were isolated. The substrate specificities of the nine lipases, including fatty acid and positional specificities, were also studied. The fatty acid specificities of the nine lipases were observably different toward 15 substrates with different carbon chain lengths, different saturation degrees and different side chains. The lipases from S₃ Penicillium citrinum (PCL), MJ₁ Aspergillus niger (ANL), MJ₂ Aspergillus oryzae (AOL), YM Bacillus coughing (BCL), S₉ Geotrichum candidum (GCL), and S₁₁ Candida lypolytica (CLL) showed the strongest specificities to short‐chain esters, and the other lipases showed strong selectivity for medium‐ or long‐chain and branched esters. The positional specificities were examined by analyzing the hydrolytic products of triolein catalyzed by the nine lipases, using TLC. The lipases can be mainly classified into two groups by their specificities for the ester bond at position 2 of triglycerides; one group can selectively hydrolyze the ester bond at position 2 of the triglycerides, the other group cannot. All these nine lipases were divided into four groups by hierarchical clustering analysis on the basis of the results of fatty acid and positional specificities.     

La改性的Ag/TS-1催化剂上丙烯选择氧化制环氧丙烷

在H2 和O2 混合气体存在下 ,在常压固定床、石英反应器上考察了La改性的Ag/TS - 1催化剂催化丙烯环氧化反应。研究结果表明 ,Ag和La负载在TS - 1上的先后顺序对丙烯环氧化反应有影响。H2 在丙烯气相氧化反应体系中起着重要的作用。