Critical aspects of sinter-hardening of prealloyed Cr–Mo steel

In recent years, growing demand for greater mechanical properties of PM steel components with competitive fabrication cost has led to significant innovations in different fields of powder metallurgy. Recent research has been focused on reaching higher performance with lower cost. To this end, the possibility of combining the conventional sintering and post-sintering processes for a particular powder composition has been introduced. Sinter-hardening is a result of the research conducted along this line. Elimination of any secondary operation such as quench-hardening by incorporating it in the sintering process (i.e. sinter-hardening) is of great interest, as it will lead to lower processing costs and equal, if not higher mechanical performance. However, to ensure the desired mechanical properties of the final component and robustness of the performance, critical aspects of the sinter-hardening process should be rigorously studied.Hence with specific attention to a Cr–Mo steel powder (FL-5305), this study deals with the influence of density on cooling rate, the effect of different sintering temperatures (e.g. 1120 °C and 1250 °C) on austenite grain size and consequently, hardenability. The microstructure development in sinter-hardened FL-5305 material has been analyzed and predicted by means of the available literature for solid steel and also using the commercial software (JMatPro 5.0) for materials assessment based on thermodynamic and kinetics modeling. Finally, inaccurate carbon control and its adverse impact on excessive formation of cementite have been addressed.     

Transparent,Stimuli‐Responsive Films from Cellulose‐Based Organogel Nanoparticles

The use of bio‐based nanoscaled cellulose for the construction of novel functional materials has progressed rapidly over the past years. In comparison to most of studies starting with the hydrophilic nanoscaled cellulose, surface‐stearoylated cellulose nanoparticles (SS‐CNPs) are used in this report for the construction of multifunctional, responsive films. SS‐CNPs with an average size of 115 ± 0.5 nm are obtained after the surface‐modification of cellulose under heterogeneous conditions. Crystalline cellulose core is present within SS‐CNPs according to solid‐state ¹³C nuclear magnetic resonance (NMR) spectroscopy. SS‐CNPs show excellent dispersibility in nonpolar solvents and form temperature‐responsive organogels in tetrahydrofuran (THF) at low temperature or after long time storage at room temperature. Moreover, transparent and self‐standing films of SS‐CNPs from their THF‐suspension show solvent‐responsive surface wettability and responsive shape‐memory property. SS‐CNPs can also be used for the fabrication of nanocomposite films together with nonpolar compounds, such as (2‐stearoylaminoethyl) rhodamine B. Thus, these novel SS‐CNPs derived from sustainable cellulose fibers are promising candidates for the construction of novel functional materials.     

Indentation deformation and cracking behavior of hydrated aluminoborate glasses

Aluminoborate glasses have recently been found to feature high resistance to crack initiation during indentation due to a highly flexible network structure. In cesium aluminoborate glasses, it has been found that the use of a simple post-treatment, namely aging in a humid atmosphere, can further improve this resistance. To better understand the mechanical properties of this glass family upon humid aging, we here study the effect of aging conditions on the structure and mechanical properties of Li,K,Cs-aluminoborate glasses. As expected, we find that higher humidity and longer aging time cause more pronounced permeation of atmospheric water into the glasses. Due to their denser structure and stronger modifier-oxygen bonds, the humid aging has a relatively smaller effect on the mechanical properties of Li- and K-containing glasses relative to Cs-containing glasses, with the latter achieving an ultrahigh crack resistance. We find that the humid aging leads to the formation of a hydration layer in the Cs-aluminoborate glass surface, with a thickness of around 26 μm upon aging at 23 °C with 40% relative humidity for 7 days. Moreover, a remarkable indentation behavior, that is, the observation of μm-sized shear bands inside the imprint of the Cs-glass upon aging at 60% relative humidity is reported. Taken as a whole, the work provides guidelines for how to control the humid aging rate as a function of relative humidity and temperature to form a hydration layer and thus achieve improved crack resistance in such glasses.     

Enhanced performance in the deteriorated area of multicrystalline silicon wafers by internal gettering

The deteriorated area of the multicrystalline silicon (mc‐Si) ingots grown by directional solidification, commonly known as the Red Zone, is usually removed before wafering. This area, characterized by poor minority carrier lifetime, is located on the sides, at the top, and the bottom of the mc‐Si ingots. In this study, the effect of internal gettering by oxygen precipitates and structural defects has been investigated on the bottom zone of a mc‐Si ingot. Nucleation and growth of oxygen precipitates as well as low temperature annealing were studied. Photoluminescence imaging, lifetime mapping, and interstitial iron measurements performed by μ‐PCD reveal a considerable reduction of the bottom Red Zone. An improvement of lifetime from below 1 µs to about 20 µs and a reduction of interstitial iron concentration from 1.32 × 10¹³ at/cm³ to 8.4 × 10¹⁰ at/cm³ are demonstrated in this paper. Copyright © 2013 John Wiley & Sons, Ltd.     

Micro-Raman imaging of heterogeneous polymer systems: General applications and limitations

This article assesses the use of micro-Raman imaging with respect to polymer science. This relatively novel technique allows, at high spatial resolution, the acquisition of chemical and morphological information over an area of a sample. Using Raman imaging by confocal laser line scanning, a wide range of problems in polymer analysis has been studied to outline the capabilities and limitations of the technique. Three ternary polymer blends consisting of polypropene/polyethene/ethene-propene copolymer, polybutyleneterephthalate/polycarbonate/very low density polyethene, and styrene-co-acrylonitrile/styrene-co-maleicanhydrate/poly-2,6-dimethylphenylene oxide were studied with regard to compositional and morphological heterogeneities. In a binary polymer blend consisting of two different acrylate monomers, the refractive index profile established after artificially induced diffusion of the main components was determined from the concentration gradients. The distribution of unreacted free melamine in a cured melamine-formaldehyde resin was analyzed. Furthermore, the general structure of a composite sample consisting of polyethene fibers in an epoxide matrix was studied. Raman imaging proved suitable for the characterization of heterogeneities in composition and morphology on a size scale equal to or larger than 1 μm. In this sense, the technique helps to close the gap between infrared microscopy, with its comparatively poor spatial resolution, on the one hand, and transmission electron microscopy, with its limited chemical information, on the other hand. For heterogeneities on a submicron scale, the value of the technique is limited to the determination of average information. When combined with curve fitting, Raman imaging permitted us to determine the composition of the polypropene/polyethene/ethene-propene copolymer blend with an accuracy of 5–10%. The main limitations to micro-Raman imaging of polymer systems based on the confocal laser line scanning technique have been identified as the destruction of the samples due to insufficient heat dissipation of the high-incident laser power, interferences due to fluorescence, and the stability of the instrumentation during long collection times required for good signal-to-noise ratio spectra of weak Raman scatterers. © 1996 John Wiley & Sons, Inc.     

Modification of E-glass fiber surfaces with polyacrylic acid polymers from an aqueous solution

The research reported in the article focuses on modifying glass fiber surfaces with polyacrylic acid (PAA) compounds. E-glass fibers were treated with aqueous polyacrylic acid solution. Polyacrylic acid exchanges its protons with the ions present in the glass surface. Hydrolyzed metal cations may form salt complexes with the dissociated polyacrylic acid. Angular dependent electron spectroscopy for chemical analysis (ESCA) demonstrated that the atomic concentrations of aluminum and calcium in the glass fiber surface were constant throughout the analyzed interval. The cation exchange property of glass fiber was studied using direct current plasma (DCP), which showed that both calcium and aluminum ions were extracted by low concentration polycrylic acid solutions. ESCA studies of were extracted by low concentrationb polyacrylic acid solutions. ESCA studies of the PAA-treated glass fiber showed that the amount of PAA of the glass surface increases with increased acid concentration. A broadened and shifted ESCA peak of the carbon (0 CO) indicates the formation of salt complexes between the polyacrylic acid and metal ions on the glass surface. Polyacrylie acid was modified by an esterification reaction with glycidyl acrylate (GA) in aqueous solution in order to insert organofuctional groups into the PAA chain.     

Antioxidant capacity and total phenolics of <Emphasis Type="Italic">Cyphostemma digitatum</Emphasis> before and after processing: use of different assays

In the framework of standardisation of new healthy food sources, this paper aimed to study the total phenolics and the antioxidant power of Cyphostemma digitatum (Vitaceae) in water and ethanol extracts, using 96-well micro plates with BMG FLUOstar Optima micro plate reader. Total phenolics by Folin–Ciocalteu method in the water extracts were significantly lower after processing, decreasing from 1.41 ± 0.06 g GAE/100 g in the raw leaves to 0.80 ± 0.08 g GAE/100 g in the processed sample; the ethanol extract revealed the same trend with higher values, decreasing from 1.95 ± 0.03 to 1.56 ± 0.12 g GAE/100 g. The antioxidant capacity was elucidated by four methods: TEAC, DPPH, FRAP and ORAC. No or very weak correlations were found between antioxidant assays and total phenolics; this confirms that the antioxidant capacity could be attributed to other molecules. The ORAC assay proved to be more powerful than the other assays; it showed 103.3 ± 2.5 mmol/100 g Trolox equivalents in the raw leaves ethanol extract and 91.9 ± 3.0 mmol/100 g in the processed sample. ORAC assay showed the opposite for the water extract where the antioxidant capacity increased from 16.7 ± 0.2 to 41.7 ± 2.7 mmol/100 g Trolox equivalents after processing, which could be attributed to new water-soluble compounds generated in the consumed form.