IEA joint trials: New lessons from old plantations

Two international trials of potential biomass species families and clones planted in 1985 have been analyzed to determine changing patterns in growth, diseases, and insects. In the Swedish trial, with close spacing and short rotations, Salix viminalis clones gave the best average yield of 17.4 Mg/Ha/yr on the first coppice rotation. In the Minnesota, USA trial, with wider spacings and a longer rotation Populus alba hybrid clones gave the best average yields of 5.5 Mg/Ha/yr. The most important disease and insect problems encountered were Septoria musiva stem cankers on some Populus clones; frost die back in some Salix clones; and the leaf blotch miner, Fenusa dohrnii, on most Alnus families. Recommendations for future international cooperation in field trials are presented.     

Electrical characterization of porous BaTiO3 using impedance spectroscopy in humid condition

The humidity response characteristics of La doped BaTiO₃ with different sintered densities and room temperature electrical conductivities were investigated using complex impedance measurement. The samples with low density and high resistivity showed the large and nearly linear sensitivity to the change of humidity. The impedance spectra of samples, when exposed to high humidity, can exhibit microstructure-related features, even though they do not give rise to a noticeable characteristic change when exposed to low humidity. The observed impedance patterns were dependent upon the density, and hence the oxidation kinetics of BaTiO₃.     

Dielectric barrier discharge treatments at atmospheric pressure for wood surface modification

In this research, the effect of dielectric barrier discharge on mechanically manufactured (sawn, planed or polished) wood surfaces is investigated. The experiments have shown that the best hydrophilia is obtained with a cold plasma discharge in air under atmospheric pressure. Other gases such as helium, nitrogen, and argon have been tested, too. Changes of the wood surface properties were determined by absorption of water and contact angle measurements. As a result of a 1 to 20 seconds long exposure to plasma, wood surfaces became hydrophilic. The absorption of water in wood can be changed up to 22 times higher after plasma treatment in air for 20 seconds duration. The fracture strength of glued wood has been increased by 68% after this plasma pretreatment. Using plasma treatment in methane or acetylene wood surfaces are changed to hydrophobic properties. After plasma treatment for 1 min. in a Ar:CH₄=80:20 gas mixture under atmospheric pressure, the absorption of water in wood is 32 times lower than without plasma treatment. As mentioned before, plasma treatment can produce hydrophobic and hydrophilic wood surfaces. But a good homogeneity of the gas discharge is necessary for the plasma treatment of wood. Zusammenfassung Im Rahmen dieser Arbeit werden die Auswirkungen der dielektrisch behinderten Entladung bei Atmosphärendruck auf mechanisch bearbeitete Holzoberflächen (gesägt, gehobelt oder geschliffen) untersucht. Die Experimente haben gezeigt, dass die höchste Hydrophilität bei einem in Luftatmosphäre gezündetem Plasma erreicht wird. Es werden auch andere Gase verwendet, wie z.B. Helium, Stickstoff und Argon. Zur Untersuchung der veränderten mechanischen und energetischen Eigenschaften der Holzoberflächen werden der Tropfen-Versuch und die Kontaktwinkelmessung verwendet. Durch eine 1 bis 20 Sekunden lange Plasmabehandlung können die Oberflächen hydrophil gestaltet werden. So kann die Eindringzeit von Wasser um Faktor 22 gesteigert werden durch eine 20 Sekunden lange Plasmabehandlung in Umgebungsluft. Die Bruchfestigkeit von Leimholz wird durch die gleiche Plasmavorbehandlung um 68% gesteigert. Werden als Plasmabehandlungsgas Methan oder Acetylen eingesetzt, so wird die Holzoberfläche hydrophob. Durch eine 60 Sekunden lange Plasmabehandlung in einem Ar:CH₄=80:20 Gasgemisch bei Atmosphärendruck wird die Eindringszeit von Wasser um den Faktor 32 gesenkt. Mit Hilfe der Plasmabehandlung können also sowohl hydrophobe als auch hydrophile Holzoberflächen erzeugt werden. Jedoch wird für die Plasmabehandlung von Holz eine sehr homogene Gasentladung benötigt.     

Damage tolerance of glass mat/epoxy laminates hybridized with flexible resin under static and impact loading

This study deals with the impact property and damage tolerance of matrix hybrid composite laminates with different laminate constitution. The matrix hybrid composite laminates consisted of the laminae with a conventional epoxy resin and the laminae with a flexible epoxy resin modified from the conventional resin to avoid the interlaminar delamination. The impact energy absorption ratio greatly depended on the matrix resin placed at the impact face. The energy absorption was almost constant if the conventional resin was placed at the impact surface layer, while it increased exponentially with the increasing fraction of the flexible resin if the flexible resin was placed at the impact face. The impact energy was absorbed by the damage development and propagation in the laminate with conventional resin laminae as the impacted face, while it was absorbed by both the recoverable deformation of the flexible resin and the damage propagation in the laminate with flexible resin laminae as the impacted face.     

U(Ⅳ)-U(Ⅵ)同位素交换反应动力学研究 Ⅰ.Fe~(2+)对U(Ⅳ)-U(Ⅵ)同位素交换反应的催化作用

一、前言由于U(IV)-U(VI)同位素交换体系具有相当大的同位素效应和很好的稳定性,并且容易实现两相回流,这对于分离U同位素的工业应用都是十分有利的。但是,U(IV)-U(VI)同位素交换反应速度非常慢,常温下H~+浓度为1.0—4.0 mol/l时,速度常数为1.0×10~(-4)l~2/mol·s。因此要用U(IV)-U(VI)交换体系浓缩铀同位素,必须研究U(IV)-U(VI)交换反应动力学,找到加快交换反应的方法。     

含氟聚酰亚胺的辐射交联及其交联度的XPS表征

含氟聚酰亚胺(FPI)是一种耐高温、耐水解的新型聚酰亚胺。到目前为止,尚未见文献报道它的辐射交联。本文发现它能在高温辐射下交联,交联后的含氟聚酰亚胺的玻璃化转变温度以及高温力学性能有明显提高。本文还首次用XPS方法做了它的交联度表征。用XPS方法求得FPI的凝胶化剂量为50Mrad。     

A knowledge-based system for sensor selection

This paper presents a Knowledge-based system (KBS) developed to allow users, who may not be knowledgeable about sensors, to select sensors suitable for their specific needs. The KBS runs on a micro-computer. The selection criteria are user specified and are based on the desired measurement parameters. The system output includes all of the operational and dimensional parameters of the recommended sensor, price, and vendor information.