Critical heat flux on a flat plate heater located at the middle of a duct in forced flow of pressurized He II

Critical heat fluxes (CHFs) were measured for two types of rectangular ducts containing horizontal flat plate heaters. One has the flat plate heater of 6 mm wide and 20 mm long located on the inner lower wall at 50 mm from the inlet. The other duct has two horizontal flat plates of 6 mm wide and 20 mm long on inner upper and lower walls at 50 mm from the inlet. The equation of CHF for the forced convection containing a new nondimensional-parameter m introduced in order to calculate cross-sectionally averaged liquid temperature at the center of the duct was derived based on two fluid model, ordinary convection theorem and experimental results. It was confirmed that this correlation can describe not only the author's data on the duct but also other worker's data for channels with different shapes and sizes.     

The Effect of Structural Defects on the Thermal Conductivity of ZnS, ZnSe, and CdTe Polycrystals

ZnS, ZnSe, and CdTe polycrystals are experimentally investigated. Mechanisms are treated which restrict the thermal conductivity in samples prepared by recrystallization pressing and by deposition from the vapor phase and subjected to additional strain. Anomalies are observed on the temperature dependences of the thermal resistance of investigated samples, which are due to the special features of their phonon spectra and to the variation of the contribution made by longitudinal and transverse phonon branches to the heat transfer in the Debye temperature region and higher.     

Filtration of Non-Newtonian Hydrocarbon Fluid in a High-Frequency Electromagnetic Field

The paper gives the results of experimental investigations of the initial pressure gradient of bituminous oil and the time dependences of variation of the temperature in a formation model and of the well production rate in a microwave-frequency electromagnetic field. The effect of strong decay of the non-Newtonian properties of bituminous oil is revealed. The nonuniformity of temperature distribution over the formation thickness is demonstrated, which depends on the initial production rate of the well and on the duration of stimulation of the bottom-hole zone of formation.     

Application of autoregressive spectral analysis to missing data problems

Time series solutions for spectral analysis in missing data problems use reconstruction of the missing data, or a maximum likelihood approach that analyzes only the available measured data. Maximum likelihood estimation yields the most accurate spectra. An approximate maximum likelihood algorithm is presented that uses only previous observations falling in a finite interval to compute the likelihood, instead of all previous observations. The resulting nonlinear estimation algorithm requires no user-provided initial solution, is suited for order selection, and can give very accurate spectra even if less than 10% of the data remains.     

Finite sample properties of ARMA order selection

The cost of order selection is defined as the loss in model quality due to selection. It is the difference between the quality of the best of all available candidate models that have been estimated from a finite sample of N observations and the quality of the model that is actually selected. The order selection criterion itself has an influence on the cost because of the penalty factor for each additionally selected parameter. Also, the number of competitive candidate models for the selection is important. The number of candidates is, of itself, small for the nested and hierarchical autoregressive/moving average (ARMA) models. However, intentionally reducing the number of selection candidates can be beneficial in combined ARMA(p,q) models, where two separate model orders are involved: the AR order p and the MA order q. The selection cost can be diminished by creating a nested sequence of ARMA(r,r-1) models. Moreover, not evaluating every combination (p,q) of the orders considerably reduces the required computation time. The disadvantage may be that the true ARMA(p,q) model is no longer among the nested candidate models. However, in finite samples, this disadvantage is largely compensated for by the reduction in the cost of order selection by considering fewer candidates. Thus, the quality of the selected model remains acceptable with only hierarchically nested ARMA(r,r-1) models as candidates.     

Filtration efficiency and the percolation phenomenon in a grooved-plate Separator

We present here the results of a study of the separation process in the extraction matrix of a novel high-intensity magnetic separator (HIMS). The matrix uses an ordered array of grooved plates (replacing conventional collectors, which are generally made of wires). Only experimental results are available for grooved plates in the literature, but here we propose a new theoretical approach. We report on the particles' behavior, the existence of a percolation phenomenon, and the filtration efficiency, in order to analyze and compare the performance of matrix structures (Lenoir's and Jones'). We discuss the causes of the percolation phenomenon and its effect on filtration efficiency. Correspondence between the theory and the experiments is good. We suggest appropriate uses of each matrix structure according to the property of the processed particles.     

Properties of fine-grained graphites based on two-component fillers

The effect of the nature of two-component fillers on the physical and mechanical properties of finegrained graphites was studied using highly oriented needle coke and nearly isotropic synthetic graphite as components of fillers. Each filler was prepared in the form of coarse (-120 µm) and fine (-10 µm) powders. Different mixtures of these components were used in producing graphite samples, which were then characterized by density, thermal expansion, compressive strength, and modulus of elasticity measurements. The results demonstrate that the thermal expansion, compressive strength, and modulus of elasticity of the graphites thus prepared depend on the microtexture, size, and shape of the filler particles.Translated from Neorganicheskie Materialy, Vol. 40, No. 12, 2004, pp. 1448–1454.Original Russian Text Copyright © 2004 by Samoilov.     

Composition, Structure, and Thermal Expansion of Ca3Fe4S3O6 and CaFeSO

The iron calcium oxysulfides Ca₃Fe₄S₃O₆ and CaFeSO are synthesized by reacting mixtures of CaO and FeS in an inert atmosphere. Their elemental compositions and lattice parameters are determined by x-ray microanalysis and x-ray diffraction. From the temperature-dependent lattice parameters of the oxysulfides (measured up to 1020 K), their thermal expansion coefficients are evaluated.     

Relaxor Behavior of Ge-Doped TlInS2

The dielectric and pyroelectric properties of Ge-doped (0.1 mol %) TlInS₂ crystals are studied. The results demonstrate that TlInS₂ is a ferroelectric relaxor. The experimental data are used to evaluate, using the Vogel–Fulcher relation, the activation energy (0.045 eV), preexponential factor (f ₀ = 2 × 10¹³ Hz), and the dipole-freezing temperature (T _F = 142 K) and to determine the temperature range of the stable relaxor (nanodomain) state and the temperature of the transition to the ferroelectric (macrodomain) state, accompanied by an anomaly in the temperature-dependent pyroelectric coefficient.     

Assessing the Efficiency of Chemical and Mineral Admixtures in Early Cement Hydration

A procedure is proposed for evaluating the efficiency of chemical and mineral admixtures in early cement hydration with the use of calorimetric data and with allowance made for the selective effect of admixtures on the hardening process. The concepts of admixture efficiency and admixture–cement compatibility are formulated and are shown to be of practical importance. The proposed approach is substantiated using thermokinetic results on the effects of various admixtures on the hydration of different cements, and the underlying mechanisms are discussed.