Coriolis effects in the dynamics of a rotating elastic structure

Summary Small oscillations of a rotating elasticum with a mass at the free end are investigated with Poincaré-Lindstedt series. It is shown that the mass moves on a figure-eight shaped curve in a direction determined by the sign of the angular velocity and hence that the Coriolis force influences the motion.     

Process optimization and related material properties of silicon films produced by laser-induced chemical vapour deposition from silane

Laser-induced chemical vapour deposition of silicon films on SiO₂/Si (1 0 0) and Si (1 0 0) substrates was studied using ArF laser irradiation of silane/argon gas mixture in parallel to the substrate. The optimal deposition conditions were specified by examination of film morphology at a wide range of irradiation and process parameters. At optimal conditions, specular films were obtained with no powder formation. The effect of deposition parameters, such as laser energy and repetition rate, on the deposition rate and the related film quality, was investigated.     

Melt-extracted oxide ceramic fibres — the fundamentals

A melt-extraction technique, using a sharpened molybdenum wheel, has been used to produce fine oxide ceramic fibres. Wetting of the molybdenum wheel by molten ceramic is a key parameter in the melt-extraction process. Two types of fibre are generally obtained, depending on the extraction speed. At very low wheel speed, fine and uniform fibres of high quality are produced. However, when the wheel speed exceeds a critical velocity, Rayleigh waves are formed on the free surface of the fibres. Moreover, the average fibre thickness first increases with the wheel velocity, then passes through a maximum, decreasing at high velocity. This thickness variation is discussed in terms of both surface tension and viscosity of the liquid ceramics.     

Effect of type of processing on the microstructural features and mechanical properties of Al-Cu/SiC metal matrix composites

In this study, an aluminum based metallic matrix (Al-2wt.% Cu) was reinforced with SiC particulates using a conventional casting technique and a new disintegrated melt deposition technique. Microstructural characterization studies conducted on the samples taken from disintegrated melt deposition technique revealed a more uniform distribution of SiC particulates and good interfacial integrity between SiC particulates and metallic matrix when compared to the conventionally cast composite samples. Results of ambient temperature mechanical tests demonstrate an increase in 0.2% YS and ultimate tensile strength of samples taken from disintegrated melt deposition technique when compared with the unreinforced and conventionally cast composite samples. The results of microstructural characterization and mechanical testing were finally rationalized in terms of the nature of processing technique employed to reinforce Al-2wt.% Cu metallic matrix with SiC particulates.     

Using internal fibre geometry to improve the performance of pin-loaded holes in composite materials

The anisotropic nature of fibre reinforced composites leads to large stress concentrations around pin-loaded holes through standard weave cloths. Proper understanding of how this anisotropic nature affects the load distribution around holes can be utilised to reduce these concentrations if sufficient thought is given to the internal fibre geometry near to the hole. Such local reinforcements need not be highly complex and can be readily produced without excessive effort, producing significant improvements in performance.     

Studies on the in vitro Release of Ibuprofen from Polyethylene Glycol-Polyvinyl Acetate Mixtures Liquid Filled into Hard Gelatin Capsules

The release of ibuprofen from mixtures of polyethylene glycol (PEG) with polyvinyl acetate (PVAc) has been studied in vitro and complemented by x-ray diffraction measurements, differential scanning calorimetry (DSC), and melting point determinations via hot-stage microscopy (HSM). Results indicate that ibuprofen release can be affected markedly by alteration of the PVAc concentration. The molecular weight of the PEG and the pH of the dissolution medium are also shown to affect the release profile. Visual observation during the drug release process revealed a complex behavior which included emission of liquidlike droplets, formation of a crust around the releasing mass, and/or production of flakes of solid material. This behavior appeared to have a disadvantageous effect on the reproducibility of drug release. Construction of a phase diagram from results of thermal analysis using DSC and HSM indicated the formation of an eutectic mixture with a composition of 35% ibuprofen and 65% PEG 1500 and a melting point of 36°C. The complex behavior of the drug-releasing mass is discussed in terms of this phase diagram. Only the release data for systems containing 4% w/w or more of PVAc could be linearized by plotting against the square root of time whereas data for all of the systems studied could be linearized by first-order plots.     

Adhesion of streptococci to saliva-coated and uncoated composite-based resins

This study was designed to evaluate the bacterial adhesion to five types of experimental composite-based resins and a commercial composite resin used as a control. Physicochemical surface characteristics of composite resins with and without an artificial saliva coating were measured. The relationship between the numbers of adhering cells (Streptococcus sanguis, S. mutans and S. sobrinus) and surface characteristics was analysed. The values of contact angles and the number of adhering cells were small with saliva coating. S. sanguis ATCC 10557 showed a positive correlation (r=0.835, p<0.05) with the contact angles of uncoated resins, whereas no relationship was observed for saliva-coated resins. With S. mutans Ingbritt the cell numbers adhering to resins correlated strongly (p<0.01) with the values of zeta potential of resins for either saliva coated or uncoated. Electrical repulsion forces had a strong contribution to adherence of cells such as S. mutans and S. sobrinus which show a high absolute zeta potential.