Ultrasound as a pre-oxidation for biological landfill leachate treatment.

In this study, the effects of low energy ultrasound irradiation on landfill leachate treatment by means of sequencing bath reactor were investigated. The aim of this work was to estimate the influence of leachate irradiation time on aerobic treatment efficiency. The sonification of the leachate was carried out in static conditions using the disintegrator UD-20. The field frequency of 22 kHz (the power output equals to 180 W) and amplitude of 12 microm was applied. The sonification time was changed in the range of 30-140 s. It was found that ultrasonic pretreatment enhances the subsequent aerobic digestion resulting in a better degradation of landfill leachate. The sonification of raw leachate leads to enhancement of COD and ammonia removal as compare to experiment without ultrasound.     

Multichip Differential Phase-Shift-Keyed Transmission Over (Non)Linear Optical Channels

The recently introduced multichip differential phase-shift keying (MC-DPSK) optical transmission format, entailing the modulation of relative phases over a moving transmission window of successive chip intervals, is analytically and numerically analyzed. The maximum-likelihood optimal MC-DPSK receiver is derived and synthesized using integrated-optic Mach-Zehnder delay interferometers, whose electrical outputs are interpreted as generalized Stokes' parameters. The MC-DPSK performance over a nonlinear fiber channel, limited by the combination of amplified spontaneous emission noise and self-phase modulation, is further derived and simulated, demonstrating that the lowest complexity three-chip binary-phase MC-DPSK receiver provides an ~1-dB Q-factor advantage over conventional DPSK.     

Calorimetric output power measurements on a CW 20 kW 7.16 GHzmicrowave transmitter

A calorimetric measurement technique developed for NASA's Deep Space Network (DSN) transmitters that does not require data on the coolant's thermal parameters is described. Calibration of the measurement system is achieved by measuring the DC input power to the klystron and relating coolant temperature increase to this known power dissipation. Agreement between calorimetric and electrical measurements of total system power was good, the difference being less than 2%. The operation of the system was not greatly affected by the composition of the coolant, which was varied from pure water to 40% ethylene glycol by mass. Good accuracy was also shown at output power levels, which varied over a 3.6:1 range     

Lithium/lithium vanadium oxide secondary batteries: IV. Evaluation of factors affecting the performance of test cells

With the aim of optimizing the performance of Li/Li_1+xV₃O₈ cells, several aspects of cathode preparation have been examined. The influence of synthesis technique, nature and amount of conductive additives, compacting pressure, cathode loading, and particle size, has been investigated. Furthermore, the role played by the solutions on cathode efficiency has been outlined. The formulations which perform best are based on small-sized particles blended with about 20% acetylene black and compacted at very high pressures to improve the contact between particles. Such cathodes can provide high capacities at high rates and good cycling efficiencies. The kinetic loss of capacity, observed during the first few cycles, may be alleviated by choosing solutions with high fluidity and conductivity.     

Evaluation of constructed wetlands by wastewater purification ability and greenhouse gas emissions.

Domestic wastewater is a significant source of nitrogen and phosphorus, which cause lake eutrophication. Among the wastewater treatment technologies, constructed wetlands are a promising low-cost means of treating point and diffuse sources of domestic wastewater in rural areas. However, the sustainable operation of constructed wetland treatment systems depends upon a high rate conversion of organic and nitrogenous loading into their metabolic gaseous end products, such as N2O and CH4. In this study, we examined and compared the performance of three typical types of constructed wetlands: Free Water Surface (FWS), Subsurface Flow (SF) and Vertical Flow (VF) wetlands. Pollutant removal efficiency and N2O and CH4 emissions were assessed as measures of performance. We found that the pollutant removal rates and gas emissions measured in the wetlands exhibited clear seasonal changes, and these changes were closely associated with plant growth. VF wetlands exhibited stable removal of organic pollutants and NH3-N throughout the experiment regardless of season and showed great potential for CH4 adsorption. SF wetlands showed preferable T-N removal performance and a lower risk of greenhouse gas emissions than FWS wetlands. Soil oxidation reduction potential (ORP) analysis revealed that water flow structure and plant growth influenced constructed wetland oxygen transfer, and these variations resulted in seasonal changes of ORP distribution inside wetlands that were accompanied by fluctuations in pollutant removal and greenhouse gas emissions.     

Characterization of Tomato Pulp Stickiness during Spray Drying using a Contact Probe Method

A contact probe test was developed to characterize the surface stickiness of a tomato pulp droplet at various moisture contents and temperatures. To provide tomato pulp samples with different moisture contents, tomato powder produced by a laboratory spray dryer was wetted to seven different moisture levels. The instantaneous tensile force curve was recorded during the probe withdrawal from which the maximum tensile force and other useful information were obtained and cross-examined against images of bonding, debonding, and failure of the material. Generally, at higher moisture contents tomato pulp exhibited cohesive failure followed by semi-adhesive failure, but when moisture content decreased to a certain level, a peak tensile pressure was observed and the failure was adhesive. In addition, higher temperatures shifted the points of adhesive failure toward lower moisture content.