Effects of solvent and temperature on the coupling agent/epoxy resin interface

Increased wetting of the coupling agent/epoxy resin interface was observed when γ-glycidoxypropyltrimethoxysilane, polyfunctional aminosilane and γ-aminopropyltriethoxysilane were applied respectively from methyllethylketone, dimethylformamide and water on woven glass cloths which had been cleaned at 300°C. However, when factory-applied coupling agents were burnt off the woven cloths and fresh coupling agents re-applied, it was found that the nature of the factory-applied coupling agent influenced subsequent wetting. Thinner glass fibres showed a greater improvement in wetting rate than thicker fibres in those solvents identified to be good for improved wettability, irrespective of the heat-cleaning temperature.     

Primary hydration of poly(acrylic acid) sodium salts

Summary The equilibrium water contents of linear poly(acrylic acid) sodium salts with different degrees of neutralisation were found to be dependent on temperature and relative humidity. An octahedral model for the primary hydration of poly(acrylic acid) sodium salts (HIRAOKA and YOKOYAMA 1980) was critically evaluated in the light of these findings and an anomaly in the water uptake versus neutralisation curve at approximately 33% neutralisation was explained by the counterion condensation theory. (MANNING 1979).     

Three ways to implement interfacial techniques: application tomeasurements of chromatic dispersion, birefringence, and nonlinearsusceptibilities

Depending on the spectal width of the source illuminating an interferometer, measurement procedures can utilize either the whole interferogram, or only the fringe envelope, or only the fringe quick oscillations. With an ultraband spectrum source, a simplified adaptation of the methods of Fourier transform spectroscopy yields the variations of the test-fiber propagation constant over the whole wavelength-interval of the source. Chromatic dispersion can then be computed from a single interferogram. With narrower spectrum sources, only the fringe envelopes are utilized and yield measurements of mode delay, with application to chromatic and polarization mode dispersion. In this case, however, interferograms at several wavelengths are necessary. With even narrower spectrum sources, the fringe quick oscillations provide measurements of phase shifts, related to changes in the mode propagation constant, when outside perturbations are applied to the test fiber. A direct method for measuring the third-order nonlinear susceptibilities is discussed. In this case the outside perturbation is an intense pump laser field     

Analytic approach to the computation of the temperature distribution in multilayer structures under heating by cw scanning laser radiation

By using integral transform methods, an approach is developed to the solution of a problem on the temprature distribution in multilayer structures heated by cw scanning laser radiation, with phase transitions in the layers taken into account.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 53, No. 6, pp. 1000–1010, December, 1987.     

A comparison between the axial flux and the radial flux structures for PM synchronous motors

The aim of this paper is the comparison of the axial flux (AF) structures versus the conventional radial flux (RF) structures for permanent-magnet synchronous motors. The comparison procedure is based on simple thermal considerations. Two motor typologies are chosen and compared in terms of delivered electromagnetic torque. The comparison is developed for different motor dimensions and the pole number influence is put into evidence. The paper reports the complete comparison procedure and the related results analysis. The obtained results show that, when the axial length is very short and the pole number is high, the AF motors can be an attractive alternative to the conventional RF solutions.     

Control of free-radical emulsion polymerization of methyl methacrylate by oxygen injection. II. Experimental study

Oxygen injection has been proposed and experimentally demonstrated as an effective control measure for limiting the rate of heat release and altering the rate of polymerization in emulsion processes. A detailed mathematical model has been previously developed to describe the system behavior with and without oxygen injection. A simple lab scale apparatus was constructed and run extensively. Only trace quantities of oxygen are needed to inhibit the reaction completely. The facile response makes this method attractive for fast temperature control. However, because of the rapid penetration of dissolved oxygen into the polymer particles, growing radical chains are terminated prematurely, lowering product molecular weights. To minimize this detrimental effect, pulsed oxygen control is used and extensive experimental work was performed to determine the effects of controller set points on molecular weight. Moderate oxygen flows and moderate set point temperatures are found to give the optimal response without significant lowering of the final molecular weight. Injected quantities agree well with the order-of-magnitude sparging calculations needed to completely stop initiation. However, complete agreement between model simulations and experimental results was not reached due to an unmeasured loss of monomer from the reactor. Chain transfer to monomer is found to be important in modeling the polymer molecular weight. It has, however, a negligible effect on the reaction rate.     

Effects of hydrolysis on the physical properties of short glass-fibre reinforced poly(ethylene terephthalate)

The mechanical fracture strength and toughness of short-fibre composites, injection moulded from compounds of poly(ethylene terephthalate) (PET) containing 10 and 30% (by weight) (w/o) glass, have been investigated and the dependence upon matrix hydrolytic stability determined. Mouldings have been characterised by several physical techniques to evaluate molecular weight, degradation rates, crystallinity and morphology, whilst time-dependent gravimetric data were derived to quantify sorption kinetics and allow comparisons with theoretical reaction rates to be made. During melt processing, PET is hydrolysed extremely rapidly by traces of moisture (<0.02w/o). yet the inherent strength of moulded composites declines significantly only below an apparently critical molecular weight. However, on long-term humid ageing in hot water, impact behaviour especially is rendered more complex by simultaneous crystallisation, molecular reorder and losses of interfacial bond strength.