Analysis of the deformation of polypropylene hot-tool butt welds

Thin microtomed samples from hot-tool butt welds of polypropylene pipes are subjected to uniaxial tensile stress using a specially built instrumented microtesting machine. The deformation of the interface between the weld and the bulk polymer is measured by an optical method. An analysis of these measurements is carried out using the finite element method, and contours of the effective stress are obtained. There is a steep stress gradient at the junction of the weld flash and the bulk polymer, although the stress concentration factor is relatively low. The stress is essentially constant in the bulk polymer apart from the region near the weld zone. Tests on samples without the weld flash show that the maximum stress occurs within the weld zone. This is consistent with long-term tests on larger samples, where the fracture is found to initiate within the weld. The method of analysis enables the stress-strain response of the weld material to be determined.     

Gastrointestinal problems in diabetes

Gastrointestinal symptoms are often encountered in patients with diabetes mellitus. Symptoms may arise in any region of the alimentary tract; common symptoms are heartburn, nausea, vomiting, diarrhea, constipation, fecal incontinence, and abdominal pain. This article reviews practical approaches to the identification of the pathophysiologic mechanisms involved in diabetic enteropathies and their complications and briefly outlines strategies to treat these symptoms. Particular emphasis is placed on applied physiologic tests and the choice of pharmacotherapy (e.g., cisapride, erythromycin, or octeotide). The current role of pancreatic transplantations also is briefly reviewed.     

Drift hole mobility in strained and unstrained doped Si1-xGex alloys

Results of the drift hole mobility in strained and unstrained SiGe alloys are reported for Ge fractions varying from 0 to 30% and doping levels of 10¹⁵-10¹⁹ cm^-3. The mobilities are calculated taking into account acoustic, optical, alloy, and ionized-impurity scattering. The mobilities are then compared with experimental results for a boron doping concentration of 2×10¹⁹ cm^-3. Good agreement between experimental and theoretical values is obtained. The results show an increase in the mobility relative to that of silicon     

Sorption of vapors and gases by cellulose acetate films

Cellulose diacetate and triacetate films 6–55 µm thick with a total porosity of 0.8–2% were prepared by pouring a solution on an immobile surface and by calendering. Sorption of H₂S and CO₂ gases and acetone vapors on these films was investigated in static and dynamic conditions. It was shown that films 6–10 µm thick prepared by calendering should be used for purification of air from H₂S and CO₂ and films 15–20 µm thick prepared by pouring should be used for removal of acetone vapors.Engels Institute of Technology, Saratov State University. Translated from Khimicheskie Volokna, No. 6, pp. 44–46, November–December, 1995.     

Storage performance-metrics and benchmarks

The metrics and benchmarks used in storage performance evaluation are discussed. The technology trends taking place in storage systems, such as disk and tape evolution, disk arrays, and solid-state disks, are highlighted. The current popular I/O benchmarks are then described, reviewed, and run on three systems: a DECstation 5000/200 running the Sprite Operating System, a SPARCstation 1+ running SunOS, and an HP Series 700 (Model 730) running HP-UX. Two approaches to storage benchmarks-LADDIS and a self-scaling benchmark with predicted performance-are also described     

20-nm optical wavelength conversion using nondegenerate four-wavemixing

Wavelength conversion of optical signals over 20 nm is demonstrated using highly nondegenerate four-wave mixing in a semiconductor traveling-wave optical amplifier. This technique has the potential for extremely-high-speed operation and allows continuous tuning of both input and output wavelengths over the amplifier gain bandwidth. It is demonstrated that, even for such a large wavelength conversion range, it is possible to obtain conversion efficiencies in excess of -10 dB and high extinction ratios. The feasibility of the technique is demonstrated by system measurements at 622 Mb/s, showing a 1.1-dB power penalty at 10^-9 bit error rate (BER)