On trading wavelengths with fibers: a cost-performance based study

We consider the effect of multiple fibers on wavelength division multiplexing networks without wavelength conversion. We study networks with dynamic wavelength routing and develop accurate analytical models to compare various possible options using single- and multiple-fiber networks. We use results of an analytical model and simulation-based studies to evaluate the blocking performance and cost of multifiber networks. The number of fibers required providing high performance in multifiber networks and their costs are compared. A case is made for using multiple fibers in each link with fewer wavelengths instead of using a single fiber with many wavelengths. In particular, we show that a network with four fibers per link and with four wavelengths on each fiber without any wavelength conversion on any node yields similar same performance as the networks with one fiber per link and 16 wavelengths per fiber on each link and with full wavelength conversion capability on all nodes. In addition, the multifiber network may also offer the cost advantage depending on the relative cost of components. We develop a parametric cost model to show that multiple fibers in each link are an attractive option. Finally, such multifiber networks also has fault tolerance, with respect to a single fiber failure, already built into the system.     

Nonstationary Simulation Model of Absorber with Falling Film of Suspension

A nonstationary model of SO₂ absorption from a gas phase to a countercurrent falling film of absorbing slurry was developed. Laminar, wavy and turbulent film structures were considered based on published information. Resistances to the mass transfer on the gas and the liquid sides of the interphase were considered, together with chemical reactions in the liquid phase. Relevant chemical equilibria in the liquid phase were modeled. Original experimental data on the neutralization reagent dissolution rate presented as a polydispersed two‐phase system of solids and on the rate of dissolved sulfite oxidation were used. The model was verified with experimental data from a laboratory‐scale falling‐film absorber using a single vertical tube under various geometrical and operating conditions, and a very good agreement was found with the experiment. Parametric sensitivity analysis showed the critical parts of the model.     

Characteristic Features of the Optimal Processing of the Results of Measurements in the Case of a Random Observation Function

An analysis is made of the characteristic features and problems of the optimal processing of the results of measurements in the case of a random observation function utilizing a nonlinear Kalman filter. A method is proposed for increasing the convergence domain of the filter with additional processing of measurements in the frequency domain.     

High-gain hybrid amplifier consisting of cascaded fluoride-based TDFA and silica-based EDFA in 1458-1540 nm wavelength region

A hybrid optical fibre amplifier is described that consists of a fluoride-based thulium-doped fibre amplifier and a silica-based erbium-doped fibre amplifier connected in a cascade. The amplifier has a gain of more than 25 dB and a noise figure of less than 9 dB over a wide wavelength region of 1458-1540 nm.     

An improved statistical analysis of the least mean fourth (LMF) adaptive algorithm

The paper presents an improved statistical analysis of the least mean fourth (LMF) adaptive algorithm behavior for a stationary Gaussian input. The analysis improves previous results in that higher order moments of the weight error vector are not neglected and that it is not restricted to a specific noise distribution. The analysis is based on the independence theory and assumes reasonably slow learning and a large number of adaptive filter coefficients. A new analytical model is derived, which is able to predict the algorithm behavior accurately, both during transient and in steady-state, for small step sizes and long impulse responses. The new model is valid for any zero-mean symmetric noise density function and for any signal-to-noise ratio (SNR). Computer simulations illustrate the accuracy of the new model in predicting the algorithm behavior in several different situations.     

The radiation of a rectangular power-bus structure at multiple cavity-mode resonances

The radiation from power-bus structures on high-speed printed circuit boards due to the switching noise current of digital integrated circuits is investigated. The study is based on an analytical cavity-resonator model for a rectangular parallel-plate structure. Based on the application of the field-equivalence principle, the radiated field is calculated from the electric edge-field distribution. For typical board dimensions, several cavity-mode resonances occur within the typical frequency range of interest, leading to relatively high maximum values for radiated emission. The evaluation of the radiation patterns reveals that all (0, nth) resonances have equal maximum amplitudes in the whole mode spectrum. This allows the setting up of an engineering equation for quantifying the noise-current-related maximum radiated field strength, including the dielectric and ohmic loss. Among all geometrical and material parameters, the dielectric thickness is one of the most effective ones to control radiated emission. The theoretical results are well confirmed by accurate measurements carried out in an anechoic room.     

High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

Failure mode transition and energy dissipation in naturally occurring composites

The microstructural aspects of compressive inelastic deformation in balsa wood are investigated with emphasis on the failure mode transition and its effects on energy dissipation characteristics. The architectural features as well as the composite character of cell wall ultrastructure are discussed in a framework to understand the complex interrelationship between microstructure and macroscopic behavior in this extremely lightweight cellular biocomposite. Based on this discussion and experimental results, it is concluded that the biomimetic approach may prove to be a viable strategy in designing composite structures with high specific energy absorption capacity.