Linearity stablized fiber-optic thermometer using pseudo-heterodyne phase detection

A temperature sensor using a fiber-optic Fabry-Perot interferometer is described. A pseudo-heterodyne detection scheme is adopted to read the light phase difference in the Fabry-Perot interference output. A higher harmonic components comparison method is used to stabilize the system and to increase detection linearity. This system realizes not only highly sensitive temperature sensing with good linearity and minimal adjusting error, but also application to the sensing of other physical quantities such as vibrations. Additionally, the signal-to-noise ratio and distortion of the detected signal are investigated as functions of fiber end reflectivity. These results will be useful in designing a high performance fiber-optic Fabry-Perot thermometer.     

Three-Phase Induction Generator for Single-Phase Line

Hydroelectric generators of less than 20 kilowatts can be in remote areas served only by a single-phase line. For high efficiency and low cost, a three-phase induction generator should be used. This three-phase generator can operate with balanced voltages and currents when the ``phase-splitting' circuit uses two capacitors connetted to two different single-phase voltage sources.     

Convective transfer processes in chemically stable and reacting liquids with an internal structure

Dynamic processes are studied in media with softly and hardly internal destroyable configurations. A method is examined for the measurement of properties of media with spatial separation of the chemical transformation stages and thermal hydrodynamic measurements.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 53, No. 5, pp. 781–789, November, 1987.     

Hydrothermal corrosion of magnesiapartially-stabilized zirconia

Changes in the phase compositions and microstructures of magnesia-partially-stabilized zirconia (Mg-PSZ) were studied in water at 80–300 °C, 1 m HCl solutions at 80–140 °C and 1 m CH₃COOH-CH₃COONa buffer solutions at pH 3 and 80–140 °C for 10–40 days. The tetragonal to monoclinic phase transformation and the degradation of the fracture strength occurred in water above 200 °C. On the other hand, although no noticeable tetragonal to monoclinic phase transformation proceeded in 1 m HCl solutions and 1 m CH₃COOH-CH₃-COONa buffer solutions at pH 3 below 140 °C, the fracture strength of Mg-PSZ greatly degraded. The dissolution of Mg²⁺ ion was observed in water above 200 °C and in 1 m HCl solutions above 80 °C.     

Hot-carrier reliability of 20V MOS transistors in 0.13 μm CMOS technology

This paper presents results of reliability investigation of 20 V N-Drift MOS transistor in 0.13 μm CMOS technology. Due to high performances required for CMOS applications, adding high voltage devices becomes a big challenge to guarantee the reliability criteria. In this context, new reliability approaches are needed. Safe Operating Area are defined for switch, V_ds limited and V_gs limited applications in order to improve circuit designs. For V_ds limited applications, deep doping dose effects in drift area are investigated in correlation to lifetime evaluations based on device parameter shifts under hot carrier stressing. To further determine the amount and locations of hot carriers injections, accurate 2D technological and electrical simulations are performed and permit to select the best compromise between performance and reliability for N-Drift MOS transistor.     

Fabrication of Strain-Relaxed Si<Subscript>1 − <Emphasis Type="Italic">x</Emphasis></Subscript>Ge<Subscript>x</Subscript>/Si(001) Buffer Layers of Low Surface Roughness

The results are presented of the fabrication of strain-relaxed graded Si_{1 − x} Ge_x/Si(001) buffer layers with a maximum Ge fraction of about 0.25 that have a low density of threading dislocations (<10⁶ cm⁻²) and low surface roughness. The buffer layers are grown by atmospheric-pressure hydride CVD. It is found that chemical mechanical polishing can reduce their surface roughness to a level comparable with that of the original Si(001) substrates. It is shown that the polished buffer layers can serve as substrates for MBE-grown SiGe/Si heterostructures.__________Translated from Mikroelektronika, Vol. 34, No. 4, 2005, pp. 243–250.Original Russian Text Copyright © 2005 by Vostokov, Drozdov, Krasil’nik, Kuznetsov, Novikov, Perevoshchikov, Shaleev.     

Autoscan: a scan design without external scan inputs or outputs

We propose a design-for-testability technique for synchronous sequential circuits called autoscan. Autoscan uses scan chains similar to conventional scan. However, it gives up the external scan inputs and outputs in order to eliminate the test data volume associated with them. Scan operations under autoscan improve the circuit testability by allowing the circuit state to be modified through shifting. Due to the removal of the scan inputs and outputs, synthesis of scan chains under autoscan does not have to satisfy all the constraints imposed on conventional scan chains. We describe a synthesis procedure for autoscan chains, and demonstrate that autoscan allows us to detect almost all the faults that are detectable using conventional scan. We use random sequences in order to show that sequential test generation is not necessary under autoscan. We also describe a test generation procedure, and discuss the effect of autoscan on fault diagnosis.     

Force criteria of the state of limiting equilibrium of a cracked plate under biaxial loading

We deduce the theoretical formula taking into account the influence of biaxial loading of a plate weakened by a crack on the stress intensity factor K _I. This enables us to compute the characteristic of crack resistance K _c according to the known boundary forces. __________ Translated from Fizyko-Khimichna Mekhanika Materialiv, Vol. 43, No. 6, pp. 14–16, November–December, 2007.     

Results of testing a centrifugal bubble singlet-oxygen generator

The results of parametric tests of a centrifugal bubble singlet-oxygen generator based on the reaction of chlorine with an alkaline hydrogen peroxide solution have been given. The utilization of chlorine grows with bubble-layer height, whereas the relative content of O₂(¹Δ) remains constant. Growth in centrifugal acceleration leads to a more efficient utilization of chlorine. A specific oxygen output of more than 1 mmole·cm⁻²·sec⁻¹ from the bubble layer for a degree of chlorine utilization of ∼95% and a singlet-oxygen yield of more than 50% has been attained. It has been shown that a centrifugal bubble singlet-oxygen generator is an efficient energy source for an oxygen-iodine laser. __________ Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 80, No. 3, pp. 121–128, May–June, 2007.