Computerized facility layout design

The paper describes a computerized facility layout designer, COMLAD II, for plant layout development. Besides developing an efficient layout, COMLAD II has useful features which allow fixing the departments, changing the shape of the departments and changing the length and width dimensions of the overall layout.     

IBM RISC System/6000: architecture and performance

The IBM RISC System/6000, a superscalar microprocessor, is presented. The architecture of this processor has its instruction set specifically designed for a superscalar machine containing three independent units-branch, fixed-point, and floating-point. The design also emphasizes high-performance floating-point operations. The design principles are to offer maximum overlap of the three functional units, avoid dead cycles, and define instructions that can (for the most part) be completed at a rate of one per cycle. The branch cycle, fixed- and floating-point units, cache management, and performance are described. Benchmark results are given     

Theory of residence-time control by output feedback

The problem of residence-time control by the observer-based output feedback is formulated and solved for the case of linear systems with small additive input noise. Both noiseless and noisy measurements are considered. In the noiseless measurements case, it is shown that the fundamental bounds on the achievable residence time depend on the nonminimum phase zeros of the system. In the noisy measurements case, the achievable residence time is shown to be always bounded, and an estimate of this bound is given. Controller design techniques are presented. The development is based on the asymptotic large deviations theory. Recommended by T K. Caughey     

Surface chemistry and suspension stability of oxide-nitride powder mixtures

The effect of bimetallic oxide sintering aids on the colloidal stability of homogeneous (surface-coated) and heterogeneous (mechanically mixed) silicon nitride powder mixtures in aqueous solution was studied by acoustophoretic analysis. While the surface charge generation and colloidal stability of single-phase and oxide-coated silicon nitride powder mixtures may be described according to the site dissociation model of amine and hydroxyl surface groups, the surface charge observed in heterogeneous multiphase powder mixtures is associated with the adsorption of soluble metal ion hydroxocomplexes on the nitride particles. Segregation of the mixtures by heteroflocculation, which causes the formation of agglomerates and microstructural defects upon sintering, may be avoided by generation of a threshold surface potential of equal sign on all powder constituents at a pH where the metal hydroxide dissolution is subcritical.     

Thermal analysis of the architecture of old and new houses at Ghadames

The study suggests improvements in the design of new houses to conserve energy and enhance indoor thermal comfort. Summer temperature records show that a new house has an average indoor temperature of 35°C with the ambient average 31°C. The traditional house in the old city recorded 28°C for the same period. Winter temperatures in both types of houses were similar (12°C) when not occupied. Architectural features of the two houses were compared to identify those responsible for difference in the thermal performance. Larger exposed surface and window areas, higher overall heat transfer coefficient and weaker thermal coupling with the ground for the new houses seems to contribute to their inferior thermal performance.     

The glass fibre-polymer interface: II—Work of fracture and shear stresses

Pull-out experiments have been carried out on single production fibres under carefully controlled conditions. Four parameters were determined. The interfacial yield stresses, of about 9–14 MPa, were very much smaller than the shear strengths of the bulk polymers in the case of an epoxy, whether post-cured or not, and a non-post-cured polyester. Values for the work of fracture of the interface varied from 140 to 300 Jm^?2, and again were less than those of the polymer. Interface failure sometimes took place in the epoxy rather than at the fibre surface, whereas with the polyester it always took place at the fibre surface. After interface failure, pull-out was governed by friction, with maximum shear stresses of 7–10 MPa for polyester, and 21–34 MPa for epoxy, the higher values being obtained for the post-cured resins. Average frictional shear stresses were sometimes less than a half of the maximum shear stress, indicating that the fibre Poisson's shrinkage was playing an important role in the pull-out process. A silicone release agent reduced the frictional shear stresses to 2·5 MPa, with both resins.     

Location of structural sections from within a highly distorted complex line drawing

Complex and highly distorted line drawings are produced by subjects attempting the Rey Complex Figure test, a clinical test of neuropsychological assessment. However, the marking scheme conventionally employed can be subjective and unreliable. In this paper, the first stages in automating this scoring system are investigated using a robust technique to locate a reduced set of scoring sections and a knowledge-based system that employs spatial metrics and fuzzy approximation techniques. Testing the technique using clinical data produced encouraging results that support the argument that this is a feasible approach for implementing a fully automated system, and that in its current state, can be immediately applied in a semi-automated system.