Ozone measurement in visible region: an optical fibre sensor system

Ozone measurement based on the optical absorption of visible light at 603 nm using polymer optical fibres is investigated and tested. Comparisons with a commercial UV based sensor demonstrate the ability of the visible based sensor to measure high concentrations over a range 27-127 mg/litre. A resolution of 5 mg/litre is also demonstrated for this sensor.     

Performance analysis of information dissemination by flooding

Performance properties are established for the dissemination by flooding of a database that is initially distributed among the nodes of a communications network. An example of this general process is the dissemination of network status information as a component of the adaptive routing mechanism in a network like Arpanet. Bounds are given on the progress of the dissemination process at a sequence of times before the completion of the process, whereas earlier results only bounded the time until completion. The present bounds further extended earlier analysis by treating the diameter explicitly as a parameter. Specialized versions of the bounds are given for k-connected networks. The bounds yield a recognition property whereby a node can recognize that it has received the entire database without having a priori knowledge of the size of the database. An earlier assumption about a fixed time for correct message transmission over any edge is relaxed to assume only an upper bound on these transmission times     

Parametric modeling of somatosensory evoked potentials

In this paper, we examine methods of characterizing somatosensory evoked potentials (SEP's) in both the time and frequency domains. We have found that the truncated impulse response (TIR) method produced an accurate time domain model of the SEP signals at model orders greatly reduced from the original state space matrix. The TIR method was valuable for smoothing signals that were slightly corrupted by noise. In this case, the simulated data sequence was close to the original data sequence in the mean squared error sense. For signals that were greatly corrupted by noise, the TIR method was not able to perform as well. Therefore, the TIR method was not a feature extraction method but was valuable for data simulation. In the frequency domain, we have used the autoregressive moving average model (ARMA) to parameterize the SEP signal. An overdetermined set of Yule-Walker equations was created to determine the autoregressive (AR) parameters of the original data with the model order established by the singular value decomposition. From these AR parameters, a residual time series was generated which was used to find the moving average parameters. The resulting ARMA model was used to produce a simulated data sequence. The frequency domain characteristics of the simulated sequence and the corresponding power spectral density of the ARMA filter were very close to the periodogram of the original data sequence. Accurate parameterization was achieved for the SEP waveforms at low filter lengths.     

Three-Phase Induction Generator for Single-Phase Line

Hydroelectric generators of less than 20 kilowatts can be in remote areas served only by a single-phase line. For high efficiency and low cost, a three-phase induction generator should be used. This three-phase generator can operate with balanced voltages and currents when the ``phase-splitting' circuit uses two capacitors connetted to two different single-phase voltage sources.     

Convective transfer processes in chemically stable and reacting liquids with an internal structure

Dynamic processes are studied in media with softly and hardly internal destroyable configurations. A method is examined for the measurement of properties of media with spatial separation of the chemical transformation stages and thermal hydrodynamic measurements.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 53, No. 5, pp. 781–789, November, 1987.     

Hydrothermal corrosion of magnesiapartially-stabilized zirconia

Changes in the phase compositions and microstructures of magnesia-partially-stabilized zirconia (Mg-PSZ) were studied in water at 80–300 °C, 1 m HCl solutions at 80–140 °C and 1 m CH₃COOH-CH₃COONa buffer solutions at pH 3 and 80–140 °C for 10–40 days. The tetragonal to monoclinic phase transformation and the degradation of the fracture strength occurred in water above 200 °C. On the other hand, although no noticeable tetragonal to monoclinic phase transformation proceeded in 1 m HCl solutions and 1 m CH₃COOH-CH₃-COONa buffer solutions at pH 3 below 140 °C, the fracture strength of Mg-PSZ greatly degraded. The dissolution of Mg²⁺ ion was observed in water above 200 °C and in 1 m HCl solutions above 80 °C.     

Fabrication of Strain-Relaxed Si<Subscript>1 − <Emphasis Type="Italic">x</Emphasis></Subscript>Ge<Subscript>x</Subscript>/Si(001) Buffer Layers of Low Surface Roughness

The results are presented of the fabrication of strain-relaxed graded Si_{1 − x} Ge_x/Si(001) buffer layers with a maximum Ge fraction of about 0.25 that have a low density of threading dislocations (<10⁶ cm⁻²) and low surface roughness. The buffer layers are grown by atmospheric-pressure hydride CVD. It is found that chemical mechanical polishing can reduce their surface roughness to a level comparable with that of the original Si(001) substrates. It is shown that the polished buffer layers can serve as substrates for MBE-grown SiGe/Si heterostructures.__________Translated from Mikroelektronika, Vol. 34, No. 4, 2005, pp. 243–250.Original Russian Text Copyright © 2005 by Vostokov, Drozdov, Krasil’nik, Kuznetsov, Novikov, Perevoshchikov, Shaleev.     

Autoscan: a scan design without external scan inputs or outputs

We propose a design-for-testability technique for synchronous sequential circuits called autoscan. Autoscan uses scan chains similar to conventional scan. However, it gives up the external scan inputs and outputs in order to eliminate the test data volume associated with them. Scan operations under autoscan improve the circuit testability by allowing the circuit state to be modified through shifting. Due to the removal of the scan inputs and outputs, synthesis of scan chains under autoscan does not have to satisfy all the constraints imposed on conventional scan chains. We describe a synthesis procedure for autoscan chains, and demonstrate that autoscan allows us to detect almost all the faults that are detectable using conventional scan. We use random sequences in order to show that sequential test generation is not necessary under autoscan. We also describe a test generation procedure, and discuss the effect of autoscan on fault diagnosis.