Development and adoption of measures for increasing the safety of power-generating units of nuclear power plants with RBMK reactors in 1986–2005

The basic stages and directions of upgrading and reconstruction of the power-generating units of nuclear power plants with RBMK reactors over a period of 20 yr since the Chernobyl accident are reflected in this paper. The greatest amount of work was done in 1986–1990 on all units with RBMK-1000 and-1500 reactors which were operating at that time in the USSR. The purpose of the upgrade was to improve the neutron-physical characteristics of the reactor cores, increase the response speed of the safety and control system and decrease the positive effect of water outflow from the cooling loop of this system, increase the flow capacity of the systems performing emergency discharge of the steam-gas mixture from the reactor, and improve the basic operating documentation. The subsequent stages of the upgrading and reconstruction concerned mainly the first-generation power-generating units (Nos. 1 and 2 units of the Leningrad and Kursk nuclear power plants). These works were performed to make the power-generating units conform to the requirements of the modern normative documents on safety and allow for the possibility of these units to remain in operation after the nominal 30-yr service life has been exhausted. __________ Translated from Atomnaya énergiya, Vol. 100, No. 4, pp. 312–320, April, 2006.     

Redox Equilibrium of Iron in Silicate Glasses

The effect of some additives on the equilibrium of valence forms of iron is investigated. It is demonstrated that tin and carbon more significantly than fluorine reduce iron. The redox potential of the glass matrix affects the equilibrium between difference valence forms of iron much less than additives correcting spectral characteristics of glass.     

Nitrification parameter measurement for plant design: experience and experimental issues with new methods.

Nitrification kinetics are important for process design, optimization, and capacity rating of activated sludge wastewater treatment plants. A Water Environment Research Foundation (WERF) project on Methods for Wastewater Characterization in Activated Sludge Modeling (WERF, 2003) focused significantly on the development of procedures for measuring the nitrifier maximum specific growth rate, micro(AUT). In addition, the importance of (and lack of data for) the nitrifier decay rate, b(AUT), was identified. This paper describes three bench-scale methods for measuring micro(AUT): the Low F/M SBR, Washout and High F/M methods. During the WERF project, the importance of pH and temperature control was investigated briefly; this paper summarizes further experimental work performed to address these issues. A summary of micro(AUT) measurements in a number of locations and using the different measurement techniques is provided.     

Removal of E. coli and helminth eggs in UASB: Polishing pond systems in Brazil.

Ponds following anaerobic reactors, such as Upflow Anaerobic Sludge Blanket (UASB) reactors, have been termed polishing ponds in the literature. The present paper analyses the removal of E. coli and helminth eggs in five UASB-polishing pond systems in Brazil. Since there were ponds in series, the total number of ponds was 10. The ponds had average retention times varying from 2 to 21 days, and depths ranging from 0.40 to 2.00 m. The shallow ponds in series, even with low retention times, were able to produce effluents complying with the coliform WHO guidelines for unrestricted irrigation (< or = 1000 MPN/100 ml). An equation for the coliform decay coefficient was proposed: Kb (dispersed flow) = 0.710H(-0955) (20 degrees C). The equation highlights the inverse relationship between the pond depth and the decay coefficient. All polishing pond systems were able to produce effluents with helminth eggs concentrations predominantly equal to zero, and satisfying the WHO guidelines for unrestricted and restricted irrigation (< or = 1 egg/L, arithmetic mean). The approximate range of helminth eggs removal efficiency was predicted satisfactorily.     

Prediction of Final Product Properties After Cocurrent Spray Drying

The effect of drying and atomization conditions on the physical properties of powders for agglomerate-like materials and skin-forming material are studied in this article. A neural model is used for powder bulk and tapped density predictions.     

Final Drying of Whole Milk Powder in Vibrated-Fluidized Beds

Vibro-fluidized beds are widely used in drying sticky powders and agglomerated materials as milk powder. Using a vibro-fluidized laboratory scale dryer, this work is aiming at analyzing preliminarily the effect of its operational variables on the drying kinetics and characteristics of whole milk powder. The full-factorial design technique with three replications at the central point has been employed to generate data and correlations to quantify the effect of inlet air temperature, air flow rate, and vibration bed amplitude on the drying curves and the milk powder properties related to its faster reconstitution in water (as tapped density, Hausner cohesion ratio, agglomerate size distribution, and internal pore concentration). Results obtained are analyzed and discussed to identify the adequate operation condition for final drying whole milk powder in vibro-fluidized beds, assuring a high product quality.     

Simulation and experimental analyses of electromagnetic transients behaviors of lightning surge on vertical conductors

Simulation of very fast surge phenomena in a three-dimensional (3-D) structure requires a method based on Maxwell's equations, such as the finite-difference time-domain (FDTD) method or the method of moments, because circuit-equation-based methods cannot handle the phenomena. This paper uses a method of thin-wire representation of the vertical conductor system for the FDTD method which is suitable for the 3-D surge simulation. The thin-wire representation is indispensable to simulate electromagnetic surges on wires or steel frames in which the radius is smaller than a discretized space step used in the FDTD simulation. In this paper, a general surge analysis program named the virtual surge test lab based on the Maxwell's equations formulated by the FDTD method, is used to simulate the surge phenomena of a vertical conductor, including the effects of horizontal wave incidence and vertical wave incidence. Experimental results on the reduced scale model have been presented in order to compare among the simulation results by the FDTD method and the results using numerical electromagnetic code based on the MoM.     

The Grey-Rankin bound for nonbinary codes

The Grey-Rankin bound for nonbinary codes is obtained. Examples of codes meeting this bound are given. Original Russian Text Ş L.A. Bassalygo, S.M. Dodunekov, V.A. Zinoviev, T. Helleseth, 2006, published in Problemy Peredachi Informatsii, 2006, Vol. 42, No. 3, pp. 37–44. Supported in part by the Russian Foundation for Basic Research, project no. 06-01-00226.     

Safety assessment of liquid radioactive wastes buried for a long time in deep repositories

The concepts of specific and absolute toxicity permit distinguishing in radioactive wastes belonging to different categories the particular components that present the greatest ecological danger at different stages of their disposal in repositories. It is shown that transuranium elements determine the toxicity parameter of high-and medium-level wastes only 350–400 years after initial disposal. At the present stage of operation of deep repositories, the behavior of the long-lived fission products of ⁹⁰Sr and ¹³⁷Cs is most important. For low-level wastes, the chemical and not the radioactive component is most dangerous. __________ Translated from Atomnaya énergiya,Vol. 100, No. 2, pp. 86–92, February, 2006.