Simulation, modeling, and crystal growth of Cd0.9Zn0.1Te for nuclear spectrometers

High-quality, large (10 cm long and 2.5 cm diameter), nuclear spectrometer grade Cd_0.9Zn_0.1Te (CZT) single crystals have been grown by a controlled vertical Bridgman technique using in-house zone refined precursor materials (Cd, Zn, and Te). A state-of-the-art computer model, multizone adaptive scheme for transport and phase-change processes (MASTRAP), is used to model heat and mass transfer in the Bridgman growth system and to predict the stress distribution in the as-grown CZT crystal and optimize the thermal profile. The model accounts for heat transfer in the multiphase system, convection in the melt, and interface dynamics. The grown semi-insulating (SI) CZT crystals have demonstrated promising results for high-resolution room-temperature radiation detectors due to their high dark resistivity (ρ≈2.8 × 10¹¹ Θ cm), good charge-transport properties [electron and hole mobility-life-time product, μτ_e≈(2–5)×10⁻³ and μτ_h≈(3–5)×10⁻⁵ respectively, and low cost of production. Spectroscopic ellipsometry and optical transmission measurements were carried out on the grown CZT crystals using two-modulator generalized ellipsometry (2-MGE). The refractive index n and extinction coefficient k were determined by mathematically eliminating the ∼3-nm surface roughness layer. Nuclear detection measurements on the single-element CZT detectors with ²⁴¹Am and ¹³⁷Cs clearly detected 59.6 and 662 keV energies with energy resolution (FWHM) of 2.4 keV (4.0%) and 9.2 keV (1.4%), respectively.     

Monolithically Integrated InP 1 $times$ 16 Optical Switch With Wavelength-Insensitive Operation

The static and dynamic characteristics of a monolithically integrated InP 1$,times,$ 16 optical phased-array switch are presented. The device demonstrates static switching with an average extinction ratio of 18.6 dB, on-chip loss below 7 dB, and wavelength dependence of less than 0.8 dB in the entire $C$-band. A 40-Gb/s nonreturn-to-zero signal is transmitted through the switch with a power penalty below 0.4 dB. Using a programmable electronic circuit, dynamic switching to all 16 outputs is achieved with response times less than 11 ns.      

Facile Synthesis of Red/NIR AIE Luminogens with Simple Structures,Bright Emissions,and High Photostabilities,and Their Applications for Specific Imaging of Lipid Droplets and Image‐Guided Photodynamic Therapy

Red/near‐infrared (NIR) fluorescent molecules with aggregation‐induced emission (AIE) characteristics are of great interest in bioimaging and therapeutic applications. However, their complicated synthetic approaches remain the major barrier to implementing these applications. Herein, a one‐pot synthetic strategy to prepare a series of red/NIR‐emissive AIE luminogens (AIEgens) by fine‐tuning their molecular structures and substituents is reported. The obtained AIEgens possess simple structures, good solubilities, large Stokes shifts, and bright emissions, which enable their applications toward in vitro and in vivo imaging without any pre‐encapsulation or ‐modification steps. Excellent targeting specificities to lipid droplets (LDs), remarkable photostabilities, high brightness, and low working concentrations in cell imaging application make them remarkably impressive and superior to commercially available LD‐specific dyes. Interestingly, these AIEgens can efficiently generate reactive oxygen species upon visible light irradiation, endowing their effective application for photodynamic ablation of cancer cells. This study, thus, not only demonstrates a facile synthesis of red/NIR AIEgens for dual applications in simultaneous imaging and therapy, but also offers an ideal architecture for the construction of AIEgens with long emission wavelengths.     

用于电源、继电器和螺线管的协同式线路保护

在各种新型先进设备上实施协同式电路保护可有助于提高设备可靠性、减少元器件数量,并使其符合严格的安规要求。协同式方法能够帮助保护电源、继电器和螺线管,避免因线路故障或过载造成电流增大以及尖峰电压或暴露在稳态过压状态带来的危害。     

Detecting Low-Power RF Signals Using a Multimode Optoelectronic Oscillator and Integrated Optical Filter

We have assembled and characterized a multimode optoelectronic oscillator with integrated optical filter for detecting low-power radio-frequency (RF) signals. The system can selectively amplify RF signals from 1 to 6 GHz. The input signals can be as low as $-$ 83 dBm with a compression dynamic range of 72 dB. Using an integrated silicon optical filter facilitates channelization of the amplified RF signal from 1 to 3 GHz by reducing the gain for signals above 3 GHz. Future system improvements are discussed.      

Performance Analysis of Integrated Voice and Data Hybrid-Switched Links

Numerical techniques for the solution of a class of twodimensional Markov processes are presented. These techniques are used to analyze the performance of several versions of hybrid switching including the movable boundary scheme with finite or infinite buffers, with flow control, and with or without TASI. Also included are results for TASI in which the number of off-hook calls is not fixed. Finally, the accuracy of the quasi-static approximation is evaluated for several problems.     

An autonomous controller for improved dynamic performance of parallel-connected,single-phase inverters

A new control technique is presented for the parallel connection of distributed generation inverters. The proposed control technique is based on a modification of the power angle droop control method, and uses only locally measured feedback signals. An improvement in transient response is achieved because the real and imaginary components of the output current are used when deriving the power angle droop controller. The method achieves good active and reactive power sharing and minimises circulating current between parallel connected units. Improved transient response is obtained whilst maintaining power sharing precision or output voltage and frequency accuracy. Simulation and experimental results validate that performance is better than that attained with conventional droop-based approaches.     

Wide-band Fabry-Perot-like filters in optical fiber

We report the fabrication and characterization of wide-band Fabry-Perot-like resonators in optical fiber. Using Bragg gratings with variable detuning, resonators that operate ever a wavelength span in excess of 140 nm have been produced, with free spectral ranges between 0.09 nm and 11.27 nm. Numerical and experimental results for two typical resonators are presented, showing good agreement between the two     

Chromophore-Free Sealing and Repair of Soft Tissues Using Mid-Infrared Light-Activated Biosealants

Poor strength, infection, leakage, long procedure times, and inflammation limit the efficacy of common tissue sealing devices in surgeries and trauma. Light-activated sealing is attractive for tissue sealing and repair, and can be facilitated by the generation of local heat following absorption of nonionizing laser energy by chromophores. Here, the inherent ability of biomaterials is exploited to absorb nonionizing, mid-infrared (midIR) light in order to engender rapid photothermal sealing and repair of soft tissue wounds. In this approach, the biomaterial simultaneously acts as a photothermal convertor as well as a biosealant, which dispenses the need for exogeneous light-absorbing nanoparticles or dyes. Biomechanical recovery, mathematical modeling, histopathology analyses, tissue strain mapping using digital imaging correlation, and visualization of the biosealant-tissue interface using hyperspectral imaging indicate superior performance of midIR sealing in live mice compared to conventional sutures and glue. The midIR-biosealant approach demonstrates rapid sealing of soft tissues, improves cosmesis, lowers potential for scarring, obviates safety concerns because of the nonionizing light used, and allows adoption of a wide diversity of biomaterials. Taken together, the studies demonstrate a novel advance both in biomaterials for surgical sealing along with the use of nonionizing midIR light, with high potential for clinical translation.     

Modeling ion implantation of HgCdTe

Ion implantation of boron is used to create n on p photodiodes in vacancy-doped mercury cadmium telluride (MC.T). The junction is formed by Hg interstitials from the implant damage region diffusing into the MC.T and annihilating Hg vacancies. The resultant doping profile is n⁺/n^-/p, where the n⁺ region is near the surface and roughly coincides with the implant damage, the n^- region is where Hg vacancies have been annihilated revealing a residual grown-in donor, and the p region remains doped by Hg vacancy double acceptors. We have recently developed a new process modeling tool for simulating junction formation in MC.T by ion implantation. The interstitial source in the damage region is represented by stored interstitials whose distribution depends on the implant dose. These interstitials are released into the bulk at a constant, user defined rate. Once released, they diffuse away from the damage region and annihilate any Hg vacancies they encounter. In this paper, we present results of simulations using this tool and show how it can be used to quantitatively analyze the effects of variations in processing conditions, including implant dose, annealing temperature, and doping background.