Mechanisms of Hf dopant incorporation during the early stage of chemical vapor deposition aluminide coating growth under continuous doping conditions

A laboratory-scale chemical vapor deposition (CVD) reactor was used to perform “continuous” Hf doping experiments while the surface of a single-crystal Ni alloy was being aluminized to form an aluminide (β-NiAl) coating matrix for 45 minutes at 1150 °C. The continuous doping procedure, in which HfCl₄ and AlCl₃ were simultaneously introduced with H₂, required a high HfCl₄/AlCl₃ ratio (>∼0.6) to cause the precipitation of Hf-rich particles (∼0.1 μm) at grain boundaries of the coating layer, with the overall Hf concentration of ∼0.05 to 0.25 wt pct measured in the coating layer by glow-discharge mass spectroscopy (GDMS). Below this ratio, Hf did not incorporate as a dopant into the growing coating layer from the gas phase, as the coating matrix appeared to be “saturated” with other refractory elements partitioned from the alloy substrate. In comparison, the Hf concentration in the aluminide coating layer formed on pure Ni was in the range of ∼0.1 wt pct, which was close to the solubility of Hf estimated for bulk NiAl. Interestingly, the segregation of Hf and the formation of a thin γ′-Ni₃Al layer (∼0.5 μm) at the coating surface were consistently observed for both the alloy and pure-Ni substrates. The formation of the thin γ′-Ni₃Al layer was attributed to an increase in the elastic strain of the β-NiAl phase, associated with the segregation of Hf as well as other refractory alloying elements at the coating surface. This phenomenon also implied that the coating layer was actually growing at the interface between the γ′-Ni₃Al layer and the β-NiAl coating matrix, not at the gas/coating interface, during the early stage of the coating growth.     

Correlation of damage, dry band arcing energy, and temperature in inclined plane testing of silicone rubber for outdoor insulation

Silicone rubber samples, filled with 30% alumina trihydrate, subjected to the ASTM inclined plane test, show good correlation between the measured harmonic power components of dry band arcing and the surface temperature recorded with a thermovision camera. The simultaneous study of the low frequency fast Fourier transform and variations in temperature shows that when the temperature rises above 100/spl deg/C there is a well defined increase in the low frequency harmonic components of the measured power; however, this trend is not verified by the fundamental component. The eroded mass of the samples is measured independently by a laser approach and a model to rank the tested samples using the inclined plane test is developed. The model is validated by applying it to both the recorded harmonic power components and temperature, resulting in the correct ranking of damage on the samples tested in the inclined plane test.     

VLDL receptor mediates the uptake of human chylomicron remnants in vitro

The VLDL receptor has been described as a new member of the LDL receptor supergene family that specifically binds VLDL in vitro via apolipoprotein E and lipoprotein lipase. Both apolipoprotein E and lipoprotein lipase are constituents of chylomicron remnants, another triglyceride-rich lipoprotein which has been proposed as a physiological ligand for the VLDL receptor. We used human chylomicron remnants to study their uptake into LDL, receptor-deficient Chinese hamster ovary cells overexpressing the human VLDL receptor. The uptake into these cells was compared to that into cells transfected with an empty transfection vector. Human chylomicron remnants were produced in vitro by hydrolysis with lipoprotein lipase, and were labeled with 125I. The uptake of these remnants into the cells overexpressing the VLDL receptor was found to be about 3-fold higher than the uptake into the control cells. The addition of a surplus of either apolipoprotein E or inactivated lipoprotein lipase to the remnants led to an increase in particle uptake. The chylomicron remnant uptake was inhibited by addition of the 39 kDa receptor associated protein These in vitro experiments strongly support the idea that the VLDL receptor is a physiological receptor for chylomicron remnants. The increase of receptor-mediated uptake induced by the addition of apoE or lipoprotein lipase underlines the role of these two proteins in this process.     

Structural interaction of natural and synthetic inhibitors with the venom metalloproteinase, atrolysin C (form d)

The structure of the metalloproteinase and hemorrhagic toxin atrolysin C form d (EC 3.4.24.42), from the venom of the western diamondback rattlesnake Crotalus atrox, has been determined to atomic resolution by x-ray crystallographic methods. This study illuminates the nature of inhibitor binding with natural (< Glu-Asn-Trp, where < Glu is pyroglutamic acid) and synthetic (SCH 47890) ligands. The primary specificity pocket is exceptionally deep; the nature of inhibitor and productive substrate binding is discussed. Insights gained from the study of these complexes facilitate the design of potential drugs to treat diseases where matrix metalloproteinases have been implicated, e.g., arthritis and tumor metastasis.     

Determination of Intra- and Extracellular Metabolic Adaptations of 3D Cell Cultures upon Challenges in Real-Time by NMR

NMR flow devices provide longitudinal real-time quantitative metabolome characterisation of living cells. However, discrimination of intra- and extracellular contributions to the spectra represents a major challenge in metabolomic NMR studies. The present NMR study demonstrates the possibility to quantitatively measure both metabolic intracellular fingerprints and extracellular footprints on human control fibroblasts by using a commercially available flow tube system with a standard 5 mm NMR probe. We performed a comprehensive 3D cell culture system characterisation. Diffusion NMR was employed for intra- and extracellular metabolites separation. In addition, complementary extracellular footprints were determined. The implemented perfused NMR bioreactor system allowed the determination of 35 metabolites and intra- and extracellular separation of 19 metabolites based on diffusion rate differences. We show the reliability and sensitivity of NMR diffusion measurements to detect metabolite concentration changes in both intra- and extracellular compartments during perfusion with different selective culture media, and upon complex I inhibition with rotenone. We also demonstrate the sensitivity of extracellular footprints to determine metabolic variations at different flow rates. The current method is of potential use for the metabolomic characterisation of defect fibroblasts and for improving physiological comprehension.     

Cloning and Functional Characterization of Dog OCT1 and OCT2: Another Step in Exploring Species Differences in Organic Cation Transporters

OCT1 and OCT2 are polyspecific membrane transporters that are involved in hepatic and renal drug clearance in humans and mice. In this study, we cloned dog OCT1 and OCT2 and compared their function to the human and mouse orthologs. We used liver and kidney RNA to clone dog OCT1 and OCT2. The cloned and the publicly available RNA-Seq sequences differed from the annotated exon-intron structure of OCT1 in the dog genome CanFam3.1. An additional exon between exons 2 and 3 was identified and confirmed by sequencing in six additional dog breeds. Next, dog OCT1 and OCT2 were stably overexpressed in HEK293 cells and the transport kinetics of five drugs were analyzed. We observed strong differences in the transport kinetics between dog and human orthologs. Dog OCT1 transported fenoterol with 12.9-fold higher capacity but 14.3-fold lower affinity (higher K_M) than human OCT1. Human OCT1 transported ipratropium with 5.2-fold higher capacity but 8.4-fold lower affinity than dog OCT1. Compared to human OCT2, dog OCT2 showed 10-fold lower transport of fenoterol and butylscopolamine. In conclusion, the functional characterization of dog OCT1 and OCT2 reported here may have implications when using dogs as pre-clinical models as well as for drug therapy in dogs.     

High-temperature performance of InGaAs-InGaAlAs-InP 1.79-μmdiode lasers grown in solid-source molecular-beam epitaxy

1.79-μm InGaAs-InGaAlAs strained-layer quantum-well diode lasers have been fabricated. A characteristic temperature of 72 K has been achieved. At a temperature as high as 100°C, a continuous-wave output power of more than 6.5 mW per facet has been demonstrated with lasers using as-cleaved facets as mirrors