Synthesis and characterization of maltose fatty acid monoesters as biosurfactants

Maltose long-chain fatty acid esters (MFAE), esterified at the 6 and 6′ position, were synthesized with stearic, palmitic, myristic, and oleic groups. Synthesis yields were 15–20% based on initial maltose present, and structural confirmation was obtained using plasma desorption mass spectrometry and nuclear magnetic resonance spectroscopy. These surfactants have surface tensions in the range of 34–36 dyn/cm at their critical micelle concentrations (CMC) of approximately 10⁻⁵–10⁻⁶ mol/L. The increased chain lengths have a marked effect, reducing CMC values for MFAE by approximately three orders of magnitude over similar carbohydrate-based dodecyl chain sources. Within chain lengths between 14 and 18 carbons, the rate of change in CMC is significant and decreases with increasing chain length for MFAE. The melting points of MFAE are approximately 40°C, and the heat capacities range from 1.6 to 1.9 J/g·K. These numbers are comparable to those of sucrose esters, indicating their applicability in similar uses. However, because MFAE, unlike sucrose, possess an anomeric carbohydrate carbon position, these surfactants maintain their reducing nature and are susceptible to further derivatization. They are also synthesized from renewable, economical carbohydrates and lipids and may provide an excellent alternative to pertrochemical-derived products.     

The prediction of transport parameters in filamentous fermentation broths based on results obtained in pseudoplastic polymer solutions

Transport phenomena studies on single phase “model” fluids are of limited value in biochemical engineering if they cannot be translated to the heterogeneous systems encountered in real fermentation processes. In this paper we discuss the utility of polymer solutions as models of filamentous fermentation broths for evaluation of: pipeline friction factors and impeller power numbers (turbine and helical ribbon). To a first approximation, polymer solutions can serve as suitable models for the prediction of laminar flow pressure drop in pipelines and turbulent power consumption in stirred tanks. However, results obtained on polymer solutions do not directly apply to filamentous fermentation broths for predictions of laminar flow impeller power consumption and the transition point for turbulent flow in stirred tanks. These discrepancies are believed to result from the existence of a time dependent yield stress in filamentous fermentation broths.     

Characterization of Ceramics by X-Ray and Neutron Small-Angle Scattering

This paper reviews some recent advances in small-angle X-ray and neutron scattering methods and their application to address complex issues in ceramic systems of technological importance. It is shown how small-angle scattering (SAS) can be applied to ceramic systems in order to extract statistically representative microstructure information (e.g., void volume fraction size distributions, internal surface areas, pore morphologies) that complements the information obtained from diffraction methods, X-ray microtomography, or electron microscopy. It is demonstrated how SAS studies provide insights, not obtainable by other means, on the processing–microstructure–property relationships that frequently govern technological performance.     

Thermomechanical heat of deformation studies on cis-polybutadiene

Thermomechanical heat of torsional deformation measurements have been made on crosslinked cis-polybutadiene by means of a Calvet microcalorimeter operated at 30°C. When corrected for volume changes utilizing the Gaussian statistical theory of elasticity, the data gave a value for the relative energy contribution to the torsional couple, $\text{M}{}_{\mathrm{e}}\text{M}$, of 0.14 ± 0.02. Measurements were also made on a sample subjected to simple tensile deformations. The relative energy contribution to the tensile force ($\text{f}{}_{\mathrm{e}}\text{f}$) was found to agree within experimental error with the value obtained for $\text{M}{}_{\mathrm{e}}\text{M}$, and the two results gave an average value for din $\text{〈r}{}^2{}_0\text{〉}\text{d}\text{T}$ of 4.1 × 10^?4 K^?1.     

Preparation and Characterization of 17O-Enriched Alumina for Nuclear Fusion Damage Experiments

Alumina enriched in ¹⁷O was successfully fabricated from aluminum isopropoxide and water containing the ¹⁷O isotope. This material was necessary for an experiment to study the radiation damage expected in alumina exposed to a nuclear fusion reactor environment. The enrichment levels of specimens subjected to different preparation schedules were measured using a nuclear reaction analysis technique. Replacement of the ¹⁷O isotope in the ceramic by atmospheric oxygen occurred readily. Therefore, successful fabrication of suitably enriched alumina specimens required that all processing steps be performed under vacuum or inertgas environments. The optimum fabrication procedure produced enriched alumina specimens of >99.5% of theoretical density, ∽10-μm grain size, and a flexural strength of 280 MPa.     

Surface Preparation of Tantalum for Encapsulation and Adhesive Bonding

A number of methods of surface preparation of tantalum for encapsulation in silicone rubber and for structural adhesive bonding were explored. The only ones which could be generally useful were boiling for 24 hours in distilled water (28% improvement) or boiling for 4 hours in 20% sodium hydroxide solution followed by boiling for 2 hours in dilute hydrochloric acid (34% improvement). An alternative, which could sometimes be used, was heating in air for at least 2 hours at 100°C.     

Effects of experimental endogenous hyperlipemia on circulating leukocytes and erythrocytes

Effects of hyperlipemia on circulating leukocytes and erythrocytes were studied in dogs which were given repeated, intravenous injections of a nonionic detergent, Triton WR-1339. Erythrocyte lipid concentrations increased from 3.6±0.9 mg/10¹⁰ cells in control animals to 9.3±1.5 mg in the hyperlipemic group. This increase was accompanied by a shift in the distribution of total fatty acids toward a higher percentage of saturated and monounsaturated acids. In contrast to the changes observed in erythrocytes, the leukocyte lipid content remained unaltered in dogs with serum cholesterol levels ranging from 500 to more than 2,000 mg/100 ml. Leukocyte counts rose whereas hematocrit values, hemoglobin concentrations, and erythrocyte counts decreased. Oxygen utilization studies showed no significant metabolic differences between leukocytes which were isolated from hyperlipemic or control animals. Circulating leukocytes in dogs with an endogenously induced hyperlipemia were shown therefore to maintain normal lipid concentrations and did not participate in lipophage formation, as reported for certain diet-induced lipemias.     

Water uptake and tensile properties of carboxylated styrene butadiene rubber based water born paints: Models for water uptake prediction

Despite significant advances in water based surface coating technology, the presence of surfactants in emulsion polymer binders leads to loss of performance after prolonged immersion in water, relative to solvent based coatings that are free of surfactant impurities. This study begins with water uptake evaluation of a range of emulsion polymer binders. A carboxylated styrene butadiene rubber latex (c-SBR) performed best in the latter evaluations and was selected for the formulation of an exterior grade paint and construction of a mathematical model to predict water uptake of the dry film. The c-SBR was then compounded with a range of inorganic fillers and water uptake and tensile properties were evaluated. Talc was found to be the best performing filler, and was used in a three factorial central composite design study where the simultaneous effects of talc, titanium dioxide and phenolic stabiliser on water up take were evaluated and fitted to response equations. A quadratic model was found to provide the most accurate prediction of effects associated with interactions between talc and TiO₂. Certain combinations of talc and titanium dioxide were found to be synergistic in reducing the water uptake. This was considered to be associated with a packing effect stemming from the vast difference in particle size between talc and titanium dioxide particles. An optimised formulation was finally prepared to meet one of the final formulation objectives; i.e., minimised water uptake. Preparation of such a formulation showed that the predicted and measured water uptake responses were in excellent agreement. This study illustrates the effectiveness of statistical experimental design methods in predicting the water uptake characteristics of water-based coatings.     

Note: The Use of Triallyl Cyanurate in Bonding PVC Plastisols to Steel

The use of diallyl phthalate as the basis for a non-extractable plasticizer for poly(vinylchloride) (PVC) is well-known. Used in conjunction with a primary plasticizer and a polymerization initiator, a plastisol coating for steel can be formulated which is oil or grease tolerant and can also be used for bonding some structural steel parts if the area is relatively large compared with the load to be applied. Defrayne and Twiss¹ describe the bonding of automobile hood assemblies by vinyl plastisol adhesives and Schneberger² emphasizes their use in the automobile industry though neither article gives the formulations employed. Commercial formulations giving pull-off strengths of the order of 1 to 4 MN. m^-2 always incorporate a proportion of a phenolformaldehyde resin or even an epoxy, but sound-deadening and other coatings of steel do not necessarily need this reinforcement. Phillips and Longworth³ particularly studied the use of diallylphthalate (DAP) as a polymerizable plasticizer and the consequent improvement in adhesion to mild steel. Sherlock⁴ used a simple formulation without additives when investigating the effect of surface cleaning and conversion coatings (oxides and phosphates). It was suggested that, as outlined below, improved adhesion would be expected if a small proportion of triallyl cyanurate (TAC) were added to the polymerizable plasticizer. This paper shows this expectation to be achieved although the proportion of the more expensive TAC needed for substantial increase in bond strength is greater than was hoped.     

A two‐station embossing process for rapid fabrication of surface microstructures on thermoplastic polymers

An embossing strategy involving a hot station and a cold station for sequentially heating and cooling the embossing tool was investigated to reduce cycle times in hot embossing polymer microstructures. Experimental studies showed that aluminum stamps with a thickness of 1.4 mm can be rapidly heated from room temperature to 200°C in 3 s using contact heating against a hot station at 250°C. Microchannels and microlenses were successfully embossed onto high‐density polyethylene and acrylonitrile–butadiene–styrene substrates using a heating time less than 3 s and a total cycle time around 10 s. The two‐station embossing process for the microlens was also numerically studied. The simulated filling behavior agreed with the experimental observation and the predicted thermal and deformation history of the polymer offered a good explanation on the experimentally observed process characteristics. POLYM. ENG. SCI., 47:530–539, 2007. © 2007 Society of Plastics Engineers.