Waste-to-energy: A way from renewable energy sources to sustainable development

Nowadays, energy is key consideration in discussions of sustainable development. So, sustainable development requires a sustainable supply of clean and affordable renewable energy sources that do not cause negative societal impacts. Energy sources such as solar radiation, the winds, waves and tides are generally considered renewable and, therefore, sustainable over the relatively long term. Wastes and biomass fuels are usually viewed as sustainable energy sources. Wastes are convertible to useful energy forms like hydrogen (biohydrogen), biogas, bioalcohol, etc., through waste-to-energy technologies.In this article, possible future energy utilization patterns and related environmental impacts, potential solutions to current environmental problems and renewable energy technologies and their relation to sustainable development are discussed with great emphasis on waste-to-energy routes (WTERs).     

Frequency dependent electrical transport properties of 4,4′,4″-tris(N-3-methylphenyl-N-phenylamine)triphenylamine by impedance spectroscopy

The frequency dependent ac conduction mechanism in 4,4′,4″-tris(N-3-methylphenyl-N-phenylamine)triphenylamine (m-MTDATA) has been studied as a function of applied bias and temperature. The Cole–Cole plot shows a slightly depressed semicircle indicating Debye type relaxation. This result has been explained by an equivalent circuit of the device designed as a two parallel resistor and capacitance network in series with contact resistance. The ac conduction studies under dc bias for hole only devices shows an increase in device conductivity with the increase in bias. The variation of bulk resistance with applied bias indicates Space Charge Limited Conduction (SCLC) mechanism for hole conduction. The hole mobility of the material has also been evaluated from SCLC as 8.859 × 10^?6 cm²/V s. The temperature dependent impedance studies show two activation energies indicating two different phase of the material with a phase transition at 235 K.     

Evidence of low-symmetry phases in pressure-dependent Raman spectroscopic study of BaTiO<Subscript>3</Subscript>

In the earlier pressure-dependent Raman spectroscopic studies, it has been reported that BaTiO₃ undergoes a tetragonal to cubic phase transition above ~ 2 GPa, whereas pressure-dependent X-ray absorption, X-ray diffuse scattering studies and pair distribution function studies have reported the presence of a low-symmetry rhombohedral phase above ~ 2.3 GPa. In this report, we present our pressure-dependent Raman spectroscopic studies on polycrystalline BaTiO₃ which shows that it first undergoes a transition from tetragonal to orthorhombic/rhombohedral phase above ~ 2.6 GPa and then finally goes to the cubic phase above 8.4 GPa. Pressure-dependent synchrotron X-ray diffraction (SXRD) studies have also been carried out that provided rate of change of volume as a function of pressure resulting in bulk modulus of 215 ± 9 GPa.     

Geometric optimization of trapezoidal thermoelectric heat pump considering contact resistances through genetic algorithm

An alternate option for improving the performance of the thermoelectric heat pump (TEHP) is the variation in thermoelectric leg configuration. In this paper, the thermodynamic model based on first and second law of thermodynamics for an exoreversible TEHP including influence of Thomson effect as well as leg geometry on the coefficient of performance and heating load of the device has been developed and optimized. Modified expressions have been derived analytically for dimensionless heating load, irreversibilities, figure of merit, energy, and exergy efficiency. The effects of operating and geometry parameters such as shape parameter (A_c/A_h), temperature ratio (T_c/T_h), Thomson effect, thermal and electrical contact resistances on the coefficient of performance, and heating load of the TEHP have been analysed. The results indicate that the Thomson effect has adverse effect on heating load of the system. The optimal parameters obtained through GA optimization process have been compared with the optimal parameters obtained through analytical method which proved the validity of GA optimization method for optimization of TEHP. After the testing, the GA optimization has been performed to determine the optimum parameters corresponding to maximum energy efficiency and maximum heating load. It was found that the GA population converges quickly after 20 runs only which proved the GA as time and cost‐effective optimization tool. This study will be useful for designing of practical TEHP systems of different leg geometries.     

Studies on the production of B. thuringiensis based biopesticides using wastewater sludge as a raw material

Growth and delta-endotoxin yield of Bacillus thuringiensis (Bt) subsp kurstaki in tryptic soy yeast extract (TSY) medium, soybean meal based commercial medium and wastewater sludge medium were studied. The viable spores (VS) count in sludge medium was comparable to that obtained in laboratory and commercial media. The entomotoxicity of the fermentation liquid (Bt grown sludge) against Choristoneura fumiferana was comparable to the concentrated commercial Bt formulation available in the market (Foray 48B). A higher entomotoxicity was observed in a sludge medium than in the TSY or soybean meal media. The secondary and mixed (mixture of primary and secondary) sludges from various wastewater treatment plants were also evaluated for spore formation and entomotoxicity yield. The VS count was higher in a mixed sludge compared to the secondary sludge at a similar sludge solids concentration. Both VS count and entomotoxicity yield was found to be a function of sludge solids concentration in the medium. The optimum value of solids concentration for Bt production was found to be 25 g (-1) (dry weight basis). Beyond this concentration, a drop in VS count and entomotoxicity yield was observed. A low C:N ratio in the secondary sludge and a high C:N ratio in the mixed sludge resulted in a higher entomotoxicity. The optimum value of C:N ratio in combined sludge for Bt production was found to be 7.9-9.9. Relationships between entomotoxicity and maximum specific growth as well as with specific sporulation rate were developed.     

Preparation, thermal expansion, high pressure and high temperature behavior of Al2(WO4)3

The titled compound Al₂(WO₄)₃ was synthesized by a conventional solid state reaction and characterized by powder XRD. It crystallizes in an orthorhombic (Pbcn, No. 60) lattice, with unit cell parameters as 12.582(2), 9.051(1), 9.128(2) Å, and V = 1039.5(3) (Å)³. The compound was found to show negative thermal expansion (NTE) behavior in the temperature range of 25 to 850°C. The average linear NTE coefficient (₁), in this temperature range, was –1.5 × 10^–6 K^–1. The effect of pressure at ambient temperature, was studied by a Bridgman Anvil (BA) apparatus, to reveal that there is no irreversible phase transition up to 8 GPa. The effect of high pressure and high temperature on this compound was studied by a Toroid Anvil (TA) apparatus. This compound has a limited stability under high pressure and temperature, as it undergoes a decomposition to AlWO₄ and WO_3–x with a partial oxygen loss. As an off-shoot of this work, certain new modifications of WO_3–x under pressure and temperature were observed, viz., monoclinic, tetragonal and an orthorhombic modifications at 5 GPa/1400°C, 3 GPa/900°C and 1.8 GPa/1030°C, respectively. The detailed XRD studies of the products are presented here.