Removal of Cr(VI) and As(V) from aqueous solutions by HDTMA-modified zeolite Y

The synthesized zeolite NaY from rice husk ash (RHA) and the commercial zeolite NaY both modified with surfactants in amounts equal to 50%, 100% and 200% of their external cation exchange capacity (ECEC) were used to remove chromate and arsenate anions from aqueous solutions. While the unmodified zeolite Y had little or no affinity for the Cr(VI) and As(V) anionic species, the surfactant-modified zeolite Y (SMZY) showed significant ability to remove of these anions from the aqueous solutions. The highest chromates and arsenates adsorption efficiency was observed from solutions of pH values 3 and 8, respectively because of the dominance of the univalent species of both anions. The adsorption equilibrium data were best fitted with the Langmuir isotherm model with the highest removal capacities observed for the SMZY initially prepared considering the hexadecyltrimethyl ammonium (HDTMA) amount equal to the 100% of the ECEC of zeolite Y. Synthesized SMZY remove Cr(VI) and As(V) more than the corresponding commercial one due to its lower silica to alumina ratio. Thus, the HDTMA-covered modified zeolite Y synthesized using RHA can be used to remove Cr(VI) and As(V) from water.     

Modified carbon paste electrodes for Cu(II) determination

A new Cu²⁺ carbon paste electrode (CPE) using 2,2′-(1E,1′E)-1,1′-(2,2′-azanediylbis (ethane-2,1-diyl)bis(azan-1-yl-1-ylidene))bis(ethan-1-yl-1-ylidene)diphenol (ADEZEDP) has been prepared. The influence of variables including sodium tetraphenylborate (NaTPB), ionophore, and amount of multiwalled carbon nanotubes (MWCNT), CdO nanowires, CdS nanoparticles and palladium nanoparticles loaded on ADEZEDP and Nujol on the electrodes response were studied and optimized. At optimum values of all variables, for each nanomaterial the electrode response was linear in concentration range of 1.0 × 10^? 8 to 1.0 × 10^? 1 mol L^? 1 for ADEZEDP with Nernstian slope. The good performance of electrode viz. Wide applicable pH range (2.0–5.0), fast response time (≈ 6 s), and adequate life time (3 months) indicate the utility of the proposed electrodes for evaluation of Cu²⁺ ion content in various situations. Finally, these electrodes have been successfully applied for the determination of Cu²⁺ ions content in various real samples. The selectivity of proposed electrode was evaluated by separation solution method and fixed interference method.     

On the Characterization of Thermal-Conductivity Degradation During Torsional Fatigue

The thermal conductivity of a metal, subjected to cyclic loading, changes as it degrades due to the appearance of micro-cracks and micro-voids. This continues up to the critical stage where macro-cracks are created and failure occurs. In this study, a theoretical model for thermal-conductivity deterioration is presented that accounts for the cyclic loading. To examine the validity of the results obtained from a theoretical model, an apparatus is designed to measure thermal-conductivity degradation by means of the guarded-comparative-longitudinal heat-flow technique. Results of a series of thermal-conductivity measurements at several stages of torsional fatigue tests are presented. It is shown that the thermal conductivity of Al 6061-T6 decreases approximately 8 % to 12 % before complete failure takes place.     

A Numerical and Experimental Investigation into Hot Stamping of Boron Alloyed Heat Treated Steels

Hot stamping of steel sheets using water or nitrogen cooling media was studied on a laboratory scale. Sheets of grade 22MnB5 boron steels in three different thicknesses were investigated and the results of experimental hot stamping tests were considered. Microstructural analysis, linear and surface hardness profiling as well as tensile tests of formed samples were carried out. After hot stamping, mostly fully martensitic microstructures, which yield ultra high strength levels, were produced. It is concluded that die cooling media, i.e., water or nitrogen, have a significant effect on material properties after hot stamping. Using liquid nitrogen as coolant in the punch instead of water increases yield strength by 50 to 65MPa. Moreover, the evolution of the temperature and force during the hot stamping process was simulated by using a coupled thermomechanical FEM program. The results of numerical simulation and experimental results are in good agreement.     

High-power potassium titanyl phosphate laser vaporization prostatectomy

PURPOSE: To determine whether central venous pressure at the common iliac vein reflects right atrial pressure in adult patients. METHODS: In this prospective, non-blinded study 26 mechanically-ventilated adult patients were studied. Simultaneous pressure readings were obtained from the right atrium (TCVP) and the common iliac vein (ACVP). RESULTS: There was a correlation between TCVP and ACVP (r = 0.987; P < 0.0001). The mean difference between TCVP and ACVP was 0.93 mm Hg. And the limits of agreement were: -1.93 to 1.77 mm Hg. CONCLUSION: Venous pressure recorded from the common iliac vein reflects that in the right atrium. Adopting a femoral route for central venous pressure measurement may avoid some of the complications associated with the subclavian route.     

Analysis of Microstructure and Mechanical Properties of Different Hot Stamped B‐bearing Steels

Hot stamping is a technique to produce ultra high strength automobile components. The common material used in hot stamping process is coated and/or uncoated 22MnB5 boron alloyed steel. Ferritic‐pearlitic microstructure in as‐delivered sheets is transformed to fully lath martensitic after hot stamping. In the present research, hot stamping under water or nitrogen cooling media was investigated using different boron alloyed steel grades. Microstructural analyses, linear and surface hardness profiling as well as tensile tests of hot stamped samples were performed. Various microstructures of fully bainitic and/or fully martensitic were produced. The resulting microstructures provided yield strengths of 650–1370 MPa and tensile strengths of 850–2000 MPa. There is an optimum carbon equivalent content for which the highest formability index value, UTS × A₂₅, is achieved. Using a nitrogen cooled punch resulted in higher yield strength without significant changes in ultimate tensile strength. It is concluded that a wide range of B‐bearing steels having an extended carbon equivalent range with an acceptable formability index value can be used by increasing the cooling rate in the die assembly.     

MAC-layer channel utilisation enhancements for wireless mesh networks

The authors focus on a wireless mesh network, that is, an ad hoc IEEE 802.11-based network whose nodes are either user devices or Access Points providing access to the mesh network or to the Internet. By relying on some work done within the IEEE 802.11s TG, the network nodes can use one control channel and one or more data channels, each on separate frequencies. Then, some problems related to channel access are identified and a MAC scheme is proposed that specifically addresses the problem of hidden terminals and the problem of coexisting control and data traffic on different frequency channels. An analytical model of the MAC scheme is presented and validated by using the Omnet++ simulator. Through the developed model, we show that our solution achieves very good performance both in regular and in very fragmented mesh topologies, and it significantly outperforms the standard 802.11 solution.     

Cervical spondylotic myelopathy: surgical results and factors affecting prognosis

OBJECTIVE: A variety of factors may affect surgical outcome in patients with cervical spondylotic myelopathy. The aim of this study is to determine these factors on the basis of preoperative radiological and clinical data. METHODS: To assess the factors affecting postoperative outcome after surgery for cervical spondylotic myelopathy, the clinical and radiological data of 27 patients with cervical spondylotic myelopathy were reviewed. Functional and neurological statuses were assessed using the Japanese Orthopaedic Association (JOA) scale modified by Benzel. In all patients, the effect of age, symptom duration, cervical curvature, presence or absence of preoperative high signal intensity within the spinal cord as revealed by T2-weighted magnetic resonance imaging, and diameters of the spinal canal and vertebral body on pre- and postoperative neurological statuses were investigated. Plain radiographs were obtained for all patients, magnetic resonance images for 21 patients (77.8%), computed tomographic scans for 13 patients (48.1%), myelograms for 6 patients (22.2%), and computed tomographic myelograms for 4 patients (14.8%). There were five patients with a JOA score of 10, six patients with a JOA score of 11, six patients with a JOA score of 12, four patients with a JOA score of 13, four patients with a JOA score of 14, one patient with a JOA score of 15, and one patient with a JOA score of 16. All patients underwent cervical laminectomies. The mean follow-up period was 54.1 months. The final neurological examinations revealed improvement in the JOA scores of 85.1 % of the patients. RESULTS: Statistical analysis of all patients revealed mean JOA scores of 12.185 +/- 1.618 and 14.370 +/- 2.15 before surgery and at final examination, respectively. The difference between the preoperative JOA score and the final JOA score was determined to be statistically significant (P < 0.0001). Statistical analyses also showed better neurological improvement in patients younger than 60 years and in patients with normal preoperative cervical lordosis. Although patients without preoperative high signal intensity of the spinal cord showed a better improvement rate than did patients with preoperative high signal intensity, the determined difference was statistically insignificant. CONCLUSION: It can be concluded that age and abnormal cervical curvature predict less postoperative neurological improvement. The presence of preoperative high signal intensity within the spinal cord may also reflect less neurological improvement.