Effects of Various Energy Suppliers in Green Processes for Obtaining Silver Nanoparticles

The productions of stable suspensions of silver nanoparticles using a microwave reactor, an ultraviolet (UV) reactor, a low‐frequency low‐temperature plasma reactor, a high‐pressure reactor, and an open reactor are compared. All reactors served as sources of energy for stimulating the nanoparticle growth process. The silver nanoparticles were obtained based on the chemical reduction method. The processes were conducted using gallic acid as the reducing‐stabilizing substance. The influence of the variable parameters time (for all types of reactors), temperature (for the open and high‐pressure reactors), power (for the microwave reactor), energy density (for the UV reactor), and voltage (for the low‐frequency low‐temperature plasma reactor) was investigated. Temperature was found to be the most important factor influencing all processes.     

Flow patterns and gas fractions of air–oil and air–water flow in pipe bends

An experimental study of two-phase flow in a 180° pipe bends with 0.016, 0.022 and 0.03 m and the curvature radii of 0.11, 0.154, 0.21 m, respectively have been carried out. The experiments were conducted under the input superficial phase velocity: air from 0.038 to 5.4 m s⁻¹, water from 0.018 to 0.92 m s⁻¹ and oil from 0.014 to 0.92 m s⁻¹. The conducted research involved the observation of the forming flow patterns and determination of average volumetric in situ gas fraction. On the basis of the results of experimental flow map was created for gas–liquid flow and a method of calculating gas fractions was established.     

Fluidity and Temperature Profile of Ductile Iron in Thin Sections

 It has been shown that it is possible to produce thin wall ductile iron (TWDI) castings of considerable length using an Archimedes spirals with a wall of 1, 2 or 3 mm in thickness. The fluidities for different moulding materials ［(classical mould, chemically bonded silica sand and chemically bonded low-density alumina-silicate ceramic sand (LDASC)］, chemical composition, and pouring temperature were estimated. There is a significant temperature drop in thin sections (contrary to typical sections) during the mould filling. A profile of real temperature drop is presented along with theoretical predictions. The high temperature drop of liquid iron results in an increased cooling rate (before the eutectic equilibrium solidification temperature), which in turn affects the solidification and microstructure of TWDI castings. Microstructures were characterized quantitatively using an image analyser. Structure parameters for different wall thicknesses and moulding materials (graphite nodule count, ferrite and cementite fraction) are plotted, which is versus distance from the entrance to the mould cavity. It has been shown that the thin wall castings have a gradient structure. Moreover, a strong influence of LDASC sand (material with low ability to absorb the heat) on the structure parameters of TWDI castings is presented.     

Thermal and electrical conductivity of melt mixed polycarbonate hybrid composites co‐filled with multi‐walled carbon nanotubes and graphene nanoplatelets

In this work, we present thermoplastic nanocomposites of polycarbonate (PC) matrix with hybrid nanofillers system formed by a melt‐mixing approach. Various concentrations of multi‐walled carbon nanotubes (MWCNT) and graphene nanoplatelets (GnP) were mixed in to PC and the melt was homogenized. The nanocomposites were compression molded and characterized by different techniques. Torque dependence on the nanofiller composition increased with the presence of carbon nanotubes. The synergy of carbon nanotubes and GnP showed exponential increase of thermal conductivity, which was compared to logarithmic increase for nanocomposite with no MWCNT. Decrease of Shore A hardness at elevated loads present for all investigated nanocomposites was correlated with the expected low homogeneity caused by a low shear during melt‐mixing. Mathematical model was used to calculate elastic modulus from Shore A tests results. Vicat softening temperature (VST) showed opposite pattern for hybrid nanocomposites and for PC‐MWCNT increasing in the latter case. Electrical conductivity boost was explained by the collective effect of high nanofiller loads and synergy of MWCNT and GnP. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42536.     

Elaboration of small‐diameter vascular prostheses—Selection of appropriate sterilisation method

The aim of study is the elaboration of semi‐biodegradable, multilayered tubular structures as substitutes for the reconstruction of small diameter vascular prostheses (<6 mm). The inert external layer of the prostheses will be fabricated via the melt electrospinning of poly (l ‐lactide‐co‐glycolide) (PLGA). The middle layer will be constructed from polypropylene (PP); the first prototype will be produced via melt electrospinning and the second using the melt blowing technique. The general aim of this stage of the research is the selection of a sterilisation technique that is appropriate for semi‐biodegradable, multilayered tubular structures. For this purpose, single tubular structures created via the melt electrospinning of PLGA or PP and melt blown tubular structures of PP were elaborated. The influence of steam, ethylene‐oxide (EO), and radiation sterilisation techniques on the elaborated microstructure of tubular structures was analyzed during this study. The effect of each sterilisation technique was evaluated using differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy/energy‐dispersive X‐ray spectroscopy analysis (SEM/EDS). The changes in average molecular weight (M_w) and crystallinity index (CI) of the PLGA tubular structures after EO and steam sterilisation were evaluated. The EO and steam sterilisation resulted in the complete destruction of PLGA tubular structures. Only the radiation sterilisation (accelerated electrons) did not influence on PLGA tubular structures morphology as well as thermal and chemical properties. FTIR and SEM/EDS analysis indicated that no changes in the chemical properties of PP tubular structures after each sterilisation occurred. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40812.     

Small diameter tubular structure design using solvent‐free textile techniques

The aim of research was to elaborate the non‐biodegradable (made of polypropylene (PP)) and resorbable (made of polylactide (PLA)) tubular fibrous structures for the reconstruction of the vascular vessels. For the mentioned structures design, nonconventional manufacturing techniques such as melt blown, melt electrospinning, and melt electroblowing were used. Three techniques were chosen as methods allowing on the fibrous structures manufacture containing fibers in nano‐ or submicro‐size diameter. Other advantages of free‐solvent technique use is the reduction in the clinical adverse events associated with solvent resided in the fibrous structure during the fabrication. The tubular fibrous structures of PP and PLA using above‐mentioned techniques were designed. In first stage, the analysis of the processing parameters influence on the nonbiodegradable and biodegradable tubular structures fiber diameter was performed. Subsequently, the validation step was the analysis of the influence of processing parameters on PP and PLA structural properties for each manufacturing techniques was investigated. The research results confirmed the ability of the tubular structures manufacture with various fiber diameter depending on the applied technique and processing parameters. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40147.