Controlled undercooling of liquid iron in contact with ZrO2 and MgO substrates under varying oxygen partial pressures

The objective of this study is to determine the conditions under which the inclusions present in liquid steel can act as heterogeneous nucleants for solidification. In order to study the factors that define the undercooling of a given metal/oxide couple, the undercooling of a pure iron sessile droplet in contact with Al₂O₃, ZrO₂, and MgO substrates was measured under controlled oxygen partial pressures by observing droplet recalescence. The results showed that the undercooling of iron, in contact with a particular substrate, did not have a unique value, but was significantly affected by the oxygen content on the gas phase. For oxygen partial pressures between 10⁻²¹ and 10⁻¹⁹, the undercooling of iron on ZrO₂ substrates was stable and around 290 °C. In the same range of oxygen partial pressure, the undercooling of iron on MgO substrates remained below 100 °C due to the low stability of this oxide. At lower oxygen contents, substrate decomposition might be the cause for the observed drop in the undercooling of iron on ZrO₂ substrates to below 100 °C. The undercooling also decreased for increasing oxygen content as verified when the gas was changed from gettered Ar/Ar-H₂ to CO/CO₂ mixtures. The variation in undercooling was related to the wetting of the substrate by the liquid metal, where the deep undercooling observed in the ZrO₂ experiments occurred when the highest contact angle between the liquid metal and the substrate was achieved.     

IPv6 delay and loss performance evolution

Although packet delay and loss are two important parameters of the Internet performance, to the best of our knowledge, the evolution of large‐scale IPv6 delay and loss performance has previously not been studied. In this paper, we analyze more than 600 end‐to‐end IPv6 paths between about 26 testboxes of RIPE Network Coordination Centre over two years, and compare the delay and loss performance over time with their IPv4 counterparts. We present and discuss the measurement methodologies and show that IPv6 paths have a higher delay and loss than their IPv4 counterparts. The main reason for the worse performance stems from IPv6‐in‐IPv4 tunnels rather than from native IPv6 paths and such tunnels are still widely used today. Copyright © 2007 John Wiley & Sons, Ltd.     

What do we know about innovation in nanotechnology? Some propositions about an emerging field between hype and path-dependency

This contribution formulates a number of propositions about the emergence of novel nanoscience and nanotechnology (N&N). Seeking to complement recent work that aims to define a research agenda and draws on general insights from the innovation literature, this paper aims to synthesize knowledge from innovation-related studies of the N&N field. More specifically, it is suggested that N&N is often misconstrued as either a field of technology or an area of (broadly) converging technologies while evidence to date suggests rather that N&N be considered a set of inter-related and overlapping about not necessarily merging technologies. The role of instrumentation in connecting the various N&N fields is underlined. Finally, the question is raised whether change in N&N tends to be incremental rather than discontinuous, being the result of technological path-dependencies and lock-ins in industry-typical search regimes that are only slowly giving way to more boundary-crossing activities.     

Degradation of Stiffness of Cemented Calcareous Soil in Cyclic Triaxial Tests

The deformation characteristics of artificially cemented calcareous soil subjected to undrained cyclic triaxial loading are investigated at different confining pressure and cyclic stress levels. The influence of cementation on the shear stiffness is investigated by comparing the behavior of cemented and uncemented soils with similar initial conditions. It is observed that the deviator stress and the deviatoric strain at yield reduced with increasing number of cycles for cemented sand due to progressive degradation of bond, which results in significant decrease in stiffness. On the other hand, a strain-hardening effect is observed in uncemented sand and this results in increasing yield stress and strain with progressive number of cycles. A linear relationship between degradation index and number of cycles is observed for cemented sand. This relationship has been synthesized in the form of an empirical equation by modifying a previously proposed equation for cohesive soils. This empirical equation was further used to evaluate the fatigue life of soils by adopting a failure criterion.     

Failure of a stationary pump engine piston

Piston failures are not a common occurrence, but they do occur, and failure is usually associated with fatigue crack growth. Most failures initiate at the gudgeon pin hole or in the skirt of the piston. Occasionally they fail elsewhere. In the example covered in this paper, failure initiated in the crown and progressed down to the gudgeon pin before final failure occurred. This paper outlines the cause and mode of failure and shows that small metallurgical discontinuities can contribute to these failures under the right circumstances.     

Examining a curvilinear relationship between communication frequency and team performance in cross-functional project teams

The performance of a cross-functional team depends on the skillful and innovative combination of information and expertise from all team members. Communication is the medium through which team members share the information required for successful amalgamation. In this work, we postulate that both high and low levels of team communication can impede team performance, thus leading to a curvilinear relationship between team performance and team communication. To test this hypothesis, the relationships between face-to-face, e-mail, and telephone communication and team performance were examined for 60 cross-functional project teams. E-mail and face-to-face communication were curvilinearly associated with performance, but telephone communication was not. Further analysis of the communication frequency between colocations showed that e-mail is the only medium for which usage increased with distance.     

Delamination Resistant Zinc Alloys: Simple Concept and Results on the System Zinc‐Magnesium

Alloying zinc coatings with elements such as magnesium and titanium increases the corrosion resistance in industrial tests. Based on the fundamental mechanism of cathodic delamination, a simple concept how alloying zinc with specific elements might improve its resistance to cathodic delamination is presented in this paper. As an example, results concerning the delamination of a simple polymer from the zinc‐magnesium intermetallic MgZn₂ are presented. From electrode potential measurements obtained with the Scanning Kelvin Probe it can be concluded that cathodic delamination from this alloy is completely inhibited. This behaviour is attributed to the electronic properties of the magnesium‐rich oxidic passive layer, that inhibits the oxygen reduction reaction at the metal oxide/polymer interface.