An image processing system using Image Signal Multiprocessors (ISMPs)

This paper describes an image processing system using Image Signal Multiprocessors (ISMPs) adapted to gray-level image preprocessing for image analysis and image enhancement. It is composed of four ISMPs, five 1H-delay-lines, two 512×512×8-bit frame memories, a video timing controller (VTC), two 256-word ×8-bit ×8-table Look Up Tables (LUTs) and 80 nsec/sampling A/D and D/A converters. This multiprocessor system performs convolution operations such as spatial filters, contrast enhancement, and binarization for gray-level images, thinning, thickening, pattern matching etc. for binary images, and image quality improvement for moving images such as T.V. images. Otherwise, it performs feature extraction operations such as area calculations, fillet coordination, and moment calculations for objective image data. Moreover, this system is capable of applying color image processing by using a multiboard system.     

Optical Energy Gap and Below Gap Optical Absorption of Fullerene Films Measured by the Constant Photocurrent Method and Photothermal Deflection Spectroscopy

The CPM spectra of fullerene films was measured to obtain the below gap absorption. The optical energy gap E_o was obtained by using the Tauc's plots. E_o did not change greatly with intercalated impurities. The absorption due to intercalated impurities was found below 1.6eV.     

Comparison of coal hydroliquefaction catalysed by ZnCl2-MCln (CuCl,CrCl3 and MoCl5) and ZnCl2 melts

Hydrogenation of four bituminous coals impregnated with 5 wt% of either mixtures of ZnCl₂-MCl_n (CuCl, CrCl₃ and MoCl₅) systems or ZnCl₂ was carried out using a batch autoclave system at 400° for 3 h at 9.8 MPa of initial hydrogen pressure. The ZnCl₂-MoCl₅ system showed the highest yield of the hexane-soluble (HS) fraction compared with the other systems irrespective of the coal used. The difference between the yields of HS fractions using the ZnCl₂-MoCl₅ and other systems was most marked for coals of fairly low volatile matter content, though the conversion was relatively low (47–66%), whilst for coals of high volatile matter content HS yields with the binary melt systems were high (86–91% conversion). Elemental analyses of the HS fractions indicated that the ZnCl₂-MoCl₅ system is most favourable in decreasing the average molecular weight and the heteroatom content of HS, this characteristic trend being confirmed also with five HS fractions separated by Chromatographic techniques. Both elemental analyses and molecular weights of asphaltene (benzene-soluble materials, BS) indicated that the ZnCl₂-MoCl₅ system is also most effective in cracking coal structure.     

Study on modified phenolic resin. I. Modification with homopolymer prepared from p-hydroxyphenylmaleimide

We studied the improvement of heat resistance and mechanical properties of phenolic resin modified with polymers prepared from p-hydroxyphenylmaleimide (HPMI). Homopolymers of HPMI and copolymers of HPMI with some vinyl monomers were synthesized and M_n T_g and thermal decomposition temperature of them were measured by GPC, DSC, and TG, respectively. The miscibility of homopolymer with novolac was examined by DSC. It was found that the homopolymer had good heat resistance and good miscibility with novolac. Molding compounds were prepared by hot roll-kneading the mixtures of novolac, the homopolymer, hexamethylenetetramine, and glass fiber. It was found that molded test pieces had good heat resistance.     

Examination of acetolysis products of phosphatidylcholine by gas chromatography-mass spectrometry

A comparison of monoacetyldiglycerides obtained from authentic phosphatidylcholines by acetolysis with those obtained by phospholipase C-acetylation was made to examine the intermolecular acyl migration, the intramolecular acyl migration between C-1 and C-2, and the formation of 1,3-isomer in the acetolysis reaction. Egg yolk phosphatidylcholine also was used. It was revealed that is acetolysis, the intermolecular acyl migration and selective degradation of polyunsaturated fatty acids did not take place at all. The intramolecular acyl migration, including the formation of 1,3-isomer, occurred to a small extent. Appreciable difference was not found in comparison of molecular species compositions of monoacetyldiglycerides derived by both methods from egg yolk phosphatidylcholine, except small differences found in the contents of two kinds of molecular species.     

Network formation and swelling behavior of photosensitive poly(vinyl alcohol) gels prepared by photogenerated crosslinking

Poly (vinyl alcohol) with pendent styrylpyridinium groups (SbQ) is insolubilized by photoirradiation. An association takes place in SbQ groups. The association of polymer chains becomes marked with increasing the number of SbQ groups. Mainly intermolecular crosslinks were formed. Transparent and homogeneous macrogels consisting of several intermolecular crosslinks are obtained. The proportion of the free water to the bound water in PVA-SbQ gels was 3.3?2.9 despite of the large change in conversion of photodimerization of SbQ groups, x=0.27?0.58. The water uptake after swelling of the gels in water increased 6–27 times compared to the original weight at pH=7. The higher the degree of photocrosslinking, the lower was the degree of swelling. The water diffusion coefficients, D, were (2.2?5.8) × 10^?5 cm² S^?1 for a 88% saponified PVA with 1 . 3 mol% SbQ groups. The volume of the gel increased discontinuously about 10-fold for the 99% saponified PVA with 0 . 096 mol% SbQ and 51% water (49% acetone). The acetone concentration at the transition decreased with increasing the degree of saponification of the PVA.     

Stepwise increase of hardness in the curing process of one-step phenolic folding compounds

The curing behavior of one-step phenolic molding compounds was studied using results of Rockwell hardness measurements at elevated temperatures with a cone indenter. The curing process was found to advance in a stepwise manner to the final stage of cure at a specific temperature. An explanation for this phenomenon has been attempted by suggesting the alternating occurrence of two types of curing reactions—propagation and crosslinking. After proceeding to some extent of cure, only the propagation reaction can occur through the migration of low molecular resin to the reactive sites of polymer chains. The propagation facilitates the subsequent crosslinking which drastically enhances the hardness of the resin. The results of electrical resistivity measurements and acetone extraction tests were also found to support the occurrence of above phenomenon.     

Characterization of Silicon Carbide–Silicon Nitride Composite Ultrafine Particles Synthesized Using a CO2 Laser by Silicon-29 Magic Angle Spinning NMR and ESR

The structure of silicon carbide–silicon nitride (SiC–Si₃N₄) composite particles synthesized using a CO₂ laser was studied by magic angle spinning nuclear magnetic resonance (MAS-NMR) and electron spin resonance (ESR). The structure around Si atoms changed by introducing N. C atoms around Si were substituted by N atoms, and N-rich configurations around Si atoms increased stepwise as the N content increased. The low N content composite particles consisted of mainly SiC phase containing dissolved N. N atoms were partly present in β-SiC microcrystal and partly in the grain boundary layer in the particle. N atoms were tetrahedrally surrounded by four Si atoms in β-SiC microcrystal and were trivalent state bonded to three Si atoms in the grain boundary layer. The high N content particles consisted of SiC, Si₃N₄, and amorphous phases, whose amount depended on N content.     

Preparation of Titanium Nitride Films from Amide Precursors Synthesized by Electrolysis

A TiN precursor solution was synthesized by galvanostatic electrolysis of Ti metal and isopropylamine at a current density of 50 mA·cm⁻² at room temperature. TiN films were prepared by dip-coating of the precursor solution on a Si wafer, followed by two-stage heat treatment at 400°C and a fixed temperature of 800–1200°C in flowing N₂, N₂/NH₃, or NH₃ gas. The TiN films were characterized by XRD, chemical analysis, XPS, and electrical resistivity measurements. The TiN films were composed of uniform grains 20 to 200 nm in size with thicknesses ranging from 300 to 400 nm at temperatures of 800–1200°C. The effect of the heat treatment atmosphere (N₂ and NH₃) on the impurity content, crystallinity, particle size, and electrical resistivity is discussed.