4-(2-噻唑偶氮)-5-二甲氨基苯胺与铑(Ⅲ)显色反应研究及其应用

研究了显色剂 4 ( 2 噻唑偶氮 ) 5 二甲氨基苯胺 (简称TADMA)与铑 的显色反应。结果表明 ,在 pH3 2～ 4 8范围内 ,铑 与TADMA反应形成 1∶2红色络合物 ,加入无机酸后色泽加深 ,络合物的表观摩尔吸光系数为 1 2 1× 10 5,铑质量浓度在 0～ 0 92 μg/mL范围内服从比尔定律。本方法操作简便 ,灵敏度高 ,选择性好 ,常见金属离子在一定范围内无干扰 ,用于催化剂中微量铑的测定 ,结果满意     

Disc filtration for separation of flocs from a moving bed bio-film reactor.

A Discfilter with 10 and 18 microm filter openings, respectively, was placed in parallel to a flotation plant for separation of biological flocs from a post-denitrifying Kaldnes Moving Bed Process, the last treatment step at the municipal wastewater treatment plant at Sj?unda, Malm?, Sweden. The effluent concentrations from the 10 and 18 microm filter were 2-5 and 2-8 mg SS L(-1), respectively, which is comparable to, or better than, the flotation plant. Comparison with experiences from activated sludge plants shows that the Discfilter works especially well after the Kaldnes process. Particle size distribution (PSD) studies show that particles larger than the filter openings of 10 and 18 microm are separated with approximately 90% efficiency, whereas most of the smaller particles pass the filter. This fact indicates that the major particle separation mechanism is physical blocking. These findings point to the possibility of improving the prediction of the separation efficiency by combining measurements of turbidity and suspended solids with particle size analysis.     

Textilspanplatten

Ohne Zusammenfassung     

Study of the morphology and mechanical properties of polypropylene composites with silica or rice‐husk

The mechanical, morphological behavior and water absorption characteristics of polypropylene (PP) and silica, or PP and rice‐husk, composites have been studied. The silica used in this study as filler was a commercial type produced from soluble glass or rice husks. The compatibilizing effect of PP grafted with monomethyl itaconate (PP‐g‐MMI) and/or with vinyltriethoxysilane (PP‐g‐VTES) as polar monomers on the mechanical properties and water absorption was also investigated. In general, a high loading of the studied fillers in the polymer matrix increases the stiffness and the water absorption capacity. This effect is more noticeable in the tensile modulus of the PP/silica composite with PP‐g‐VTES as compatibilizer. However, the increase of the rice‐husk charge as a natural filler in the PP matrix decreases the stiffness, and in the presence of PP‐g‐MMI as compatibilizer in PP/rice‐husk, the tensile modulus and water absorption of the composite were improved. The better adhesion and phase continuity in the PP/silica and PP/rice‐husk composites with different compatibilizers was confirmed by the morphological study. Copyright © 2004 Society of Chemical Industry     

发展中的ATCA顺从设备技术

设计一种新的系统底板涉及到很多准则,其中包括各种专用功能以及构成任何电信或数据系统一部分的通用模块.这些通用模块,如机械设计、EMI完整性、底板、电源和机架管理,是所有设计共有的.它们对设计的标新立异没有贡献,而且从研发角度来看,可以看作是额外开销.另一方面,与系统有关的特性则是设备专有的,也是实现方法所独有的,并会使系统厂商引入新颖而独特的功能,使其产品不同于竞争对手的产品.     

Challenges in the Application of Stochastic Modal Identification Methods to a Cable-Stayed Bridge

This paper presents an analysis of the data collected in the ambient vibration test of the International Guadiana cable-stayed Bridge, which links Portugal and Spain, based on different output-only identification techniques: peak-picking, frequency domain decomposition, covariance-driven stochastic subspace identification, and data-driven stochastic subspace identification. The purpose of the analysis is to compare the performance of the four techniques and evaluate their efficiency in dealing with specific challenges involved in the modal identification of the tested cable-stayed bridge, namely the existence of closely spaced modes, the perturbation produced by the local vibration of stay-cables, and the variation of modal damping coefficients with wind velocity. The identified natural frequencies and mode shapes are compared with the corresponding modal parameters provided by a previously developed numerical model. Additionally, the variability of some modal damping coefficients is related with the variation of the wind characteristics and associated with a component of aerodynamic damping.     

Pretreatment of Highly Polluted Pharmaceutical Waste Broth by Wet Air Oxidation

The preoxidation of a highly polluted waste pharmaceutical fermentation broth using wet air oxidation (WAO) has been studied as a possible method for the effective removal of organics. The applied (pre)treatment method should enhance the biotreatability of the pharmaceutical fermentation broth in terms of reduced initial toxicity and higher biodegradability. Preliminary experiments in the pilot biological treatment plant were successful only at low organic loads, whereas the system collapses at higher ones. The characterization of the fermentation broth was started by common physicochemical analysis, whereas several bioassays were used to determine its impact on biological treatment plants and the environment. Toxicity prior to and after WAO was determined using the acute Vibrio fischeri test, measurement of inhibition of O2 consumption, and the Daphnia magna acute test. Ready biodegradability of the treated and untreated broth has also been assessed. WAO experiments were accomplished in the 2?L batch reactor at different temperatures (240/280°C) and operating pressures. WAO experiments confirmed reduction of the toxicity toward microorganisms, whereas oxidized wastewater was more toxic to daphnids. Biodegradability of the oxidized broth has also been enhanced. Further work has been focused on designing appropriate combination of WAO and biological processes.     

Stochastic nonlinear stabilization — II: Inverse optimality

After considering the stabilization of a specific class of stochastic nonlinear systems in a companion paper, in this second part, we address the classical question of when is a stabilizing (in probability) controller optimal and show that for every system with a stochastic control Lyapunov function it is possible to construct a controller which is optimal with respect to a meaningful cost functional. Then we return to the problem from Part I and design an optimal backstepping controller whose cost functional includes penalty on control effort and which has an infinite gain margin.