Pack cementation process for the formation of refractory metal modified aluminide coatings on nickel-base superalloys

The vapour phase compositions of a series of pack powder mixtures containing elemental Al and Hf or W powders as depositing sources and CrCl₃·6H₂O or AlF₃or CrF₃as activators were analysed in an attempt to further develop the pack cementation process to codeposit Al and Hf or W to form diffusion coatings on nickel base superalloys. The results suggested that Al could be codeposited with Hf, but not with W, from the vapour phase. Compared with both AlF₃and CrF₃, CrCl₃·6H₂O has been shown to be a more suitable activator for codepositing Al with Hf. The optimum coating temperature was identified to be in the range of 1050°C to 1150°C. Based on the thermochemical analysis, a series of coating deposition studies were undertaken, which confirmed that codeposition of Al and Hf could be achieved at a deposition temperature of 1100°C in the CrCl₃·6H₂O activated packs containing elemental Al and Hf powders. The coating obtained had a multilayer structure consisting of a Ni₇Hf₆Al₁₆top layer and a NiAl layer underneath, followed by a diffusion zone, which revealed that the coating was formed by the outward Ni diffusion. It is suggested that the compositions suitable for codeposition of Al and Hf could be effectively identified by comparing the vapour pressures of HfCl₄and HfCl₃with that of AlCl in the packs activated by chloride salts. It has also been experimentally demonstrated that, although W could not be deposited from the vapour phase, a high volume of fine W particles can be entrapped into the outer NiAl coating layer formed by the outward Ni diffusion using a modified pack configuration. This leads to the formation of a composite coating layer with W particles evenly distributed in a matrix of NiAl. It is suggested that this modified pack process could be similarly applied to develop nickel aluminide coatings containing other refractory metals that may not be codeposited with Al from the vapour phase.     

Asymptotic performance of single parity-check product codes

This article investigates the asymptotic performance of single parity-check (SPC) product codes (PCs) from a decoding point of view. Specifically, the probability of bit error is bounded before and after the decoding of each dimension, similar to the analysis of "iterated codes" by Elias (1954). It is shown that the asymptotic probability of bit error can be driven to zero as the number of dimensions, and hence the block length, increases at signal-to-noise ratios (SNRs) within 2 dB of capacity over the additive white Gaussian noise (AWGN) channel.     

High-efficiency LEDs of 1.6–2.4 µm spectral range for medical diagnostics and environment monitoring

High efficient LED structures covering the spectral range of 1.6–2.4 μm have been developed on the basis of GaSb and its solid solutions. The electroluminescent characteristics and their temperature and current dependences have been studied. The radiative and nonradiative recombination mechanisms and their effect on the quantum efficiency have been investigated. A quantum efficiency of 40–60% has been obtained in the quasi-steady mode at room temperature. A short-pulse optical power of 170 mW was reached. __________ Translated from Fizika i Tekhnika Poluprovodnikov, Vol. 37, No. 8, 2003, pp. 996–1009. Original Russian Text Copyright ? 2003 by Stoyanov, Zhurtanov, Astakhova, Imenkov, Yakovlev.     

Why does it pay to be selfish in a MANET?

Routing protocols for a mobile ad hoc network have assumed that all mobile nodes voluntarily participate in forwarding others' packets. This was a reasonable assumption because all MNs in a MANET belonged to a single authority. In the near future, however, a MANET may consist of MNs that belong to many different organizations since numerous civilian applications are expected to crop up. In this situation, some MNs may run independently and purposely decide not to forward packets so as to save their own energy. This could potentially lead to network partitioning and corresponding performance degradation. To minimize such situations in MANETs, many studies have explored the use of both the carrot and the stick approaches by having reputation-based, credit-payment, and game theory schemes. This article summarizes existing schemes, identifies their relative advantages, and projects future directions     

Application of extended boundary conditions and the Haar wavelets in the analysis of wave scattering by thin screens

A recent approach to solution of 2D scattering problems for electromagnetic waves scattered by thin screens is analyzed. With the use of examples of scattering by a strip and an unclosed cylindrical surface, it is shown that the proposed approach has no advantages in terms of the efficiency of numerical solution over a well-known approach based on exact integral equations for currents that have singular kernels and that are solved with the Krylov-Bogoliubov method.     

Parametric effects on the transient Voltage performance of a DC superconducting cable

The objective of this work was to determine the significant parameters of a 3-GW 200-kV dc superconducting cable system which influence the transient voltage distribution in the various parts of the cable. The cable system consists of four coaxial metallic cylinders. It was found that the dielectric constant and the electrical resistivity of the soil significantly affect the severity of the transient voltages; lower dielectric constant and higher resistivity of the soil will increase the magnitudes of the transient voltages by increasing the earth-return impedance. It was also found that the effect of the conductor internal impedances of the cable is insignificant. Shorting the coaxial cylinders of the cryogen flow and the cryostat will lessen the severity of the transient voltages. Grounding the second, third, and fourth cylinders at regular intervals with low-impedance grounding impedance will also improve the transient performance of the cable. More research is needed to evaluate these procedures.     

Nanoscale Crystallization in Amorphous Fe–P–Mn Alloys

Mössbauer effect measurements and physicochemical analysis demonstrate that annealing of amorphous Fe–P–Mn alloys leads to the formation of a nanocrystalline structure.     

Fabrication, assembly, and characterization of molecular electronic components

One of the ultimate miniaturizations in nanotechnology is molecular electronics, where devices will consist of individual molecules. There are many complications associated with the use of molecules in electronic devices, such as the electronic perturbations in the molecule associated with being bonded to an electrode, how electrons traverse the metal-molecule junction, and the difficulty of macroscopically addressing single to very few molecules. Whether fabricating a test structure or a usable device, the use of self-assembly is fundamental to the fabrication of molecular electronic devices. We will discuss how to fabricate self-assembled monolayers into test assemblies and how to use intermolecular interactions to direct molecules into desired positions to create nanostructures and to connect functional molecules to the outside world. These assemblies serve as test structures for measurements on single or bundled molecules. The development of several experimental techniques, including various scanning probes, mercury drop junctions, break junctions, nanopores, crossed wires, and other techniques using nanoparticles have enabled the ability to test these structures and make reproducible measurements on single molecules. Many of these methods have been developed to test molecules with potential for integration into devices such as oligo (phenylene-ethynylene) molecules and other /spl pi/-conjugated molecules, in ensemble or single-molecule measurements.     

TEM Studies of High Temperature Corrosion Behaviour of TiAl Intermetallics with Surface Modifications

The oxidation/sulphidation behaviour of a Ti‐46.7Al‐1.9W‐0.5Si alloy with a TiAl₃ diffusion coating was studied in an environment of H₂/H₂S/H₂O at 850^oC. The kinetic results demonstrate that the TiAl₃ coating significantly increased the high temperature corrosion resistance of Ti‐46.7Al‐1.9W‐0.5Si. The SEM, EDX, XRD and TEM analysis reveals that the formation of an Al₂O₃ scale on the surface of the TiAl₃‐coated sample was responsible for the enhancement of the corroison resistance. The Ti‐46.7Al‐1.9W‐0.5Si alloy was also modified by Nb ion implantation. The Nb ion implanted and as received sampels were subjected to cyclic oxidation in an open air at 800^oC. The Nb ion implantation not only increased the oxidation resistance but also substantially improved the adhesion of scale to the substrate.