Effect of changing groundwater levels caused by land-use changes on greenhouse gas fluxes from tropical peat lands

Monthly measurements of carbon dioxide (CO₂), methane (CH₄) and nitrous oxide (N₂O) fluxes in peat soils were carried out and compared with groundwater level over a year at four sites (drained forest, upland cassava,upland and lowland paddy fields) located in Jambi province, Indonesia. Fluxes from swamp forest soils were also measured once per year as the native state of this investigated area. Land-use change from drained forest to lowland paddy field significantly decreased the CO₂ (from 266 to 30 mg C m^–2 h^–1) and N₂O fluxes (from 25.4 to 3.8 g N m^–2 h^–1), but increased the CH₄ flux (from 0.1 to 4.2 mg C m^–2 h^–1) in the soils. Change from drained forest to cassava field significantly increased N₂O flux (from 25.4 to 62.2 g N m^–2 h^–1), but had no significant influence on CO₂ (from 266 to 200 mg C m^–2 h^–1) and CH₄ fluxes (from 0.1 to 0.3 mg C m^–2 h^–1) in the soils. Averaged CO₂ fluxes in the swamp forests (94 mg C m^–2 h^–1) were estimated to be one-third of that in the drained forest. Groundwater levels of drained forest and upland crop fields had been lowered by drainage ditches while swamp forest and lowland paddy field were flooded, although groundwater levels were also affected by precipitation. Groundwater levels were negatively related to CO₂ flux but positively related to CH₄ flux at all investigation sites. The peak of the N₂O flux was observed at –20 cm of groundwater level. Lowering the groundwater level by 10 cm from the soil surface resulted in a 50 increase in CO₂ emission (from 109.1 to 162.4 mg C m^–2 h^–1) and a 25% decrease in CH₄ emission (from 0.440 to 0.325 mg C m^–2 h^–1) in this study. These results suggest that lowering of groundwater level by the drainage ditches in the peat lands contributes to global warming and devastation of fields. Swamp forest was probably the best land-use management in peat lands to suppress the carbon loss and greenhouse gas emission. Lowland paddy field was a better agricultural system in the peat lands in terms of C sequestration and greenhouse gas emission. Carbon loss from lowland paddy field was one-eighth of that of the other upland crop systems, although the Global Warming Potential was almost the same level as that of the other upland crop systems because of CH₄ emission through rice plants.     

On-chip fabrication of magnetic alginate hydrogel microfibers by multilayered pneumatic microvalves

Alginate hydrogel has widespread applications in tissue engineering, cancer therapy, wound management and drug/cell/growth factor delivery due to its biocompatibility, hydrated environment and desirable viscoelastic properties. However, the lack of controllability is still an obstacle for utilizing it in the fabrication of 3D tissue constructs and accurate targeting in mass delivery. Here, we proposed a new method for achieving magnetic alginate hydrogel microfibers by dispersing magnetic nanoparticles in alginate solution and solidifying the magnetic alginate into hydrogel fiber inside microfluidic devices. The microfluidic devices have multilayered pneumatic microvalves with hemicylindrical channels to fully stop the fluids. In the experiments, the magnetic nanoparticles and the alginate solution were mixed and formed a uniform suspension. No aggregation of magnetic nanoparticles was found, which is crucial for flow control inside microfluidic devices. By regulating the flow rates of different solutions with the microvalves inside the microfluidic device, magnetic hydrogel fibers and nonmagnetic hydrogel fibers were fabricated with controlled sizes. The proposed method for fabricating magnetic hydrogel fiber holds great potential for engineering 3D tissue constructs with complex architectures and active drug release.     

Copolymerization of ethanesultam with 2-methyl-2-oxazoline

Summary This paper describes the so-called No Catalyst Copolymerization between dioxo-1,1-thiazetidine-1,2(Ethanesultam; ESm) and 2-methyl-2-oxazoline. The copolymerization took place without any added initiator to produce copolymers of MeOZO and ESm. The structure of the copolymer was determined by the IR and NMR spectra, elemental analysis, as well as by the result of an alkaline hydrolysis of the copolymer. The reaction scheme of the copolymerization via zwitterion mechanism (Eq 3–5) was proposed.     

Production of finely ground natural graphite particles with high electrical conductivity by controlling the grinding atmosphere

Natural graphite particles with high crystallinity sieved to obtain a particle size range of under 63 μm were ground with a ball mill, under various well-controlled grinding atmospheres such as N₂, O₂, He, H₂, and vacuum. The ratio, X_dif50/X_st50, i.e. between the 50 wt.% Stokes diameter and the 50 wt.% laser diffraction diameter, of the ground particles, was used as an index of the flakiness of the particles. The specific resistance of films composed of the ground graphite particles was systematically measured. The rate of reduction in the size of the particles by grinding was slow under an O₂-rich atmosphere such as 100% O₂ and dry air. On the other hand, it was relatively fast in vacuum, or under an N₂ or He atmosphere, and a gas mixture of 99% N₂ and 1% O₂. The rate of size reduction by grinding under a H₂ atmosphere was intermediate. In our experimental conditions, the flakiness of the ground particles increased with the decrease in the particles’ sizes. The electrical conductivity of the ground particles, however, tended to decrease with the decrease in their sizes. Under the condition that the Stokes diameter of the ground particles remains constant, the electrical conductivity of films made from the ground particles increases with the increase in the flakiness of the particles. It was finally determined from our systematic grinding experiments that small flaky particles, which had a size, X_st of ∼1 μm, with a high electrical conductivity can be produced by grinding in a gas mixture of 99% N₂ and 1% O₂. In this case, the flaky shape of the ground particles was visually confirmed by scanning electron microscopy.     

Plasma developable photoresist containing electronic excitation energy quenching system

A dry developable negative working resist composition comprised of poly(methyl isopropenyl ketone) (PMIPK) and 4-methyl-2,6-di(4′-azido-benzylidene) cyclohexanone-1 was examined. The main photochemical product formed in the resist pattern was found to be a secondary amine which crosslinks PMIPK. Post-annealing forms a hydrogen-bonded product which shows a powerful electronic excitation energy quenching effect. The quencher is more powerful than the aromatic compound arising from the azide by post-annealing only. The residual resist thickness of the negative pattern is about 80 percent of the initial thickness of the coating in spite of all the azide compound remaining in the resist coating. The obtained dry developed resist pattern has a high dry etch resistance. Etchings of Si and SiO₂ were performed by plasma and reactive ion etching, respectively.     

Synthesis of High Density and Transparent Forsterite Ceramics Using Nano-Sized Precursors and Their Dielectric Properties

Forsterite (Mg₂SiO₄) ceramics were prepared using Mg(OH)₂ and SiO₂ as precursors, and the effect of powder characteristics of Mg(OH)₂ on calcination and sintering was investigated. The use of highly dispersed Mg(OH)₂ powder (HD powder) resulted in a lower calcination temperature. Forsterite powder of high homogeneity and small particle size prepared from the HD powder enabled synthesis of high-density forsterite ceramics by ordinary sintering without applying external pressure. Moreover, transparent forsterite ceramics were successfully synthesized through addition of excess Mg to the precursors to compensate for Mg evaporated during the sintering process. Subsequent dielectric measurements revealed that the transparent forsterite ceramics had a very low dielectric loss (tan δ<10⁻⁴).     

Mechanism of Mechanical Strength Increase of Soda–Lime Glass by Aging

Two models have been proposed to explain the mechanical strength increase of abraded or indented soda–lime glasses upon aging, namely, crack tip blunting and the release of residual tensile stress near the crack tip. To clarify the mechanism, the time dependence of the strengthening of an abraded soda–lime glass was investigated. Effects of aging media, such as moist air, distilled water, 1 N HCI and 1 N NaOH solutions, as well as the abrasion flaw depth, were determined. The strength increase rate in water of abraded soda–lime glass was compared with those of borosilicate and high-silica glasses. The effect of stressing during aging was also investigated. It was found that the rate of strength increase was faster with decreasing abrasion flaw depth and with decreasing chemical durability. For a given flaw depth, an acidic solution produced the fastest strengthening. The strengthening rate was found to accelerate because of the "coaxing'effect of stressing during aging. From these observations, it was concluded that the strengthening rates relate to the diffusion process and chemical reactions, especially the alkali–hydrogen (or hydronium) ion-exchange reaction, near the crack tip. The role of the residual tensile stress appears to be similar to that of the applied tensile stress, helping the diffusion process near the crack tip. The observed strength increase of soda–lime glass by aging was thus attributed to the effective blunting of the crack tip geometry by the glass–water reaction.     

Photoelastic confirmation of surface stress relaxation in silica glasses: Fiber bending and rod torsion

Silica glass samples were given various heat treatments under stress at low temperatures and subsequently their residual stress distributions in terms of retardance were observed using a polarized light microscope, confirming previously reported fast surface stress relaxation while providing more detailed characterization. Retardance profiles of silica glass fibers heat-treated under a constant bending strain in the presence of atmospheric water vapor were measured and fit to a previously developed diffusion-based relaxation model. The retardance of a cross-section of a silica glass rod heat-treated at 650°C in lab air under applied torsional shear strain was also measured to confirm the presence of residual surface shear stress which was predicted by the decrease of torque with time for the rod. Together, these results confirm the low-temperature fast surface stress relaxation which occurs when water vapor is present for both bending and shear stresses.     

Microhardness measurements and the Hall-Petch relationship in an AlMg alloy with submicrometer grain size

An Al-3% Mg solid solution alloy was subjected to intense plastic deformation, using either equal-channel angular (ECA) pressing or torsion straining, to produce grain sizes in the submicrometer range. Static annealing at elevated temperatures led to grain growth and average grain sizes of up to > 100 μm. As-fabricated and statically annealed specimens were used to determine the variation in microhardness with grain size, and results confirm that the Hall-Petch relationship persists down to at least the finest grain size examined experimentally (∼90 nm). The results provide no evidence to support the claims of a negative Hall-Petch slope when the average grain size is very small, but there is evidence of a decrease in the slope of the Hall-Petch plot at the very finest grain sizes (< 150 nm); this is attributed to the increased participation of mobile extrinsic dislocations in the boundary regions when taking the hardness measurements.     

Role of Al2O3 layer in oxidation resistance of Cu-Al dilute alloys pre-annealed in H2 atmospheres

Copper was alloyed with small amounts of Al (0.2, 0.5, 1.0 and 2.0 mass%) to improve the oxidation resistance. Copper (6 N) and the Cu-Al alloys were oxidized at 773-1173 K in 0.1 MPa oxygen atmosphere after hydrogen annealing at 873 K. Continuous very thin Al₂O₃ layers were formed on the surface of all Cu-Al dilute alloys during the hydrogen annealing. Oxidation resistance of Cu-Al alloys was improved especially for Cu-2.0Al at 773-973 K, while it decreases on increasing the oxidation temperature. Cu-Al alloys followed the parabolic rate law at 1173 K, but most of other cases do not at and below 1073 K. Oxidation resistance for Cu-Al alloys was found relevant to the maintenance of the thin Al₂O₃ layer at the Cu₂O/Cu-Al alloy interface.